Lincoln ElectricメーカーIM904の使用説明書/サービス説明書
ページ先へ移動 of 38
INVERTEC ® S T T ® II (CE) OPERA T OR’S MANUAL IM904 July, 2006 Safety Depends on You Lincoln arc welding and cutting equipment is designed and built with safety in mind. However, your overall safety can be increased by proper installation ... and thoughtful operation on your part.
FOR ENGINE powered equipment. 1.a. Turn the engine off before troubleshooting and maintenance work unless the maintenance work requires it to be running. ____________________________________________________ 1.b. Operate engines in open, well-ventilated areas or vent the engine exhaust fumes outdoors.
ii SAFETY ii ARC RA YS can burn. 4.a. Use a shield with the proper filter and cover plates to protect your eyes from sparks and the rays of the arc when welding or observing open arc welding. Headshield and filter lens should conform to ANSI Z87. I standards.
FOR ELECTRICALL Y powered equipment. 8.a. Turn off input power using the disconnect switch at the fuse box before working on the equipment. 8.b. Install equipment in accordance with the U.S. National Electrical Code, all local codes and the manufacturer’s recommendations.
iv SAFETY iv PRÉCAUTIONS DE SÛRETÉ Pour votre propre protection lire et observer toutes les instructions et les précautions de sûreté specifiques qui parraissent dans ce manuel aussi bien que les précautions de sûreté générales suiv- antes: Sûreté Pour Soudage A L’Arc 1.
v v Thank You for selecting a QUALITY product by Lincoln Electric. We want you to take pride in operating this Lincoln Electric Company product ••• as much pride as we have in bringing this product to you! Read this Operators Manual completely before attempting to use this equipment.
vi vi T ABLE OF CONTENTS Page Safety .....................................................................................................................i-iv Installation ...............................................................................
INVERTEC STT II (CE) A-1 INST ALLA TION A-1 STANDARD VOLTAGE INPUT CURRENT AT RATED OUTPUT 200/220/380/415/440/3/50/60 HZ 33/30/18/17/16 TECHNICAL SPECIFICA TIONS –INVERTEC STT II (CE) (For Code 1 1.
A-2 INST ALLA TION A-2 INVERTEC STT II (CE) STANDARD VOLTAGE INPUT CURRENT AT RATED OUTPUT 200/208/380/400/415/3/50/60 HZ 36/34/20/19/18 TECHNICAL SPECIFICA TIONS –INVERTEC STT II (CE) (For Code 1 1.
A-3 INST ALLA TION A-3 INVERTEC STT II (CE) ELECTRIC SHOCK can kill. • Only qualified personnel should perform this installation. • Turn the input power OFF at the disconnect switch or fuse box before installing this equipment.
A-4 INST ALLA TION A-4 INVERTEC STT II (CE) INPUT CABLE INST ALLA TION AND CON- NECTION A cable strain relief is provided at the supply line entry and is designed to accommodate cable diameters of .310 - 1.070 in. (7.9 - 27.2 mm). On European models the strain relief is designed to accommodate cable diameters of .
A-5 INST ALLA TION A-5 INVERTEC STT II (CE) FIGURE A.2 RECONNECT P ANEL I NPUT VOL T AGE RECONNECT PROCEDURE As shipped from the factory, multiple voltage machines are internally configured for the highest input voltage (440-460 VAC), for Code 11366 and (380-415 VAC), for Code 11367.
B-1 OPERA TION B-1 INVERTEC STT II (CE) ELECTRIC SHOCK can kill. • Do not touch electrically live parts or electrode with skin or wet clothing. • Insulate yourself from work and ground. • Always wear dry insulating gloves. FUMES AND GASES can be dangerous.
B-2 OPERA TION B-2 INVERTEC STT II (CE) GENERAL DESCRIPTION The INVERTEC STT II (CE) is a 225-ampere inverter based arc welding power source specifically designed for the STT welding process. It is neither a constant current (CC) nor a constant voltage (CV) machine.
B-3 OPERA TION B-3 INVERTEC STT II (CE) 1. POWER SWITCH: Turns output power ON and OFF. This switch also controls auxiliary power available through the 14-pin Wire Feeder Receptacle. 2A. BACKGROUND CURRENT OUTPUT CON- TROL: The output current is switched to the Background level at the conclusion of the preceding Peak Current pulse.
B-4 OPERA TION B-4 INVERTEC STT II (CE) 6. WIRE SIZE SELECT SWITCH: This toggle switch selects between electrode diameters of .035 ” (1 mm) and smaller or .045 ” (1.2 mm) and larger. The .035 ” (1 mm) position provides improved perfor- mance of smaller diameter wires at higher wire feed speeds.
B-5 OPERA TION B-5 INVERTEC STT II (CE) WELDING P ARAMETERS AND GUIDE- LINES The INVERTEC STT II (CE) is neither a constant cur- rent (CC) nor a constant voltage (CV) power source. In general, wire diameter will be increased one size compared to conventional (CV) power sources.
B-6 OPERA TION B-6 INVERTEC STT II (CE) WELDING PROCEDURES FOR STT II - (Steel) Horizontal Fillet (See Table B.1 and B.2) Table B.1 100% CO 2 Gas Shield (Set for Steel Mode) Table B.2 75% CO 2 - 25% Ar Gas Shield (Set for Steel Mode) (Stainless Steel) Horizontal Fillet (See Table B.
