Lincoln ElectricメーカーIM10023の使用説明書/サービス説明書
ページ先へ移動 of 48
• Sales and Service through Subsidiaries and Distributors Worldwide • Cleveland, Ohio 44117-1199 U.S.A. TEL: 216.481.8100 FAX: 216.486.1751 WEB SITE: www.
OPERA T OR’S MANUAL FOR ENGINE pow ered equipment. 1.a. Turn the engine off before troubleshooting and maintenance work unless the maintenance work requires it to be running. ____________________________________________________ 1.b. Operate engines in open, well-ventilated areas or vent the engine exhaust fumes outdoors.
ARC R A Y S can bur n. 4.a. Use a shield with the proper filter and cover plates to protect your eyes from sparks and the rays of the arc when welding or observing open arc welding. Headshield and filter lens should conform to ANSI Z87. I standards. 4.
FOR ELECTRIC ALL Y pow ered equipment. 8.a. Turn off input power using the disconnect switch at the fuse box before working on the equipment. 8 . b . Install equipment in accordance with the U.S. National Electrical Code, all local codes and the manufacturer’s recommendations.
iv SAFETY iv PRÉC A UTIONS DE SÛRETÉ Pour votre propre protection lire et observer toutes les instructions et les précautions de sûreté specifiques qui parraissent dans ce manuel aussi bien que les précautions de sûreté générales suiv- antes: Sûreté Pour Soudage A L’Arc 1.
v v Thank Y ou for selecting a QUALITY product by Lincoln Electric. We want you to take pride in operating this Lincoln Electric Company product ••• as much pride as we have in bringing this product to you! Read this Operators Manual completely before attempting to use this equipment.
vi vi T ABLE OF CONTENTS Page –––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––– Installation .
A-1 INST ALLA TION MAXsa™ 10 CONTROLLER A-1 TECHNICAL SPECIFICA TIONS: MAXsa ™ 10 CONTROLLER INPUT VOLTAGE & CURRENT PHYSICAL SIZE• TEMPERATURE RATING Dimensions Model Voltage* - - Input Amps* Height Width Depth Weight Operating Storage K2814-1 40VDC 1.
A-2 INST ALLA TION MAXsa™ 10 CONTROLLER A-2 SAFETY PRECAUTION WELDING VOL T AGE Wire feed parts are electrically live while welding and while inching wire (with Touch Sense feature selection).
A-3 INST ALLA TION MAXsa™ 10 CONTROLLER A-3 FIGURE A.1 - MAXsa™ 10 CONNECTIONS ACCESS HOLES TC-3 TRA VEL CARRIAGE CONNECTOR FLUX HOPPER CONNECTOR POWER W A VE® AC/DC 1000 SD ARCLINK CONNECTOR PEN.
A-4 INST ALLA TION MAXsa™ 10 CONTROLLER A-4 FIGURE A.2 - HAND HELD PENDANT Cover Screws (4 places) Pendant Screws ( 2 Places) K1543-xx or K2683-xx Arclink Cable (Optional) Cover F ront View Cover removed Access Hole 1 3 2 INTERF ACING TO THE MAXsa™ 10 CON- TROLLER The MAXsa™ 10 CONTROLLER is a versatile con- troller.
A-5 INST ALLA TION MAXsa™ 10 CONTROLLER A-5 Auxiliary Input Power Connection Instructions Use the appropriate size leads, at least 14 AWG – 2 wire with ground. 1. Remove two Phillips Head screws on right side of front panel of hinged door to access terminal strip.
A-6 INST ALLA TION MAXsa™ 10 CONTROLLER A-6 SWITCH GROUP #2 SUPPLY 3-PIN FLUX REC EP TACLE A B C TERMINAL S TRIP CR3 INPUT #8 852 855 858 859 CR3 NO #2 CR3 NO #6 CR3 NC #3 CR3 INPUT #4 CR1 INPUT #8 .
A-7 INST ALLA TION MAXsa™ 10 CONTROLLER A-7 SHUTDOWN INPUTS The MAXsa™ 10 CONTROLLER has two shutdown inputs available on the terminal strip. These are inde- pendent, normally closed inputs that can be used for limit switches, PLC inputs, etc, in order to shut down the welding operation for any reason.
A-8 INST ALLA TION MAXsa™ 10 CONTROLLER A-8 K154 3-X X or K2683-XX Arcli nk Cable 67 Lead K178 5-X X 14-Pin C ab le Wo rk K231-X X Contact Nozz le K 280 3-1 Power W ave ® AC/DC 1000SD K281 4-1 MAXs.
B-1 OPERA TION B-1 MAXsa™ 10 CONTROLLER SAFETY PRECAUTIONS Read this entire section of operating instructions before operating the machine. ELECTRIC SHOCK can kill. • Do not touch electrically live parts or electrodes with your skin or wet clothing.
