Lincoln ElectricメーカーIM692の使用説明書/サービス説明書
ページ先へ移動 of 26
MUL TI-SOURCE OPERA TOR’S MANUAL For use with machines Code 10668 October, 2000 IM692 Safety Depends on You Lincoln arc welding equipment is designed and built with safety in mind. However, your overall safety can be increased by proper instal- lation .
FOR ENGINE powered equipment. 1.a. Turn the engine off before troubleshooting and maintenance work unless the maintenance work requires it to be running. ____________________________________________________ 1.b. Operate engines in open, well-ventilated areas or vent the engine exhaust fumes outdoors.
ii SAFETY ii ARC RA YS can burn. 4.a. Use a shield with the proper filter and cover plates to protect your eyes from sparks and the rays of the arc when welding or observing open arc welding. Headshield and filter lens should conform to ANSI Z87. I standards.
FOR ELECTRICALL Y powered equipment. 8.a. Turn off input power using the disconnect switch at the fuse box before working on the equipment. 8.b. Install equipment in accordance with the U.S. National Electrical Code, all local codes and the manufacturer’s recommendations.
iv SAFETY iv PRÉCA UTIONS DE SÛRETÉ Pour votre propre protection lire et observer toutes les instructions et les précautions de sûreté specifiques qui parraissent dans ce manuel aussi bien que les précautions de sûreté générales suiv- antes: Sûreté Pour Soudage A L’Arc 1.
Thank You for selecting a QUALITY product by Lincoln Electric. We want you to take pride in operating this Lincoln Electric Company product ••• as much pride as we have in bringing this product to you! Read this Operators Manual completely before attempting to use this equipment.
vi T ABLE OF CONTENTS Page Installation ................................................................................................................... ....Section A Technical Specifications ........................................................
A-1 INST ALLA TION MULTI-SOURCE A-1 TECHNICAL SPECIFICA TIONS - Multi-Source K1752-1 PHYSICAL DIMENSIONS TEMPERA TURE RANGES HEIGHT 30.8 in 781 mm WIDTH 22.
A-2 INST ALLA TION MULTI-SOURCE A-2 LOCA TION Place the power supply where clean cooling air can freely circulate in through the front louvers and out through the rear louvers. Dirt, dust or any foreign material that can be drawn into the welder should be kept at a minimum.
A-3 INST ALLA TION MULTI-SOURCE A-3 OUTPUT CABLES, CONNECTIONS AND LIMIT A TIONS The Multi-Source has two parallel connected output studs for positive and negative connections. Each one is rated to carry the full output current. For its maxi- mum rated current at 100% duty cycle a minimum size of 4/0 AWG is recommended.
Other indicator lights include the amber Thermal light that signals when the long term output current limit has been exceeded. This limit is determined by a ther- mostat sensing the temperature of the negative output lead from the secondary coils. The white Power light indicates when the Control board is energized.
C-1 A CCESSORIES C-1 F A CT OR Y INST ALLED OPTIONS / A CCESSORIES There are no factory installed options. MULTI-SOURCE FIELD INST ALLED OPTIONS / A CCESSORIES K1735-1 Multi-Weld 350, Multi-process controller. K857, K857-1 Remote Control, Control Multi-Weld remotely (25 or 100 ft.
D-1 MAINTENANCE D-1 MULTI-SOURCE SAFETY PRECA UTIONS Have qualified personnel do the maintenance work. Always use the greatest care when working near moving parts. If a problem cannot be corrected by following the instructions, take the machine to the nearest Lincoln Field Service Shop.
MULTI-SOURCE E-1 TR OUBLESHOO TING E-1 If for any reason you do not understand the test procedures or are unable to perform the tests/repairs safely, contact your Local Lincoln Authorized Field Service Facility for technical troubleshooting assistance before you proceed.
E-2 TR OUBLESHOO TING E-2 MULTI-SOURCE Observe all Safety Guidelines detailed throughout this manual If for any reason you do not understand the test procedures or are unable to perform the tests/repairs safely, contact your Local Lincoln Authorized Field Service Facility for technical troubleshooting assistance before you proceed.
E-3 TR OUBLESHOO TING E-3 MULTI-SOURCE Observe all Safety Guidelines detailed throughout this manual If for any reason you do not understand the test procedures or are unable to perform the tests/repairs safely, contact your Local Lincoln Authorized Field Service Facility for technical troubleshooting assistance before you proceed.
5. LEDs 1 through 6 indicate gate signals are being sent to the main SCRs 1 through 6 respectively. If LED2 on the Control board is bright, along with LEDs 7, 8, and 9 on Firing board, and LEDs 1 through 6 are unequal in brightness, check to make sure lead 231 between Control board and Firing board is not broken.
E-5 TR OUBLESHOO TING E-5 MULTI-SOURCE Observe all Safety Guidelines detailed throughout this manual If for any reason you do not understand the test procedures or are unable to perform the tests/repairs safely, contact your Local Lincoln Authorized Field Service Facility for technical troubleshooting assistance before you proceed.
F-1 DIA GRAMS F-1 MULTI-SOURCE CONTROL PC BOARD FIR ING PC BOARD 56 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 7 8 9 10 1 2 273 274 252 251 3 4 5 6 7 240 8 241 222D R3 R4 R5 R6 R7 R8 283 284 285 286 287 2.
F-2 DIA GRAMS F-2 MULTI-SOURCE 40.96 20.69 27.59 3.16 22.23 20.00 20.00 38.11 36.11 30.02 29.31 2.07 1.37 18.62 1.18 3.25 27.95 11.12 M19588 MUL TI-SOURCE DIMENSION PRINT A.
NO TES.
NO TES.
Now A vailable...12th Edition The Procedure Handbook of Ar c W elding With over 500,000 copies of previous editions published since 1933, the Procedure Handbook is considered by many to be the “Bible” of the arc welding industry. This printing will go fast so don’t delay.
W ARNING A VISO DE PRECA UCION A TTENTION W ARNUNG A TEN ÇÃ O Spanish French German Portuguese Japanese Chinese Korean Arabic READ AND UNDERST AND THE MANUF ACTURER’S INSTRUCTION FOR THIS EQUIPMENT AND THE CONSUMABLES TO BE USED AND FOLLOW YOUR EMPLOYER’S SAFETY PRACTICES.
W ARNING A VISO DE PRECA UCION A TTENTION W ARNUNG A TEN ÇÃ O Spanish French German Portuguese Japanese Chinese Korean Arabic LEIA E COMPREENDA AS INSTRUÇÕES DO F ABRICANTE P ARA ESTE EQUIP AMENTO E AS PAR TES DE USO, E SIGA AS PRÁTICAS DE SEGURANÇA DO EMPREGADOR.
• Sales and Service through Subsidiaries and Distributors Worldwide • Cleveland, Ohio 44117-1199 U.S.A. TEL: 216.481.8100 FAX: 216.486.1751 WEB SITE: www.
デバイスLincoln Electric IM692の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Lincoln Electric IM692をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはLincoln Electric IM692の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Lincoln Electric IM692の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Lincoln Electric IM692で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Lincoln Electric IM692を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はLincoln Electric IM692の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Lincoln Electric IM692に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちLincoln Electric IM692デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。