Lincoln ElectricメーカーSVM165-Aの使用説明書/サービス説明書
ページ先へ移動 of 128
PO WER MIG ™ 350MP SER VICE MANUAL SVM165-A January . 2006 Safety Depends on You Lincoln arc welding and cutting equipment is designed and built with safety in mind. However, your overall safety can be increased by proper installation ... and thought- ful operation on your part.
i i Return to Master TOC Return to Master TOC Return to Master TOC Return to Master TOC FOR ENGINE powered equipment. 1.a. Turn the engine off before troubleshooting and maintenance work unless the maintenance work requires it to be running. ____________________________________________________ 1.
SAFETY ii ii Return to Master TOC Return to Master TOC Return to Master TOC Return to Master TOC ARC RA YS can burn. 4.a. Use a shield with the proper filter and cover plates to protect your eyes from sparks and the rays of the arc when welding or observing open arc welding.
SAFETY iii iii POWER MIG 350MP Return to Master TOC Return to Master TOC Return to Master TOC Return to Master TOC FOR ELECTRICALL Y powered equipment. 8.a. Turn off input power using the disconnect switch at the fuse box before working on the equipment.
POWER MIG 350MP Return to Master TOC Return to Master TOC Return to Master TOC Return to Master TOC iv SAFETY iv PRÉCAUTIONS DE SÛRETÉ Pour votre propre protection lire et observer toutes les instr.
6 6 MASTER T ABLE OF CONTENTS FOR ALL SECTIONS Page Safety .................................................................................................................................................i-iv Installation .............................
A-1 A-1 T ABLE OF CONTENTS - INST ALLA TION SECTION - INSTALLATION ...................................................................................................................... Section A Technical Specifications ..............................
A-2 A-2 INST ALLA TION Return to Section TOC Return to Section TOC Return to Section TOC Return to Section TOC Return to Master TOC Return to Master TOC Return to Master TOC Return to Master TOC Input.
A-3 A-3 INST ALLA TION Return to Section TOC Return to Section TOC Return to Section TOC Return to Section TOC Return to Master TOC Return to Master TOC Return to Master TOC Return to Master TOC ONL Y QUALIFIED PERSONNEL SHOULD INST ALL, USE OR SERVICE THIS EQUIP- MENT .
A-4 A-4 INST ALLA TION Return to Section TOC Return to Section TOC Return to Section TOC Return to Section TOC Return to Master TOC Return to Master TOC Return to Master TOC Return to Master TOC FIGURE A.2 — RECEPTACLE DIAGRAM CONNECT TO A SYSTEM GROUNDING WIRE.
A-5 GUN AND CABLE INST ALLA TION A Magnum 300 gun and 15Ft.(4.6m) cable (12Ft.(3.7m) for Codes 11000 and below) are provid- ed with the Power MIG 350MP. A Magnum cable liner for .035-.045" (0.9-1.2 mm) electrode and contact tips for .035” (0.9mm) and .
A-6 A-6 POWER MIG 350MP Return to Section TOC Return to Section TOC Return to Section TOC Return to Section TOC Return to Master TOC Return to Master TOC Return to Master TOC Return to Master TOC INST ALLA TION DO NOT ATTACH THE REGULATOR IF OIL, GREASE OR DAMAGE IS PRESENT! Inform your gas supplier of this condition.
POWER MIG 350MP Return to Master TOC Return to Master TOC Return to Master TOC Return to Master TOC B-1 B-1 T ABLE OF CONTENTS - OPERA TION SECTION - Operation ...........................................................................................
POWER MIG 350MP Return to Section TOC Return to Section TOC Return to Section TOC Return to Section TOC Return to Master TOC Return to Master TOC Return to Master TOC Return to Master TOC B-2 B-2 OPER.
POWER MIG 350MP Return to Section TOC Return to Section TOC Return to Section TOC Return to Section TOC Return to Master TOC Return to Master TOC Return to Master TOC Return to Master TOC B-3 B-3 OPERA TION PRODUCT DESCRIPTION The Power MIG 350MP is a complete semiautomatic multi-process DC arc welding machine offering CV and CC DC welding.
