Lincoln ElectricメーカーIM604-Bの使用説明書/サービス説明書
ページ先へ移動 of 38
OPERA TOR’S MANUAL Safety Depends on You Lincoln arc welding and cutting equipment is designed and built with safety in mind. However, your overall safety can be increased by proper installation .
FOR ENGINE powered equipment. 1.a. Turn the engine off before troubleshooting and maintenance work unless the maintenance work requires it to be running. ____________________________________________________ 1.b. Operate engines in open, well-ventilated areas or vent the engine exhaust fumes outdoors.
ii SAFETY ii ARC RA YS can burn. 4.a. Use a shield with the proper filter and cover plates to protect your eyes from sparks and the rays of the arc when welding or observing open arc welding. Headshield and filter lens should conform to ANSI Z87. I standards.
FOR ELECTRICALL Y powered equipment. 8.a. Turn off input power using the disconnect switch at the fuse box before working on the equipment. 8.b. Install equipment in accordance with the U.S. National Electrical Code, all local codes and the manufacturer’s recommendations.
iv SAFETY iv PRÉCAUTIONS DE SÛRETÉ Pour votre propre protection lire et observer toutes les instruc- tions et les précautions de sûreté specifiques qui parraissent dans ce manuel aussi bien que les précautions de sûreté générales suivantes: Sûreté Pour Soudage A L’Arc 1.
RANGER 8 LPG Thank You for selecting a QUALITY product by Lincoln Electric. We want you to take pride in operating this Lincoln Electric Company product ••• as much pride as we have in bringing this product to you! Read this Operators Manual completely before attempting to use this equipment.
vi vi T ABLE OF CONTENTS Page SAFETY PRECAUTIONS .......................................................................................i - iv INTRODUCTORY INFORMATION ............................................................................v GENERAL DESCRIPTION .
1 1 RANGER 8 LPG GENERAL DESCRIPTION The Ranger ™ 8 LPG is a twin-cylinder LPG fuel engine driven multiprocess arc welder and AC power genera- tor. It is built in a heavy gauge steel case for durability on the job site.
2 2 RANGER 8 LPG Machine Product Name Ordering Information K1616-1 Description Multi-Purpose Arc Welder with 8,000 watts of Auxiliary Power AC Constant Current 225A / 25V / 100% DC Constant Current 210A / 25V / 100% DC Constant Voltage 200A / 20V / 100% Max.
3 3 RANGER 8 LPG AC STICK / TIG (CC) OUTPUT A 225 OUTPUT RANGE B 50 OUTPUT RANGE A B OUTPUT AMPS OUTPUT VOLTS AC 0 50 100 150 200 250 0 10 20 30 40 50 60 70 80 DC STICK / TIG (CC) OUTPUT OUTPUT AMPS O.
4 4 RANGER 8 LPG OPTIONAL EQUIPMENT (Field Installed) Four Wheel Undercarriage (K933-1) - Allows move- ment of the Ranger 8 by hand without lifting. Easily assembles to the Ranger 8. Includes two rugged, hard molded wheels and two durable, two ply nylon 4.
5 5 RANGER 8 LPG RECOMMENDED EQUIPMENT STICK Accessory Kit (K710) which includes: • Electrode Holder & Cable • Work Clamp & Cable • Headshield Remote Control Receptacle Kit (K892-1), and Remote Control Kit (K857) are optional for remote current control.
6 6 RANGER 8 LPG INST ALLA TION INSTRUCTIONS Safety Precautions Machine Grounding Because this portable engine driven welder or gener- ator creates it’s own power, it is not necessary to con- nect it’s frame to an earth ground, unless the machine is connected to premises wiring (your home, shop, etc.
7 7 RANGER 8 LPG • The stem of the cylinder valve and where the valve is attached to the top of the cylinder. • All other fittings on top of the fuel cylinder. If growing bubbles appear, there is a leak. Re-tighten connection or replace defective component.
8 8 RANGER 8 LPG Battery Connections This welder is shipped with the negative battery cable disconnected. Make sure that the Engine Switch is in the “OFF” position and attach the disconnected cable securely to the negative battery terminal before attempting to operate the machine.
9 9 RANGER 8 LPG Angle of Operation Internal combustion engines are designed to run in a level condition which is where the optimum perfor- mance is achieved. The maximum angle of operation for the engine is 25 degrees from horizontal in any direction.
10 10 RANGER 8 LPG Connection of the LN-7 to the Ranger 8 a. Shut the welder off. b. Connect the LN-7 and the K240 contactor kit per instructions on the connection diagram S17742 (can be found in the back of this manual). c. Place the “RANGE” switch to the “WIRE FEED” position and the “POLARITY” switch to the desired polarity.
a. Welding When the electrode touches the work, the welding arc is initiated and the engine accelerates to full speed. After welding ceases (and no auxiliary power is being drawn), the engine will return to low idle after approximately 10 to 14 seconds.
12 12 RANGER 8 LPG After running at high engine speed for 10-14 seconds, the engine will go to low idle. Allow the engine to warm up by letting it run at low idle for a few minutes. Stopping the Engine Remove all welding and auxiliary power loads and allow engine to run at low idle speed for a few minutes to cool the engine.
13 13 RANGER 8 LPG Wire Feed Welding Processes (Constant Voltage) The only Innershield ® electrode recommended for use with the Ranger 8 is NR ® -211-MP. The electrode sizes and welding ranges that can be used with the Ranger 8 are shown in the following table: Diameter Wire Speed Approximate (in.
