Lincoln ElectricメーカーIM956-Aの使用説明書/サービス説明書
ページ先へ移動 of 72
• Sales and Service through Subsidiaries and Distributors Worldwide • Cleveland, Ohio 44117-1199 U.S.A. TEL: 216.481.8100 FAX: 216.486.1751 WEB SITE: www.
FOR ENGINE powered equipment. 1.a. Turn the engine off before troubleshooting and maintenance work unless the maintenance work requires it to be running. ____________________________________________________ 1.b. Operate engines in open, well-ventilated areas or vent the engine exhaust fumes outdoors.
ARC RA YS can burn. 4.a. Use a shield with the proper filter and cover plates to protect your eyes from sparks and the rays of the arc when welding or observing open arc welding. Headshield and filter lens should conform to ANSI Z87. I standards. 4. b.
FOR ELECTRICALL Y powered equipment. 8.a. Turn off input power using the disconnect switch at the fuse box before working on the equipment. 8 .b . Install equipment in accordance with the U.S. National Electrical Code, all local codes and the manufacturer’s recommendations.
PRÉCAUTIONS DE SÛRETÉ Pour votre propre protection lire et observer toutes les instructions et les précautions de sûreté specifiques qui parraissent dans ce manuel aussi bien que les précautions de sûreté générales suiv- antes: Sûreté Pour Soudage A L’Arc 1.
THIS SAMPLE DOCUMENT IS USED FOR “CE” MACHINES ONL Y! v v SAFETY Electromagnetic Compatibility (EMC) Conformance Products displaying the CE mark are in conformity with European Community Council Directive of 3 May 1989 on the approximation of the laws of the Member States relating to electromagnetic compatibility (89/336/EEC).
THIS SAMPLE DOCUMENT IS USED FOR “CE” MACHINES ONL Y! vi vi SAFETY Electromagnetic Compatibility (EMC) The size of the surrounding area to be considered will depend on the structure of the building and other activities that are taking place. The surrounding area may extend beyond the boundaries of the premises.
vii vii T T h h a a n n k k Y Y o o u u for selecting a QUALITY product by Lincoln Electric. We want you to take pride in operating this Lincoln Electric Company product ••• as much pride as we have in bringing this product to you! Read this Operators Manual completely before attempting to use this equipment.
viii viii T ABLE OF CONTENTS Page Installation .......................................................................................................................Section A Technical Specifications ..................................................
Page Maintenance ....................................................................................................Section D Safety Precautions .........................................................................................................
A-1 INST ALLA TION POWER WAVE® C300 A-1 TECHNICAL SPECIFICA TIONS - POWER W A VE® C300 RECOMMENDED INPUT WIRE AND FUSE SIZES 1 INPUT VOLTAGE / PHASE/ FREQUENCY 208/1/50/60 208/3/50/60 230/1/50/60 23.
A-2 INST ALLA TION POWER WAVE® C300 A-2 PHYSICAL DIMENSIONS TEMPERA TURE RANGES HEIGHT 20.40 in ( 518 mm) MODEL K2675-1 WIDTH 14.00in ( 356 mm) DEPTH 24.
A-3 INST ALLA TION POWER WAVE® C300 A-3 SAFETY PRECAUTIONS Read this entire installation section before you start installa- tion. ELECTRIC SHOCK can kill. • Only qualified personnel should perform this installation. • Turn the input power OFF at the disconnect switch or fuse box before working on this equipment.
A-4 INST ALLA TION POWER WAVE® C300 A-4 INPUT CONNECTION On l y a q ua l if i ed el ec t ri c ia n s h ou l d connect the input leads to the POWER WAVE® C300. Connections should be made in accordance with all local and national electrical codes and the connection diagram located on the inside of the reconnect access door of the machine.
A-5 INST ALLA TION POWER WAVE® C300 A-5 RECOMMENDED WORK CABLE SIZES FOR ARC WELDING A 15 ft. work cable is provided with the POWER WAVE® C300. This cable is appropriately sized for all of the POWER WAVE® C300’s welding procedures.
A-6 INST ALLA TION POWER WAVE® C300 A-6 3 3 4 4 2 2 1 1 A A B B C C D D F F E E A A B B G G C C D D F F E E Function 4-pin trigger con- nector for push- only guns.