POWER MIG 350MP Return to Section TOC Return to Section TOC Return to Section TOC Return to Section TOC Return to Master TOC Return to Master TOC Return to Master TOC Return to Master TOC 5. MULTI-PROCESS PANEL - This panel enables selection of weld modes as well as adjustment of certain weld parameters within each weld mode.
POWER MIG 350MP Return to Section TOC Return to Section TOC Return to Section TOC Return to Section TOC Return to Master TOC Return to Master TOC Return to Master TOC Return to Master TOC B-5 B-5 OPER.
POWER MIG 350MP Return to Section TOC Return to Section TOC Return to Section TOC Return to Section TOC Return to Master TOC Return to Master TOC Return to Master TOC Return to Master TOC B-6 B-6 OPER.
Return to Section TOC Return to Section TOC Return to Section TOC Return to Section TOC Return to Master TOC Return to Master TOC Return to Master TOC Return to Master TOC B-7 B-7 OPERA TION POWER MIG 350MP Arc Control (See Table B.
Return to Section TOC Return to Section TOC Return to Section TOC Return to Section TOC Return to Master TOC Return to Master TOC Return to Master TOC Return to Master TOC B-8 B-8 OPERA TION POWER MIG.
Return to Section TOC Return to Section TOC Return to Section TOC Return to Section TOC Return to Master TOC Return to Master TOC Return to Master TOC Return to Master TOC B-9 B-9 OPERA TION POWER MIG 350MP 5. Rotate the spindle and adapter so the retaining spring is at the 12 o'clock position.
POWER MIG 350MP Return to Section TOC Return to Section TOC Return to Section TOC Return to Section TOC Return to Master TOC Return to Master TOC Return to Master TOC Return to Master TOC B-10 B-10 OPERA TION 4.
Return to Section TOC Return to Section TOC Return to Section TOC Return to Section TOC Return to Master TOC Return to Master TOC Return to Master TOC Return to Master TOC B-11 B-11 OPERA TION POWER M.
B-12 B-12 OPERA TION Return to Section TOC Return to Section TOC Return to Section TOC Return to Section TOC Return to Master TOC Return to Master TOC Return to Master TOC Return to Master TOC POWER M.
Return to Section TOC Return to Section TOC Return to Section TOC Return to Section TOC Return to Master TOC Return to Master TOC Return to Master TOC Return to Master TOC B-13 B-13 OPERA TION POWER M.
B-14 NOTES POWER MIG 350MP B-14 Return to Section TOC Return to Section TOC Return to Section TOC Return to Section TOC Return to Master TOC Return to Master TOC Return to Master TOC Return to Master .
POWER MIG 350MP C-1 C-1 T ABLE OF CONTENTS - ACCESSORIES - Accessories ........................................................................................................................... Section C Drive Roll Kits ..............................
C-2 C-2 ACCESSORIES POWER MIG 350MP DRIVE ROLL KITS Refer to Table C.1 for various drive roll kits that are available for the Power MIG. All items in Bold are supplied standard with the Power MIG. TABLE C.1 * .035 Aluminum recommended for Push-Pull systems only.
C-3 C-3 ACCESSORIES MIG 350MP does not control the WFS at the spool gun. Rather, it is adjusting the Power MIG 350MP synergic work point. Therefore, adjusting the SPD value will not change your actual WFS at the spool gun. WFS can only be changed at the spool gun.
C-4 C-4 NOTES POWER MIG 350MP Return to Section TOC Return to Section TOC Return to Section TOC Return to Section TOC Return to Master TOC Return to Master TOC Return to Master TOC Return to Master TO.
POWER MIG 350MP D-1 D-1 T ABLE OF CONTENTS -MAINTENANCE- Maintenance .......................................................................................................................... Section D Safety Precautions & General Maintenance ....