14 14 RANGER 8 LPG The current rating of any plug used with the system must be at least equal to the current load through the associated receptacles (see tables below). Do not attempt to connect power receptacles in parallel. * Maximum current draw from each 115V GFCI Duplex receptacle is 20 amps.
15 15 RANGER 8 LPG 1. Install a double pole, double throw switch between the power company meter and the premises disconnect. Switch rating must be the same or greater than the customer’s premises disconnect and service overcurrent protection.
16 16 RANGER 8 LPG CAUTION Certain Electrical devices cannot be powered by the RANGER 8 LPG. See Table A.2. TABLE A.2 ELECTRICAL DEVICE USE WITH THE RANGER 8 LPG. Type Common Electrical Devices Possible Concerns Resistive Heaters, toasters, incandescent NONE light bulbs, electric range, hot pan, skillet, coffee maker.
17 17 RANGER 8 LPG MAINTENANCE Safety Precautions Read the Safety Precautions in the front of this manu- al and the engine instruction manual before working on this machine. Keep all equipment safety guards, covers, and devices in position and in good repair.
18 18 RANGER 8 LPG 1. When replacing, jumping, or otherwise connecting the battery to the battery cables, the proper polarity must be observed. Failure to observe the proper polarity could result in damage to the charging circuit. The positive (+) battery cable has a red terminal cover.
19 TROUBLESHOOTING 19 RANGER 8 LPG TROUBLE A. No welder or output power. B. Engine will not idle down to low speed. C. Engine will not go to high idle when attempting to weld. CAUSE 1. Open in miscellaneous leads. 2. Open lead in flashing or field circuit.
20 TROUBLESHOOTING 20 RANGER 8 LPG TROUBLE D. Engine will not go to high idle when using auxiliary power. E. Engine will not crank or is hard to crank. F. Engine shuts down. G. Engine does not develop full power. H. Engine is hard to start. CAUSE 1. No voltage signal from the current sensor.
21 WIRING DIAGRAM 21 RANGER 8 LPG STARTER CR1 STARTER SOLENOID 12 VOLT IDLER SOLENOID 213 BATTERY AC AC B+ SWITCH REGULATOR FLYWHEEL ALTERNATOR B- HOUR METER 5E 5D S4 224B 224 213 "S4" SHOWN IN "AUTO" POSITION ENGINE COMPONENTS 224A 1 2 3 CONNECTOR PIN NUMBERS: 7 6 12 1 2 3 4 J1 LEAD COLOR CODE: B = BLACK R = RED W = WHITE N.
22 DIAGRAMS 22 RANGER 8 LPG STARTER CR1 STARTER SOLENOID 12 VOLT IDLER SOLENOID 213 BATTERY AC AC B+ SWI TCH REGULATOR FLYWHEEL ALTERNATOR B- HOUR METER 5E 5D S4 224B 224 213 "S4" SHOWN IN "AUTO" POSITION ENGINE COMPONENT S 224A 1 2 3 CONNECTOR PIN NUMBERS: 7 6 12 1 2 3 4 J1 N.
23 CONNECTION DIAGRAMS 23 RANGER 8 LPG CONNECTION OF RANGER 8 TO LN-7 & K240 CONT ACTOR KIT WARNING: Turn the power off when making connections. N.A. Use power source polarity switch to set for desired electrode polarity. Position the output selector switch on the power source to the CV position.
9.29 21.21 21.95 43.80 17.00 26.59 30.28 19.11 9.31 M17215-4 CRM28731 9.09 9.09 UNDERCARRIAGE MOUNTING HOLES 42.25 42.00 CENTER OF GRAVITY WITH OIL IN ENGINE AND FULL FUEL TANK.
NOTES RANGER 8 LPG.
NOTES RANGER 8 LPG.
NOTES RANGER 8 LPG.
There is a 10% discount on all orders of $50.00 or more for shipment at one time to one location. Orders of $50 or less before discount or orders outside of North America must be prepaid with charge, check or money order in U .S. Funds Only. Prices include shipment by 4 th Class Book Rate for U.
W ARNING A VISO DE PRECAUCION A TTENTION W ARNUNG A TEN ÇÃ O Spanish French German Portuguese Japanese Chinese Korean Arabic READ AND UNDERST AND THE MANUF ACTURER’S INSTRUCTION FOR THIS EQUIPMENT AND THE CONSUMABLES TO BE USED AND FOLLOW YOUR EMPLOYER’S SAFETY PRACTICES.
W ARNING A VISO DE PRECAUCION A TTENTION W ARNUNG A TEN ÇÃ O Spanish French German Portuguese Japanese Chinese Korean Arabic LEIA E COMPREENDA AS INSTRUÇÕES DO F ABRICANTE PARA ESTE EQUIP AMENTO E AS P ARTES DE USO, E SIGA AS PRÁTICAS DE SEGURANÇA DO EMPREGADOR.
• Sales and Service through Subsidiaries and Distributors Worldwide • Cleveland, Ohio 44117-1199 U.S.A. TEL: 216.481.8100 FAX: 216.486.1751 WEB SITE: www.
デバイスLincoln Electric IM604-Bの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Lincoln Electric IM604-Bをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはLincoln Electric IM604-Bの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Lincoln Electric IM604-Bの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Lincoln Electric IM604-Bで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Lincoln Electric IM604-Bを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はLincoln Electric IM604-Bの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Lincoln Electric IM604-Bに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちLincoln Electric IM604-Bデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