B-2 OPERA TION B-2 MAXsa™ 10 CONTROLLER PRODUCT DESCRIPTION GENERAL PHYSICAL DESCRIPTION • The MAXsa™ 10 CONTROLLER is a user interface and a feeder controller. The control is used to set all welding parameters and control any travel mech- anisms.
B-3 OPERA TION B-3 MAXsa™ 10 CONTROLLER FIGURE B.1 - INPUT AND OUTPUT CONNECTIONS ACCESS HO L ES T C- 3 T RA VEL CARRIAG E CO NNECT O R F L UX H O PPER CO NNECT O R PO W ER W A VE® AC/DC 1 000 SD A.
B-4 OPERA TION B-4 POWER-UP SEQUENCE When power is first applied to the machine the MODE SELECT Display reads “MAXsa™ Initializing...”. Once the PowerWave AC/DC has intialized (20 to 60 sec- onds) a “lamp test” is performed.
B-5 OPERA TION B-5 CHANGING AND SETTING WELD MODES To select a weld mode, press the WELD MODE SELECTOR button until the WELD MODE indicator comes ON (it may already be lit by default at power up). Turn the control knob to select the desired mode. After about 1 second, the parameters for the new mode will be displayed.
B-6 OPERA TION B-6 MUL TIPLE ARC CONFIGURA TION Power Wave ® AC/DC 1000 SD / MAXsa™ systems can be used in multiple arc set ups with up to six arcs. To minimize magnetic interaction between the arcs, it is imperative that they be phased correctly. Phasing is essentially a time offset between the waveforms of dif- ferent arcs.
B-7 OPERA TION B-7 MAXsa™ 10 CONTROLLER WELD SEQUENCE The weld sequence defines the weld procedure from beginning to end. All adjustments are made through the user interface.
B-8 OPERA TION B-8 MAXsa™ 10 CONTROLLER END OPTIONS The downslope, crater, and burnback parameters are used to define the end of the weld sequence. The are defined in the following: • DOWNSLOPE determines the amount of time it takes to ramp from the weld parameters to the crater parameters.
B-9 OPERA TION B-9 The Setup Menu provides access for configuring user preferences, which are generally only set at installation. The user preferences are grouped as shown in the following table. MAXsa™ 10 CONTROLLER SETUP MENU FEA TURES ACCESSING THE SETUP MENU 1.
B-10 OPERA TION B-10 Parameter Definition Exit Setup Menu P .0 This option is used to exit the setup menu. When P.0 is displayed, press the Left Button to exit the setup menu P .1 Wire Feed Speed Units This option selects which units to use for displaying wire feed speed.
B-11 OPERA TION B-11 Parameter Definition P .15 Hot-Inch T ouch Sense Option This option allows enabling or disabling touch sense when feeding wire forward. Disabled = Touch sensing is disabled when feeding the wire forward (default). Enabled = Touch sensing is active when feeding the wire forward.
B-12 OPERA TION B-12 MAXsa™ 10 CONTROLLER Parameter Definition P .101 View Event Logs Used for viewing all the system event logs. Press the Right Button to enter the option. Rotate Control Knob to select the desired event log to read. Press the Right Button again to enter the selected log.
B-13 OPERA TION B-13 MAXsa™ 10 CONTROLLER Parameter Definition P .502 Memory Change Lockout Determines if the memories can be overwritten with new contents. No = Memories can be saved and limits can be configured (default). Yes = Memories cannot be changed - saving is prohibited and limits cannot be re-configured.
TOUCH SENSE The Touch Sense option, when enabled, allows the operator to feed the wi re forward until i t touches the workpiece. When contact to the work is made, the wire will stop and the flux hopper (if used) will activate to put flux around the wire and fill t he flux feed sys- tem.
B-15 OPERA TION B-15 Press the START BUTTON to begin welding. The ARC ESTABLISHED INDICATOR will ‘ flash’ as the wire feeds towards the work piece to show that OCV is present and switch to ON when the arc is lit.
B-16 OPERA TION B-16 The MAXsa™ 10 has eight available memory loca- tions for storing procedural information. Each location will store the following information: • Weld Mode • Amperage(or WFS) .
B-17 OPERA TION B-17 SA VING A PROCEDURE TO A MEMORY LOCA TION Once the parameters have been set: • Press and Hold the M e m o r y B u t t o n o f t h e desired location for 2 seconds.
B-18 OPERA TION B-18 The Limits feature allows the operator to set minimum and maximum values for various parameters depending on the Weld Mode selected.
C-1 ACCESSORIES C-1 OPTIONS AND ACCESSORIES are available at www .lincolnelectric.com Follow these steps: 1. Go to www.lincolnelectric.com 2. In the Search field type E9.181 and click on the Search icon (or hit ‘Enter’ on the keyboard). 3. On the Results page, scroll down to the Equipment list and click on E9.