MAINTENANCE D-2 D-2 POWER MIG 350MP Return to Section TOC Return to Section TOC Return to Section TOC Return to Section TOC Return to Master TOC Return to Master TOC Return to Master TOC Return to Master TOC CONT ACT TIP AND GAS NOZZLE INST ALLA TION a.
D-3 D-3 MAINTENANCE 5. Seat Liner bushing into back of gun. Secure Liner by tightening set screw. Do not install the gas dif- fuser at this time. 6 . Lay the cable straight and trim Liner to 9/16”. Remove burrs. 7. Secure the gas diffuser into the tube.
D-4 D-4 MAINTENANCE POWER MIG 350MP Return to Section TOC Return to Section TOC Return to Section TOC Return to Section TOC Return to Master TOC Return to Master TOC Return to Master TOC Return to Master TOC 1 2 6 5 3 4 1. Case Front Assembly 2. Center Assembly 3.
Return to Master TOC Return to Master TOC Return to Master TOC Return to Master TOC Section E-1 Section E-1 POWER MIG 350MP Theory of Operation ...........................................................................................................
Return to Section TOC Return to Section TOC Return to Section TOC Return to Section TOC Return to Master TOC Return to Master TOC Return to Master TOC Return to Master TOC GENERAL DESCRIPTION The Power MIG 350MP is a complete semiautomatic, multi-process DC arc welding machine offering CV and CC DC welding.
Return to Section TOC Return to Section TOC Return to Section TOC Return to Section TOC Return to Master TOC Return to Master TOC Return to Master TOC Return to Master TOC INPUT VOL T AGE AND MAIN TRANS- FORMER Single-phase input power is brought into the rear of the Power MIG 350MP through a three-prong plug and input cable.
THEOR Y OF OPERA TION E-4 E-4 POWER MIG 350MP Return to Section TOC Return to Section TOC Return to Section TOC Return to Section TOC Return to Master TOC Return to Master TOC Return to Master TOC Ret.
DIODE CONTROL RECTIFIER AND POWER BOARD The Power Board receives approximately 40 VDC from the Diode Control Rectifier . In turn, the Power Board supplies a variety of regulated DC voltages to the Weld Control Board, which it uses to power its many circuits and communication functions.
WELD CONTROL BOARD The Weld Control Board performs the primary interfac- ing functions to establish and maintain output control of the Power MIG 350MP machine. The function genera- tor and weld files reside within the Weld Control Board hardware and software.
E-7 E-7 POWER MIG 350MP Return to Section TOC Return to Section TOC Return to Section TOC Return to Section TOC Return to Master TOC Return to Master TOC Return to Master TOC Return to Master TOC WIRE DRIVE MOT OR AND FEED- BACK The Wire Drive Motor is controlled by the Feeder Board and the Weld Control Board.
THERMAL PROTECTION T wo normally closed (NC) thermostats protect the machine from excessive operating temperatures. These thermostats are wired in series and are con- nected to the Weld Control Board. One of the ther- mostats is located on the Chopper Assembly Board, and one is on the secondary of the Main T ransformer .
Return to Section TOC Return to Section TOC Return to Section TOC Return to Section TOC Return to Master TOC Return to Master TOC Return to Master TOC Return to Master TOC THEOR Y OF OPERA TION E-9 E-9 POWER MIG 350MP FIGURE E.
PULSE WIDTH MODULA TION The term PULSE WIDTH MODULA TION is used to describe how much time is devoted to conduction in the positive and negative portions of the cycle.
CHOPPER TECHNOLOGY FUNDAMENT ALS The new era of welding machines such as the Power MIG 350MP employ a technology whereby a DC source is turned on and off (chopped up) at high speed, then smoothed through an inductor to control an arc. Hence the name “Chopper .
Return to Section TOC Return to Section TOC Return to Section TOC Return to Section TOC Return to Master TOC Return to Master TOC Return to Master TOC Return to Master TOC NOTES E-12 E-12 POWER MIG 35.
Return to Master TOC Return to Master TOC Return to Master TOC Return to Master TOC Section F-1 Section F-1 POWER MIG 350MP T roubleshooting & Repair Section ................................................................................ Section F How to Use T roubleshooting Guide .