C-1 ACCESSORIES C-1 INVERTEC STT II (CE) STT control board to accept PEAK and BACK- GROUND inputs on this connector rather than from the front panel controls. If this short is removed, the front panel controls will be active. By adding a switch between pins “ J ” and “ B ” a “ LOCAL/REMOTE ” control switch can be created.
C-2 ACCESSORIES C-2 INVERTEC STT II (CE) LN-742 or STT -10 WIRE FEEDER CONNECTION INSTRUCTIONS The LN-742 or STT-10 is the recommended wire feed- er for use with the INVERTEC STT II (CE). Refer to the LN-742 or STT-10 Operator Manual for Wire Feed Operation.
C-3 ACCESSORIES C-3 INVERTEC STT II (CE) CONNECTION DIAGRAM - INVERTEC STT II 4-9-99 M17657-3 CABLES AND LEADS SHOULD ELECTRODE LEAD BE TAPED TOGETHER.
D-1 MAINTENANCE D-1 INVERTEC STT II (CE) W ARNING Failure to follow this capacitor discharge procedure can result in electric shock. INPUT FIL TER CAP ACITOR DISCHARGE PROCEDURE 1 . Turn off input power or disconnect input power lines. 2 . Remove hex head screws from side and top of machine and remove wrap-around machine cover.
D-2 MAINTENANCE D-2 INVERTEC STT II (CE) PREVENTIVE MAINTENANCE 1. Perform the following preventive maintenance pro- cedures at least once every six months. It is good practice to keep a preventive maintenance record; a record tag attached to the machine works best.
E-1 TROUBLESHOOTING E-1 INVERTEC STT II (CE) If for any reason you do not understand the test procedures or are unable to perform the tests/repairs safely, contact your Local Lincoln Authorized Field Service Facility for technical troubleshooting assistance before you proceed.
E-2 TROUBLESHOOTING E-2 INVERTEC STT II (CE) If for any reason you do not understand the test procedures or are unable to perform the tests/repairs safely, contact your Local Lincoln Authorized Field Service Facility for technical troubleshooting assistance before you proceed.
E-3 TROUBLESHOOTING E-3 INVERTEC STT II (CE) If for any reason you do not understand the test procedures or are unable to perform the tests/repairs safely, contact your Local Lincoln Authorized Field Service Facility for technical troubleshooting assistance before you proceed.
E-4 TROUBLESHOOTING E-4 INVERTEC STT II (CE) If for any reason you do not understand the test procedures or are unable to perform the tests/repairs safely, contact your Local Lincoln Authorized Field Service Facility for technical troubleshooting assistance before you proceed.
E-5 TROUBLESHOOTING E-5 INVERTEC STT II (CE) If for any reason you do not understand the test procedures or are unable to perform the tests/repairs safely, contact your Local Lincoln Authorized Field Service Facility for technical troubleshooting assistance before you proceed.
E-6 TROUBLESHOOTING E-6 INVERTEC STT II (CE) If for any reason you do not understand the test procedures or are unable to perform the tests/repairs safely, contact your Local Lincoln Authorized Field Service Facility for technical troubleshooting assistance before you proceed.
F-1 DIAGRAMS F-1 INVERTEC STT II (CE) NOTE: This diagram is for reference only. It may not be accurate for all machines covered by this manual. The specific diagram for a particular code is pasted inside the machine on one of the enclosure panels. If the diagram is illegible, write to the Service Department for a replacement.
F-2 DIAGRAMS F-2 INVERTEC STT II (CE) NOTE: This diagram is for reference only. It may not be accurate for all machines covered by this manual. The specific diagram for a particular code is pasted inside the machine on one of the enclosure panels. If the diagram is illegible, write to the Service Department for a replacement.
F-3 DIAGRAMS F-3 INVERTEC STT II (CE) 13.19 20.75 23.25 13.21 24.50 1-9-98B M18706 DIMENSION PRINT - STT II (CE).
NOTES INVERTEC STT II (CE).
NOTES INVERTEC STT II (CE).
NOTES INVERTEC STT II (CE).
W ARNING A VISO DE PRECAUCION A TTENTION W ARNUNG A TEN ÇÃ O Spanish French German Portuguese Japanese Chinese Korean Arabic READ AND UNDERST AND THE MANUF ACTURER’S INSTRUCTION FOR THIS EQUIPMENT AND THE CONSUMABLES TO BE USED AND FOLLOW YOUR EMPLOYER’S SAFETY PRACTICES.
W ARNING A VISO DE PRECAUCION A TTENTION W ARNUNG A TEN ÇÃ O Spanish French German Portuguese Japanese Chinese Korean Arabic LEIA E COMPREENDA AS INSTRUÇÕES DO F ABRICANTE P ARA ESTE EQUIPAMENTO E AS P ARTES DE USO, E SIGA AS PRÁTICAS DE SEGURANÇA DO EMPREGADOR.
• Sales and Service through Subsidiaries and Distributors Worldwide • Cleveland, Ohio 44117-1199 U.S.A. TEL: 216.481.8100 FAX: 216.486.1751 WEB SITE: www.
デバイスLincoln Electric IM904の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Lincoln Electric IM904をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはLincoln Electric IM904の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Lincoln Electric IM904の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Lincoln Electric IM904で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Lincoln Electric IM904を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はLincoln Electric IM904の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Lincoln Electric IM904に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちLincoln Electric IM904デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。