A-7 INST ALLA TION POWER WAVE® C300 A-7 2. Remove the cylinder cap. Inspect the cylinder valves and regulator for damaged threads, dirt, dust, oil or grease. Remove dust and dirt with a clean cloth. DO NOT ATTACH THE REGULATOR IF OIL, GREASE OR DAMAGE IS PRESENT! Inform your gas supplier of this condition.
A-8 INST ALLA TION POWER WAVE® C300 A-8 LOADING SPOOLS OF WIRE • Keep hands, hair, clothing and tools away from rotating equipment. • Do not wear gloves when threading wire or changing wire spool. • Only qualified personnel should install, use or service this equipment.
A-9 INST ALLA TION POWER WAVE® C300 A-9 WIRE DRIVE CONFIGURA TION (See Figure A.4) Changing the Gun Receiver Bushing ELECTRIC SHOCK can kill. • T u r n t h e i n p u t p o w e r O F F a t t h e welding power source before instal- lation or changing drive rolls and/or guides.
A-10 INST ALLA TION POWER WAVE® C300 A-10 GUN USED The Magnum 300 is the recommended gun for the POWER WAVE® C300. Refer to the Magnum 300’s operators manual for installation instructions. FEEDING ELECTRODE AND BRAKE ADJUSTMENT 1 . Turn the Reel or spool until the free end of the electrode is accessible.
A-11 INST ALLA TION POWER WAVE® C300 A-11 TIG WELDING (Figure A.7) Tig uses Electrode Negative Polarity so for this appli- cation, connect the Tig torch to the negative (-) output stud and connect the work clamp to the positive (+) output stud.
B-1 OPERA TION POWER WAVE® C300 B-1 • ELECTRIC SHOCK CAN KILL. Unless using COLD FEED fea- ture, when feeding with gun trig- g e r , t h e e l e c t r o d e a n d d r i v e mechanism are always electri- cally energized and could remain energized several sec- onds after the welding ceases.
B-2 OPERA TION B-2 PRODUCT DESCRIPTION The Power Wave® C300 is a high performance multi- process machine with GMAW, FCAW, SMAW, DC TIG, and pulse capability. It will offer a premier weld- ing performance solution for specific areas such as aluminum, stainless, nickel where size and weight are an issue.
B-3 OPERA TION B-3 DESIGN FEA TURES Loaded with Standard Features • Multiple process DC output range: 5 - 300 Amps. • 200 – 600 VAC, 1/3 phase, 50-60Hz input power. • New and Improved Line Voltage Compensation holds the output constant over wide inpu t voltage fluctuations.
B-4 OPERA TION B-4 CASE FRONT CONTROLS (Code 11479) All operator controls and adjustments are located on the case front of the Power Wave. (See Figure B.1) 1. LEFT DISPLAY- Shows wire feed speed or amper- age, 2. LEFT KNOB - Adjusts value in left display.
B-5 OPERA TION B-5 POWER WAVE® C300 CASE BACK CONTROLS (Code 11479) 1. ETHERNET CONNECTOR 2. POWER CORD 3. GAS CONNECTION 1 2 3 FIGURE B.2.
B-6 OPERA TION B-6 INTERNAL CONTROLS (Code 11479) 1. SPINDLE BRAKE 2. WIRE DRIVE PRESSURE ARM 3. THUMB SCREW, FOR SECURING THE WELDING GUN 4. GUN BUSHING 5 . SOCKET HEAD CAP SCREW FOR SECURING THE GUN BUSHING 6. 4-PIN TRIGGER RECEPTACLE 7. POSITIVE STUD 8.
B-7 OPERA TION B-7 MAKING A WELD WITH W A VEFORM TECHNOLOGY POWER SOURCES MAKING A WELD The serviceability of a product or structure utilizing the welding programs is and must be the sole responsibility of the builder/user. Many variables beyond the control of The Lincoln Electric Company affect the results obtained in applying these programs.
B-8 OPERA TION B-8 POWER WAVE® C300 ST ART OPTIONS END OPTIONS SETUP IR PORT WELD MODE UltimArc™ Control LESS AMPS MORE AMPS OUTPUT OFF OUTPUT ON + + AMPS WIRE FEED SPEED (WFS) VOL TS TRIM CASE FRO.
B-9 OPERA TION B-9 SMA W (STICK) WELDING SMAW is most often used for outdoor construction, pipe welding and general repairs. The wire feeder controls Amperage, Output Control and Arc Force dur- ing SMAW welding. During SMAW welding the wire drive remains idle.