Return to Section TOC Return to Section TOC Return to Section TOC Return to Section TOC Return to Master TOC Return to Master TOC Return to Master TOC Return to Master TOC HOW T O USE TROUBLESHOOTING GUIDE Service and repair should be performed by only Lincoln Electric Factory T rained Personnel.
POWER MIG 350MP Return to Section TOC Return to Section TOC Return to Section TOC Return to Section TOC Return to Master TOC Return to Master TOC Return to Master TOC Return to Master TOC TROUBLESHOOTING & REP AIR F-3 F-3 Sometimes machine failures appear to be due to PC Board failures.
Return to Section TOC Return to Section TOC Return to Section TOC Return to Section TOC Return to Master TOC Return to Master TOC Return to Master TOC Return to Master TOC TROUBLESHOOTING & REP AI.
Return to Section TOC Return to Section TOC Return to Section TOC Return to Section TOC Return to Master TOC Return to Master TOC Return to Master TOC Return to Master TOC TROUBLESHOOTING & REP AIR F-5 F-5 POWER MIG 350MP TROUBLESHOOTING GUIDE Observe Safety Guidelines detailed in the beginning of this manual.
Return to Section TOC Return to Section TOC Return to Section TOC Return to Section TOC Return to Master TOC Return to Master TOC Return to Master TOC Return to Master TOC TROUBLESHOOTING & REP AI.
Return to Section TOC Return to Section TOC Return to Section TOC Return to Section TOC Return to Master TOC Return to Master TOC Return to Master TOC Return to Master TOC TROUBLESHOOTING & REP AIR F-7 F-7 POWER MIG 350MP TROUBLESHOOTING GUIDE Observe Safety Guidelines detailed in the beginning of this manual.
F-8 F-8 POWER MIG 350MP Return to Section TOC Return to Section TOC Return to Section TOC Return to Section TOC Return to Master TOC Return to Master TOC Return to Master TOC Return to Master TOC TROU.
Return to Section TOC Return to Section TOC Return to Section TOC Return to Section TOC Return to Master TOC Return to Master TOC Return to Master TOC Return to Master TOC TROUBLESHOOTING & REP AI.
Return to Section TOC Return to Section TOC Return to Section TOC Return to Section TOC Return to Master TOC Return to Master TOC Return to Master TOC Return to Master TOC TROUBLESHOOTING & REP AI.
Return to Section TOC Return to Section TOC Return to Section TOC Return to Section TOC Return to Master TOC Return to Master TOC Return to Master TOC Return to Master TOC F-11 F-11 POWER MIG 350MP TR.
Return to Section TOC Return to Section TOC Return to Section TOC Return to Section TOC Return to Master TOC Return to Master TOC Return to Master TOC Return to Master TOC F-12 F-12 POWER MIG 350MP TR.
Return to Section TOC Return to Section TOC Return to Section TOC Return to Section TOC Return to Master TOC Return to Master TOC Return to Master TOC Return to Master TOC TROUBLESHOOTING & REP AI.
Return to Section TOC Return to Section TOC Return to Section TOC Return to Section TOC Return to Master TOC Return to Master TOC Return to Master TOC Return to Master TOC TROUBLESHOOTING & REP AI.
F-15 F-15 POWER MIG 350MP Return to Section TOC Return to Section TOC Return to Section TOC Return to Section TOC Return to Master TOC Return to Master TOC Return to Master TOC Return to Master TOC TR.
CHOPPER BOARD CAP ACIT OR DISCHARGE PROCEDURE Service and repair should be performed by only Lincoln Electric factory trained personnel. Unauthorized repairs performed on this equipment may result in danger to the technician or machine operator and will invalidate your factory warranty .
TROUBLESHOOTING & REP AIR F-17 F-17 POWER MIG 350MP Return to Section TOC Return to Section TOC Return to Section TOC Return to Section TOC Return to Master TOC Return to Master TOC Return to Master TOC Return to Master TOC CHOPPER BOARD CAP ACIT OR DISCHARGE PROCEDURE (continued) FIGURE F .
