Lincoln ElectricメーカーPOWER SOURCE IM640-Aの使用説明書/サービス説明書
ページ先へ移動 of 37
OPERA T OR’S MANUAL S AE400 & S AE400 WELD’N AIR - DC ARC WELDING PO WER SOURCE IM640-A May , 2004 For use with machines having Code Numbers: 10601, 10602, 10884, 10885 Safety Depends on Y ou Lincoln arc welding and cutting equipment is designed and built with safety in mind.
FOR ENGINE powered equipment. 1.a. T urn the engine off before troubleshooting and maintenance work unless the maintenance work requires it to be running. ____________________________________________________ 1.b. Operate engines in open, well-ventilated areas or vent the engine exhaust fumes outdoors.
ii SAFETY ii ARC RA YS can burn. 4.a. Use a shield with the proper filter and cover plates to protect your eyes from sparks and the rays of the arc when welding or observing open arc welding. Headshield and filter lens should conform to ANSI Z87. I standards.
iii SAFETY iii FOR ELECTRICALL Y powered equipment. 8.a. T urn off input power using the disconnect switch at the fuse box before working on the equipment. 8.b. Install equipment in accordance with the U.S. National Electrical Code, all local codes and the manufacturer ’s recommendations.
iv SAFETY iv Mar . ‘93 PRÉCAUTIONS DE SÛRETÉ Pour votre propre protection lire et observer toutes les instructions et les précautions de sûreté specifiques qui parraissent dans ce manuel aussi bien que les précautions de sûreté générales suiv- antes: Sûreté Pour Soudage A L ’Arc 1.
v SAFETY v W ARNING Assure that tank and compressor relief valves w ork properl y , and are at correct pressure settings. NEVER move compressor with pressure in tank.
vi SAFETY vi.
vii vii Thank You for selecting a QUALITY product by Lincoln Electric. We want you to take pride in operating this Lincoln Electric Company product ••• as much pride as we have in bringing this product to you! Read this Operators Manual completely before attempting to use this equipment.
viii T ABLE OF CONTENTS SAE400 & SAE400 WELD ’ N AIR viii Page Installation Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Section A T echnical Specifications . . . . . . . . . . . . . . . . .
A-1 INST ALLA TION SAE400 & SAE400 WELD ’ N AIR A-1 TECHNICAL SPECIFICA TIONS - SAE400 & SAE400 WELD ’ N AIR Make/Model Description Speed (RPM) Displacement Starting Capacities System Perkins 4 cylinder High Idle 1800 256 cu. in 12VDC batteries Fuel: 22.
A-2 INST ALLA TION SAE400 & SAE400 WELD ’ N AIR A-2 Read this entire installation section before you start installation. SAFETY PRECAUTIONS Do not attempt to use this equipment until you have thoroughly read all operating and maintenance man- uals supplied with your machine.
A-3 INST ALLA TION SAE400 & SAE400 WELD ’ N AIR A-3 HIGH AL TITUDE OPERA TION At higher altitudes, output derating may be necessary . As a rule of thumb, derate the welder output 5% for every 500 meters (1640 ft.
A-4 INST ALLA TION A-4 SAE400 & SAE400 WELD ’ N AIR • Stop engine while fueling. • Do not smoke when fueling. • Keep sparks and flame away from tank. • Do not leave unattended while fueling. • W ipe up spilled fuel and allow fumes to clear before starting engine.
BA TTERY ACID can burn eyes and skin. ● Wear gloves and eye protection and be careful when working near battery . ● Follow instructions printed on battery . IMPORT ANT : T o prevent ELECTRICAL DAMAGE WHEN: a) Installing new batteries. b) Using a booster .
B-1 OPERA TION B-1 WELDING SP ARKS can cause fire or explosion. • Do not weld near flammable material . • Do not weld on containers that have held flammable material. ----------------------------------------------------------- MOVING P ARTS can injure.
B-2 OPERA TION B-2 RECOMMENDED APPLICA TIONS WELDER The SAE400 or SAE400 WELD’N AIR provides excel- lent constant current DC welding output for stick (SMA W) welding. The field installed optional CV Adapter (K385-1) provides up to 500 amps at 35 volts of constant voltage output for semiautomatic welding.
B-3 OPERA TION B-3 ENGINE CONTROLS IGNITION SWITCH When placed in the “ON” position, this switch ener- gizes the fuel solenoid. When placed in the “OFF” posi- tion, the flow of fuel to the injection pump is stopped to shut down the engine. “ IDLER ” SWITCH The idler switch has two positions, “HIGH” and “AUTO”.
B-4 OPERA TION B-4 How to Set the Controls Assume you want a normal soft arc and about 135 amps, using a 5/32” (4.0 mm) electrode: 1. Set the “Job Selector” at the center of the black range. 2. Set the “Current Control” to read 135 amps on the black dial.
B-5 OPERA TION B-5 ENGINE OPERA TION Do not adjust the high idle engine speed (rpm) above the factory setting specification as this will overspeed the air compressor and void it’s warranty . ------------------------------------------------------------------------ ST ARTING INSTRUCTIONS Be sure all Pre-Operation Maintenance has been per- formed.
C-1 ACCESSORIES C-1 K930-2 Hi-Freq ™ - Provides high frequency plus a gas valve for TIG welding. A water valve is available as an option. Requires 1 15 volt AC input. (Limited to 250A - 60% Duty Cycle). K802-D Power Plug Kit - Kit includes male plugs for each auxiliary receptacle.
D-1 MAINTENANCE D-1 ELECTRIC SHOCK can kill. ● Do not touch electrically live parts such as output terminals or inter- nal wiring ENGINE EXHAUST can kill.