D-1 MAINTENANCE D-1 ROUTINE MAINTENANCE • Check weld cables, control cables and gas hoses for cuts. PERIODIC MAINTENANCE • N/A CALIBRA TION SPECIFICA TION All calibration is factory set on the MAXsa™ 10 CON- TROLLER.
E-1 TROUBLESHOOTING E-1 MAXs™ 10 CONTROLLER If for any reason you do not understand the test procedures or are unable to perform the tests/repairs safely, contact your Local Lincoln Authorized Field Service Facility for technical troubleshooting assistance before you proceed.
E-2 TROUBLESHOOTING E-2 MAXsa™ 10 CONTROLLER Observe all Safety Guidelines detailed throughout this manual If for any reason you do not understand the test procedures or are unable to perform the tests/repairs safely, contact your Local Lincoln Authorized Field Service Facility for technical troubleshooting assistance before you proceed.
E-3 TROUBLESHOOTING E-3 MAXsa™ 10 CONTROLLER If for any reason you do not understand the test procedures or are unable to perform the tests/repairs safely, contact your Local Lincoln Authorized Field Service Facility for technical troubleshooting assistance before you proceed.
E-4 TROUBLESHOOTING E-4 Observe all Safety Guidelines detailed throughout this manual PROBLEMS (SYMPTOMS) POSSIBLE CAUSE RECOMMENDED COURSE OF ACTION If all recommended possible areas of misadjustment have been checked and the problem persists, Contact your local Lincoln Authorized Field Service Facility.
E-5 TROUBLESHOOTING E-5 MAXsa™ 10 CONTROLLER If for any reason you do not understand the test procedures or are unable to perform the tests/repairs safely, contact your Local Lincoln Authorized Field Service Facility for technical troubleshooting assistance before you proceed.
E-6 TROUBLESHOOTING E-6 MAXsa™ 10 CONTROLLER Observe all Safety Guidelines detailed throughout this manual If for any reason you do not understand the test procedures or are unable to perform the tests/repairs safely, contact your Local Lincoln Authorized Field Service Facility for technical troubleshooting assistance before you proceed.
E-7 TROUBLESHOOTING E-7 MAXsa™ 10 CONTROLLER Observe all Safety Guidelines detailed throughout this manual If for any reason you do not understand the test procedures or are unable to perform the tests/repairs safely, contact your Local Lincoln Authorized Field Service Facility for technical troubleshooting assistance before you proceed.
E-8 TROUBLESHOOTING E-8 MAXsa™ 10 CONTROLLER Observe all Safety Guidelines detailed throughout this manual If for any reason you do not understand the test procedures or are unable to perform the tests/repairs safely, contact your Local Lincoln Authorized Field Service Facility for technical troubleshooting assistance before you proceed.
F-1 DIAGRAMS F-1 MAXsa™ 10 CONTROLLER NOTE: This diagram is for reference only. It may not be accurate for all machines covered by this manual. The specific diagram for a particular code is pasted inside the machine on one of the enclosure panels. If the diagram is illegible, write to the Service Department for a replacement.
F-2 DIMENSION PRINT F-2 MAXsa™ 10 CONTROLLER 5.89 .20 11.30 13.25 12.25 11.68 O .66 O .28 14.40 .87 7.75 8.90 7.07 1.64 1.50 SCALE = 1 : 4 PENDANT L13444.
W ARNING A VISO DE PREC A UCION A TTENTION W ARNUNG A TENÇÃO Spanish French German Portuguese Japanese Chinese Korean Arabic READ AND UNDERST AND THE MANUF A CTURER’S INSTRUCTION FOR THIS EQUIPMENT AND THE CONSUMABLES TO BE USED AND FOLL O W Y OUR EMPL O YER’S SAFETY PR A CTICES.
W ARNING A VISO DE PREC A UCION A TTENTION W ARNUNG A TENÇÃO Spanish French German Portuguese Japanese Chinese Korean Arabic LEIA E COMPREEND A A S INSTR UÇÕES DO F ABRIC ANTE P ARA ES TE EQUIP AMENT O E AS P ARTES DE USO , E SIG A A S PRÁTIC A S DE SEGUR ANÇA DO EMPREG ADOR.
• Sales and Service through Subsidiaries and Distributors Worldwide • Cleveland, Ohio 44117-1199 U.S.A. TEL: 216.481.8100 FAX: 216.486.1751 WEB SITE: www.
デバイスLincoln Electric IM10023の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Lincoln Electric IM10023をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはLincoln Electric IM10023の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Lincoln Electric IM10023の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Lincoln Electric IM10023で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Lincoln Electric IM10023を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はLincoln Electric IM10023の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Lincoln Electric IM10023に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちLincoln Electric IM10023デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。