MAIN TRANSFORMER TEST Service and repair should be performed by only Lincoln Electric factory trained personnel. Unauthorized repairs performed on this equipment may result in danger to the technician or machine operator and will invalidate your factory warranty .
Return to Section TOC Return to Section TOC Return to Section TOC Return to Section TOC Return to Master TOC Return to Master TOC Return to Master TOC Return to Master TOC TROUBLESHOOTING & REP AIR F-19 F-19 POWER MIG 350MP MAIN TRANSFORMER TEST (continued) FIGURE F .
CHOPPER BOARD TEST Service and repair should be performed by only Lincoln Electric factory trained personnel. Unauthorized repairs performed on this equipment may result in danger to the technician or machine operator and will invalidate your factory warranty .
Return to Section TOC Return to Section TOC Return to Section TOC Return to Section TOC Return to Master TOC Return to Master TOC Return to Master TOC Return to Master TOC TROUBLESHOOTING & REP AIR F-21 F-21 POWER MIG 350MP CHOPPER BOARD TEST (continued) FIGURE F .
TROUBLESHOOTING & REP AIR F-22 F-22 POWER MIG 350MP Return to Section TOC Return to Section TOC Return to Section TOC Return to Section TOC Return to Master TOC Return to Master TOC Return to Master TOC Return to Master TOC CHOPPER BOARD TEST (continued) FIGURE F .
CONTROL RECTIFIER TEST Service and repair should be performed by only Lincoln Electric factory trained personnel. Unauthorized repairs performed on this equipment may result in danger to the technician or machine operator and will invalidate your factory warranty .
TROUBLESHOOTING & REP AIR F-24 F-24 POWER MIG 350MP Return to Section TOC Return to Section TOC Return to Section TOC Return to Section TOC Return to Master TOC Return to Master TOC Return to Master TOC Return to Master TOC CONTROL RECTIFIER TEST (continued) FIGURE F .
OUTPUT RECTIFIER ASSEMBL Y TEST Service and repair should be performed by only Lincoln Electric factory trained personnel. Unauthorized repairs performed on this equipment may result in danger to the technician or machine operator and will invalidate your factory warranty .
Return to Section TOC Return to Section TOC Return to Section TOC Return to Section TOC Return to Master TOC Return to Master TOC Return to Master TOC Return to Master TOC TROUBLESHOOTING & REP AIR F-26 F-26 POWER MIG 350MP OUTPUT RECTIFIER ASSEMBL Y TEST (continued) FIGURE F .
WIRE DRIVE MOT OR AND T ACHOMETER FEEDBACK TEST Service and repair should be performed by only Lincoln Electric factory trained personnel. Unauthorized repairs performed on this equipment may result in danger to the technician or machine operator and will invalidate your factory warranty .
Return to Section TOC Return to Section TOC Return to Section TOC Return to Section TOC Return to Master TOC Return to Master TOC Return to Master TOC Return to Master TOC TROUBLESHOOTING & REP AIR F-28 F-28 POWER MIG 350MP WIRE DRIVE MOT OR AND T ACHOMETER FEEDBACK TEST (continued) FIGURE F .
Return to Section TOC Return to Section TOC Return to Section TOC Return to Section TOC Return to Master TOC Return to Master TOC Return to Master TOC Return to Master TOC TROUBLESHOOTING & REP AI.
ENCODER PC BOARD TEST Service and repair should be performed by only Lincoln Electric factory trained personnel. Unauthorized repairs performed on this equipment may result in danger to the technician or machine operator and will invalidate your factory warranty .
F-31 F-31 POWER MIG 350MP Return to Section TOC Return to Section TOC Return to Section TOC Return to Section TOC Return to Master TOC Return to Master TOC Return to Master TOC Return to Master TOC TROUBLESHOOTING & REP AIR ENCODER PC BOARD TEST (continued) G3884 J82 3243 J85 858 857 855 851 1 8510 859 FIGURE F .