B-10 OPERA TION B-10 NON-SYNERGIC GMA W AND FCA W WELDING In non-synergic modes, the WFS control is similar to a conventional CV power source where WFS and volt- age are independent adjustments. Therefore to main- tain the arc characteristics, the operator must adjust the voltage to compensate for any changes made to the WFS.
B-11 OPERA TION B-11 GMA W (MIG) SYNERGIC WELDING For each wire feed speed, a corresponding voltage is preprogrammed into the machine. The nominal pre- programmed voltage is the best average voltage for a given wire feed speed, but may be adjusted to prefer- ence.
B-12 OPERA TION B-12 POWER WAVE® C300 STEEL AND ST AINLESS SYNERGIC GMA W-P (PULSED MIG) WELDING T rim .5 0 Arc Length S ho rt T rim 1 .0 0 Arc L e ngth M ed iu m T rim 1 .5 0 Arc L e ngth L ong OF F Me d i u m Fr equ ency an d W i d th +10.0 H i gh F r equen cy , Fo cu s ed UltimArc™ Control - 10 .
B-13 OPERA TION B-13 S T E E L A N D S T A I N L E S S G M AW- P (PULSED MIG) WELDING POWER WAVE® C300 ST ART OPTIONS END OPTIONS SETUP IR PORT WELD MODE UltimArc™ Control Less D eposition More Deposition Shorter Arc Longer Arc + + AMPS WFS VOL TS TRIM 220 1.
B-14 OPERA TION B-14 POWER WAVE® C300 ALUMINUM SYNERGIC GMA W-P (PULSED MIG)AND GMA W -PP (PULSE ON PULSE) WELDING The Power Wave® C300 can produce top quality alu- minum welds with excellent appearance, little spatter and good bead shape. Push-pull guns are available for consistent feeding when welding a long distance away from the wire feeder.
B-15 OPERA TION B-15 POWER WAVE® C300 ALUMINUM GMA W-P (PULSED MIG) AND GMA W -PP (PULSE ON PULSE) WELDING ST ART OPTIONS E ND OPTIONS SETUP I R PORT WELD MODE UltimArc™ Control Less Deposition More Deposition Shorter Arc Longer Arc + + AMPS WFS VOL TS TRIM 220 1.
B-16 OPERA TION B-16 POWER WAVE® C300 GT A W (TIG) WELDING The Power Wave® C300 is excellent for Touch Start TIG welding. ST ART OPTIONS END OPTIONS SETUP IR PORT WELD MODE UltimArc™ Control OUTPUT ON OUTPUT OFF + + AMPS W FS VOL TS TRIM 220 OFF 3 TOUCH ST ART TIG No UltimArc™ Control are active for Touch Start TIG.
B-17 OPERA TION B-17 DUAL PROCEDURE/MEMOR Y P ANEL OPERA TION The Dual Procedure/Memory Panel performs three functions: • Weld procedure selection • Memory save and recall • Limits setting There are two procedure memories ( A and B ) and eight user memories (1-8).
B-18 OPERA TION B-18 To set limits, press the desired memory button 1-8 and hold for 5 seconds. Release the memory button when the LED begins to blink rapidly and the MSP4 displays "Memory X Set Limits" as shown below. POWER WAVE® C300 LIMITS Limits allow the welder to adjust the welding proce- dure only within a defined range.
B-19 OPERA TION B-19 POWER WAVE® C300 If the passcode does not equal zero (0000), enter the passcode now. If the passcode has been forgotten, a p.c. computer application or Palm O.
B-20 OPERA TION B-20 POWER WAVE® C300 2-STEP 4-STEP- TRIG GER OPERA TION The 2-Step - 4-Step switch changes the function of the gun trigger. 2-Step trigger operation switches the welding output ON-OFF in direct response to the trig- ger.
B-21 OPERA TION B-21 POWER WAVE® C300 EXAMPLE 1 - 2 STEP TRIGGER: Simple operation The simplest trigger operation occurs with a 2 Step trigger and the Start, Crater and Burnba ck functions all set to OFF. (See Figure B.11) For this sequence, PREFLOW: Shielding gas begins to flow immediately when the gun trigger is pulled.
B-22 OPERA TION B-22 POWER WAVE® C300 EXAMPLE 2 - 2 STEP TRIGGER: Improved Arc Start and Arc End. Tailoring the arc start and arc end is a common method for reducing spatter and improving weld quality. This can be accomplished with the Start and Burnback functions set to a desired values and Crater set to OFF.