D-2 MAINTENANCE D-2 COMMUT A TOR AND BRUSH MAINTENANCE Uncovered rotating equipment can be dangerous. Use care so your hands, hair , clothing or tools do not catch in the rotating parts. Protect yourself from particles that may be thrown out by the rotat- ing armature when stoning the commutator .
D-3 MAINTENANCE D-3 4. Using a pair of pliers, gently tug on the pull tabs of the pre-filter screen in an alternating pattern to gradually remove the pre-filter screen. 5. Brush of f any debris and rinse in diesel fuel. 6. Re-install the pre-filter screen into the upper cavity of the filter header making sure the four pull tabs are pointing up.
D-4 MAINTENANCE D-4 SP ARK ARRESTOR • Spark Arrester and Muffler may be hot! • Allow engine to cool before servicing spark arrester! • Do not operate engine while servicing spark arrester! For machines with separate spark arresting units: Service the spark arrestor every 100 hours of opera- tion or twice a year , which ever occurs first.
E-1 TROUBLESHOOTING E-1 SAE400 & SAE400 WELD ’ N AIR If for any reason you do not understand the test procedures or are unable to perform the tests/repairs safely , contact your Local Lincoln Authorized Field Service Facility for technical troubleshooting assistance before you proceed.
E-2 TROUBLESHOOTING E-2 SAE400 & SAE400 WELD ’ N AIR Observe all Safety Guidelines detailed throughout this manual If for any reason you do not understand the test procedures or are unable to pe.
E-3 TROUBLESHOOTING E-3 SAE400 & SAE400 WELD ’ N AIR Observe all Safety Guidelines detailed throughout this manual If for any reason you do not understand the test procedures or are unable to pe.
E-4 TROUBLESHOOTING E-4 SAE400 & SAE400 WELD ’ N AIR Observe all Safety Guidelines detailed throughout this manual If for any reason you do not understand the test procedures or are unable to pe.
E-5 TROUBLESHOOTING E-5 SAE400 & SAE400 WELD ’ N AIR Observe all Safety Guidelines detailed throughout this manual If for any reason you do not understand the test procedures or are unable to pe.
F-1 WIRING DIAGRAMS SAE400 & SAE400 WELD ’ N AIR F-1 B 239 Enable TERMINAL Compressor IGNITE R COLD B 233 THER MOSTART B B - START THER MOSTART 230 W 30 B B 229 B 234 220 B B IDLER SWITCH IND J2 PROTECTI ON P.C. BOA RD IDLER/ENGINE J1 + TO TORO ID 2 CR REED RELAY R GROUND SCREW B STARTING Pressure SW.
SAE400 & SAE400 WELD ’ N AIR F-2 WIRING DIAGRAMS F-2 SWITCH PROTECTI ON P.C. BOA RD IDLER/ENGINE J1 + SW ITCH (N.C.) OIL PRESSUR E THERMOSTART COLD TERMINAL START B - THERMOSTART 5C B B + GROUND.
SAE400 & SAE400 WELD ’ N AIR F-3 WIRING DIAGRAMS F-3 7- 01 M19 237 COLOR CODE ALTERNATOR ROTOR AC + SLIP - RINGS (-) D2 FLASHIN G DIODE B-BLACK OR GRAY G-GREEN N-BROWN R-RED OR PINK U-BLUE W-WHI.
SAE400 & SAE400 WELD ’ N AIR F-4 DIMENSION PRINT F-4 18.50 22.14 22.00 27.12 24.50 8.12 3.00 .88 43.75 63.06 39.69 50.13 28.00 32.87 6.00 81.25 69.75 77.00 39.38 44.50 8.90 83.00 * = .81 DIA HOLES = .69 DIA HOLES * * CENTER OF GRAVITY WITH OIL AND WATER IN ENGINE, BUT NO FUEL.
SAE400 & SAE400 WELD ’ N AIR NOTES.
SAE400 & SAE400 WELD ’ N AIR W ARNING A VISO DE PRECAUCION A TTENTION W ARNUNG A TEN ÇÃ O Spanish French German Portuguese Japanese Chinese Korean Arabic LEIA E COMPREENDA AS INSTRUÇÕES DO F ABRICANTE PARA ESTE EQUIP AMENTO E AS P ARTES DE USO, E SIGA AS PRÁTICAS DE SEGURANÇA DO EMPREGADOR.
SAE400 & SAE400 WELD ’ N AIR W ARNING A VISO DE PRECAUCION A TTENTION W ARNUNG A TEN ÇÃ O Spanish French German Portuguese Japanese Chinese Korean Arabic READ AND UNDERST AND THE MANUF ACTURER’S INSTRUCTION FOR THIS EQUIPMENT AND THE CONSUMABLES TO BE USED AND FOLLOW YOUR EMPLOYER’S SAFETY PRACTICES.
• Sales and Service through Subsidiaries and Distributors Worldwide • Cleveland, Ohio 441 17-1 199 U.S.A. TEL: 216.481.8100 F AX: 216.486.1751 WEB SITE: www .
デバイスLincoln Electric POWER SOURCE IM640-Aの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Lincoln Electric POWER SOURCE IM640-Aをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはLincoln Electric POWER SOURCE IM640-Aの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Lincoln Electric POWER SOURCE IM640-Aの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Lincoln Electric POWER SOURCE IM640-Aで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Lincoln Electric POWER SOURCE IM640-Aを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はLincoln Electric POWER SOURCE IM640-Aの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Lincoln Electric POWER SOURCE IM640-Aに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちLincoln Electric POWER SOURCE IM640-Aデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