TROUBLESHOOTING & REP AIR F-32 F-32 POWER MIG 350MP Return to Section TOC Return to Section TOC Return to Section TOC Return to Section TOC Return to Master TOC Return to Master TOC Return to Mast.
CURRENT TRANSDUCER TEST Service and repair should be performed by only Lincoln Electric factory trained personnel. Unauthorized repairs performed on this equipment may result in danger to the technician or machine operator and will invalidate your factory warranty .
TROUBLESHOOTING & REP AIR F-34 F-34 POWER MIG 350MP Return to Section TOC Return to Section TOC Return to Section TOC Return to Section TOC Return to Master TOC Return to Master TOC Return to Master TOC Return to Master TOC CURRENT TRANSDUCER TEST (continued) FIGURE F .
TROUBLESHOOTING & REP AIR F-35 F-35 POWER MIG 350MP Return to Section TOC Return to Section TOC Return to Section TOC Return to Section TOC Return to Master TOC Return to Master TOC Return to Master TOC Return to Master TOC CURRENT TRANSDUCER TEST (continued) T able F .
POWER MIG 350MP SCROLLING DASHES TEST Service and repair should be performed by only Lincoln Electric factory trained personnel. Unauthorized repairs performed on this equipment may result in danger to the technician or machine operator and will invalidate your factory warranty .
TROUBLESHOOTING & REP AIR F-37 F-37 POWER MIG 350MP Return to Section TOC Return to Section TOC Return to Section TOC Return to Section TOC Return to Master TOC Return to Master TOC Return to Master TOC Return to Master TOC POWER MIG 350MP SCROLLING DASHES TEST (continued) TEST PROCEDURES: 1.
Return to Section TOC Return to Section TOC Return to Section TOC Return to Section TOC Return to Master TOC Return to Master TOC Return to Master TOC Return to Master TOC TROUBLESHOOTING & REP AIR F-38 F-38 POWER MIG 350MP This is a typical DC output voltage waveform generated from a properly operating machine.
Return to Section TOC Return to Section TOC Return to Section TOC Return to Section TOC Return to Master TOC Return to Master TOC Return to Master TOC Return to Master TOC TROUBLESHOOTING & REP AIR F-39 F-39 POWER MIG 350MP SCOPE SETTINGS V olts/Div .
MOT OR & GEAR BOX ASSEMBL Y REMOV AL AND REPLACEMENT Service and repair should be performed by only Lincoln Electric factory trained personnel. Unauthorized repairs performed on this equipment may result in danger to the technician or machine operator and will invalidate your factory warranty .
Return to Section TOC Return to Section TOC Return to Section TOC Return to Section TOC Return to Master TOC Return to Master TOC Return to Master TOC Return to Master TOC TROUBLESHOOTING & REP AIR F-41 F-41 POWER MIG 350MP MOT OR & GEAR BOX ASSEMBL Y REMOV AL AND REPLACEMENT (continued) REMOV AL PROCEDURE ELECTRIC SHOCK can kill .
TROUBLESHOOTING & REP AIR F-42 F-42 POWER MIG 350MP Return to Section TOC Return to Section TOC Return to Section TOC Return to Section TOC Return to Master TOC Return to Master TOC Return to Master TOC Return to Master TOC MOT OR & GEAR BOX ASSEMBL Y REMOV AL AND REPLACEMENT (continued) REPLACEMENT PROCEDURE 1.
TROUBLESHOOTING & REP AIR F-43 F-43 POWER MIG 350MP Return to Section TOC Return to Section TOC Return to Section TOC Return to Section TOC Return to Master TOC Return to Master TOC Return to Master TOC Return to Master TOC MOT OR & GEAR BOX ASSEMBL Y REMOV AL AND REPLACEMENT (continued) FIGURE F .
OUTPUT RECTIFIER REMOV AL AND REPLACEMENT Service and repair should be performed by only Lincoln Electric factory trained personnel. Unauthorized repairs performed on this equipment may result in danger to the technician or machine operator and will invalidate your factory warranty .