B-23 OPERA TION B-23 POWER WAVE® C300 WELD: After upslope, the power source output and the wire feed speed continue at the weld settings. CRATER & DOWNSLOPE: As soon as the trigger is released, the wire feed speed and power source output ramp to the crater settings throughout the crater time.
B-24 OPERA TION B-24 POWER WAVE® C300 Shield in g G as I dl e Pre fl o w St ri ke We l d Bu rn ba ck Po st f low I dl e WFS On Of f Ru n -i n Of f We l d Of f We l d Arc Established T rigger Pulled T rigger Released 4 St ep T rigg er St art = O FF C rater = OFF Bu rnb ack = OF F 1.
B-25 OPERA TION B-25 POWER WAVE® C300 EXAMPLE 5 - 4 STEP TRIGGER: Manual control of Start and Crater times with Burnback ON. The 4 step trigger sequence gives the most flexibility when the Start, Crater and Burnback functions are active.
B-26 OPERA TION B-26 POWER WAVE® C300 COLD FEED/GAS PURGE SWITCH Cold Feed and Gas Purge are com- bined into a single spring centered tog- gle switch. To activate Cold Feeding, hold the switch in the FORWARD position. The wire drive will feed electrode but neither the power source nor the gas solenoid will be energized.
B-27 OPERA TION B-27 POWER WAVE® C300 SET -UP FEA TURES MENU (See Figure B.16) 1. To access the set-up menu, press the Right and Left buttons of the MSP4 panel simultaneously. Note that the set-up menu cannot be accessed if the system is welding, or if there is a fault (The sta- tus LED is not solid green).
B-28 OPERA TION B-28 POWER WAVE® C300 Parameter Definition Exit Setup Menu P .0 This setup menu parameter can be used to exit the setup menu. When P.0 is displayed, press the left Mode Select button to exit the setup menu. P .1 Wire Feed Speed Units P.
B-29 OPERA TION B-29 POWER WAVE® C300 Parameter Definition P .5 Procedure Change Method Selects how remote procedure selection (A/B) will be made. The selected procedure can be changed locally at the user interface by pressing the 'A-Gun-B' button.
B-30 OPERA TION B-30 POWER WAVE® C300 Parameter Definition P .7 Gun Offset Adjustment Range: -30 to 30 (default = 0) Adjusts the wire feed speed calibration of the pull motor of a push-pull gun. This should only be performed when other possible corrections do not solve any push-pull feeding problems.
B-31 OPERA TION B-31 POWER WAVE® C300 Parameter Definition P .16 Push-Pull Gun Knob Behavior Determines how the potentiometer on the Push/Pull torch will behave. • Gun Pot Enabled = The welding wire feed speed is always controlled by the potentiometer on the push-pull gun (default).
B-32 OPERA TION B-32 POWER WAVE® C300 Parameter Definition P .103 View Software V ersion Information Used for viewing the firmware versions for each board in the system. Press the right MSP Button to enter the option. Rotate Set knob to select the desired board to read.
B-33 OPERA TION B-33 POWER WAVE® C300 Parameter Definition P .503 Memory Button Disable Disables the specified memory button(s). When a memory is disabled, welding procedures can- not be restored from or saved to that memory.
B-34 OPERA TION B-34 POWER WAVE® C300 Parameter Definition P .507 UI Clear All Memories Allows the operator to quickly set all memories to the default weld mode and welding parame- ters.
C-1 ACCESSORIES C-1 OPTIONS / ACCESSORIES STICK OPTIONS K875 ACCESSOR Y KIT - 150 Amp For stick welding. Incl udes 20 ft. (6.1m) #6 electrode cable with lug, 15 ft. (4.6m) #6 work cable with lugs, headshield, filter plate, work clamp, electrode holder and sam- ple pack of mild steel electrode.
C-2 ACCESSORIES C-2 WIRE FEEDER OPTIONS K1703-1 ALUMINUM FEEDING KIT Conversion kit for welding with 3/64 (1.2mm) aluminum wire. Includes ten- sion spring, drive rolls, contact tips (qty.