TROUBLESHOOTING & REP AIR F-45 F-45 POWER MIG 350MP Return to Section TOC Return to Section TOC Return to Section TOC Return to Section TOC Return to Master TOC Return to Master TOC Return to Master TOC Return to Master TOC OUTPUT RECTIFIER REMOV AL AND REPLACEMENT (continued) ELECTRIC SHOCK can kill .
TROUBLESHOOTING & REP AIR F-46 F-46 POWER MIG 350MP Return to Section TOC Return to Section TOC Return to Section TOC Return to Section TOC Return to Master TOC Return to Master TOC Return to Master TOC Return to Master TOC OUTPUT RECTIFIER REMOV AL AND REPLACEMENT (continued) washers holding the rectifier bracket to the machine base.
CHOPPER BOARD ASSEMBL Y REMOV AL AND REPLACEMENT Service and repair should be performed by only Lincoln Electric factory trained personnel. Unauthorized repairs performed on this equipment may result in danger to the technician or machine operator and will invalidate your factory warranty .
TROUBLESHOOTING & REP AIR F-48 F-48 POWER MIG 350MP Return to Section TOC Return to Section TOC Return to Section TOC Return to Section TOC Return to Master TOC Return to Master TOC Return to Master TOC Return to Master TOC CHOPPER BOARD ASSEMBL Y REMOV AL AND REPLACEMENT (continued) FIGURE F .
TROUBLESHOOTING & REP AIR F-49 F-49 POWER MIG 350MP Return to Section TOC Return to Section TOC Return to Section TOC Return to Section TOC Return to Master TOC Return to Master TOC Return to Master TOC Return to Master TOC CHOPPER BOARD ASSEMBL Y REMOV AL AND REPLACEMENT (continued) REPLACEMENT PROCEDURE 1.
TROUBLESHOOTING & REP AIR F-50 F-50 POWER MIG 350MP Return to Section TOC Return to Section TOC Return to Section TOC Return to Section TOC Return to Master TOC Return to Master TOC Return to Mast.
REMOV AL PROCEDURE ELECTRIC SHOCK can kill . High voltage is present when input power is applied to the machine. Note: Cut cable ties as needed to improve access. PREP ARA TION 1. Disconnect main input power from the machine. 2. Remove the case side panels using a 3/8” nut dri- ver .
TROUBLESHOOTING & REP AIR F-52 F-52 POWER MIG 350MP Return to Section TOC Return to Section TOC Return to Section TOC Return to Section TOC Return to Master TOC Return to Master TOC Return to Master TOC Return to Master TOC MAIN TRANSFORMER AND OUTPUT CHOKE REMOV AL AND REPLACE- MENT (continued) LEAD DISCONNECTION 8.
TROUBLESHOOTING & REP AIR F-53 F-53 POWER MIG 350MP Return to Section TOC Return to Section TOC Return to Section TOC Return to Section TOC Return to Master TOC Return to Master TOC Return to Master TOC Return to Master TOC MAIN TRANSFORMER AND OUTPUT CHOKE REMOV AL AND REPLACE- MENT (continued) FIGURE F .
TROUBLESHOOTING & REP AIR F-54 F-54 POWER MIG 350MP Return to Section TOC Return to Section TOC Return to Section TOC Return to Section TOC Return to Master TOC Return to Master TOC Return to Mast.
TROUBLESHOOTING & REP AIR F-55 F-55 POWER MIG 350MP Return to Section TOC Return to Section TOC Return to Section TOC Return to Section TOC Return to Master TOC Return to Master TOC Return to Master TOC Return to Master TOC F AN MOTOR ASSEMBL Y REMOV AL AND REPLACEMENT (continued) FIGURE F .
VOL T AGE & CURRENT CALIBRA TION PROCEDURE Service and repair should be performed by only Lincoln Electric factory trained personnel. Unauthorized repairs performed on this equipment may result in danger to the technician or machine operator and will invalidate your factory warranty .