D-1 MAINTENANCE D-1 POWER WAVE® C300 SAFETY PRECAUTIONS W ARNING ELECTRIC SHOCK can kill. • Do not operate with covers removed. • Turn off power source before installing or servicing. • Do not touch ele ctrically hot parts. • Turn the input power to the welding power source off at the fuse box before working in the terminal strip.
E-1 TROUBLESHOOTING E-1 POWER WAVE® C300 If for any reason you do not understand the test procedures or are unable to perform the tests/repairs safely, contact your Local Lincoln Authorized Field Service Facility for technical troubleshooting assistance before you proceed.
E-2 TROUBLESHOOTING E-2 POWER WAVE® C300 If for any reason you do not understand the test procedures or are unable to perform the tests/repairs safely, contact your Local Lincoln Authorized Field Service Facility for technical troubleshooting assistance before you proceed.
E-3 TROUBLESHOOTING E-3 POWER WAVE® C300 Observe all Safety Guidelines detailed throughout this manual If for any reason you do not understand the test procedures or are unable to perform the tests/repairs safely, contact your Local Lincoln Authorized Field Service Facility for technical troubleshooting assistance before you proceed.
E-4 TROUBLESHOOTING E-4 POWER WAVE® C300 Observe all Safety Guidelines detailed throughout this manual If for any reason you do not understand the test procedures or are unable to perform the tests/repairs safely, contact your Local Lincoln Authorized Field Service Facility for technical troubleshooting assistance before you proceed.
E-5 TROUBLESHOOTING E-5 POWER WAVE® C300 Observe all Safety Guidelines detailed throughout this manual If for any reason you do not understand the test procedures or are unable to perform the tests/repairs safely, contact your Local Lincoln Authorized Field Service Facility for technical troubleshooting assistance before you proceed.
E-6 TROUBLESHOOTING E-6 POWER WAVE® C300 Observe all Safety Guidelines detailed throughout this manual If for any reason you do not understand the test procedures or are unable to perform the tests/repairs safely, contact your Local Lincoln Authorized Field Service Facility for technical troubleshooting assistance before you proceed.
E-7 TROUBLESHOOTING E-7 POWER WAVE® C300 Observe all Safety Guidelines detailed throughout this manual If for any reason you do not understand the test procedures or are unable to perform the tests/repairs safely, contact your Local Lincoln Authorized Field Service Facility for technical troubleshooting assistance before you proceed.
E-8 TROUBLESHOOTING E-8 POWER WAVE® C300 Observe all Safety Guidelines detailed throughout this manual If for any reason you do not understand the test procedures or are unable to perform the tests/repairs safely, contact your Local Lincoln Authorized Field Service Facility for technical troubleshooting assistance before you proceed.
F-1 DIAGRAMS F-1 POWER WAVE® C300 NOTE: This diagram is for reference only. It may not be accurate for all machines covered by this manual. The specific diagram for a particular code is pasted inside the machine on one of the enclosure panels. If the diagram is illegible, write to the Service Department for a replacement.
F-2 DIMENSION PRINT F-2 POWER WAVE® C300.
NOTES POWER WAVE® C300.
W ARNING A VISO DE PRECAUCION A TTENTION W ARNUNG A TENÇÃO Spanish French German Portuguese Japanese Chinese Korean Arabic READ AND UNDERST AND THE MANUFACTURER’S INSTRUCTION FOR THIS EQUIPM ENT AND THE CONSUMABLES TO BE USED AND FOLLOW YOUR EMPLOYER’S SAFETY PRACTICES.
W ARNING A VISO DE PRECAUCION A TTENTION W ARNUNG A TENÇÃO Spanish French German Portuguese Japanese Chinese Korean Arabic LEIA E COMPREENDA AS INSTRUÇÕES DO F ABRICANTE P ARA ESTE EQUIPAMENTO E AS P ARTES DE USO, E SIGA AS PRÁTICAS DE SEGURANÇA DO EMPREGADOR.
• Sales and Service through Subsidiaries and Distributors Worldwide • Cleveland, Ohio 44117-1199 U.S.A. TEL: 216.481.8100 FAX: 216.486.1751 WEB SITE: www.
デバイスLincoln Electric IM956-Aの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Lincoln Electric IM956-Aをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはLincoln Electric IM956-Aの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Lincoln Electric IM956-Aの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Lincoln Electric IM956-Aで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Lincoln Electric IM956-Aを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はLincoln Electric IM956-Aの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Lincoln Electric IM956-Aに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちLincoln Electric IM956-Aデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。