TROUBLESHOOTING & REP AIR F-57 F-57 POWER MIG 350MP Return to Section TOC Return to Section TOC Return to Section TOC Return to Section TOC Return to Master TOC Return to Master TOC Return to Mast.
TROUBLESHOOTING & REP AIR F-58 F-58 POWER MIG 350MP Return to Section TOC Return to Section TOC Return to Section TOC Return to Section TOC Return to Master TOC Return to Master TOC Return to Master TOC Return to Master TOC VOL T AGE & CURRENT CALIBRA TION PROCEDURE (continued) 9.
RETEST AFTER REP AIR Retest a machine: • If it is rejected under test for any reason that requires you to remove any part which could affect the machine’s electrical characteristics.
NOTES F-60 F-60 POWER MIG 350MP Return to Section TOC Return to Section TOC Return to Section TOC Return to Section TOC Return to Master TOC Return to Master TOC Return to Master TOC Return to Master .
G-1 ELECTRICAL DIAGRAMS G-1 T ABLE OF CONTENTS -ELECTRICAL DIAGRAMS SECTION- ELECTRICAL DIAGRAMS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SECTION G WIRING DIAGRAM (G4678) . . .
ELECTRICAL DIAGRAMS G-2 POWER MIG 350MP WIRING DIAGRAM - ENTIRE MACHINE EN -170 S O L ID E D G E G4678 P O W E R MI G 35 0 MP W I RI NG DI A G RA M NONE G4511 cstubl e J. SKE R B E C - UNLESS OTHERWISE SPEC IF I ED TOLERANCE MANUFACTURING TOL ERANCE PER E2056 ON 2 PLACE DEC IMALS IS ± .
Return to Section TOC Return to Section TOC Return to Section TOC Return to Section TOC Return to Master TOC Return to Master TOC Return to Master TOC Return to Master TOC ELECTRICAL DIAGRAMS G-3 POWER MIG 350MP SCHEMA TIC - ENTIRE MACHINE EN- 170 S O L I D E D G E G 4677 E NGINEERING CONTROLLED MANUFACTURE R: No CHANG E D ET AIL: REL EAS ED A.
ELECTRICAL DIAGRAMS G-4 POWER MIG 350MP SCHEMA TIC - CONTROL PC BOARD (G3789-1E2/1) G-4 NOTE: This diagram is for reference only . It may not be accurate for all machines covered by this manual.
ELECTRICAL DIAGRAMS G-5 POWER MIG 350MP SCHEMA TIC - CONTROL PC BOARD (G3789-1E2/2) G-5 NOTE: This diagram is for reference only . It may not be accurate for all machines covered by this manual.
ELECTRICAL DIAGRAMS G-6 POWER MIG 350MP SCHEMA TIC - CONTROL PC BOARD (G3789-1E2/3) G-6 NOTE: This diagram is for reference only . It may not be accurate for all machines covered by this manual.
ELECTRICAL DIAGRAMS G-7 POWER MIG 350MP SCHEMA TIC - CONTROL PC BOARD (G3789-1E2/4) G-7 NOTE: This diagram is for reference only . It may not be accurate for all machines covered by this manual.
NOTE: Lincoln Electric assumes no responsibility for liablilities resulting from board level troubleshooting. PC Board repairs will invalidate your factory warranty . Individual Printed Circuit Board Components are not available from Lincoln Electric.
ELECTRICAL DIAGRAMS G-9 POWER MIG 350MP SCHEMA TIC POWER SUPPL Y P .C. BOARD (G3631-3F0) G-9 NOTE: This diagram is for reference only . It may not be accurate for all machines covered by this manual.
NOTE: Lincoln Electric assumes no responsibility for liablilities resulting from board level troubleshooting. PC Board repairs will invalidate your factory warranty . Individual Printed Circuit Board Components are not available from Lincoln Electric.
ELECTRICAL DIAGRAMS G-11 POWER MIG 350MP SCHEMA TIC - CHOPPER P .C. BOARD (M20046-1M0) G-11 NOTE: This diagram is for reference only . It may not be accurate for all machines covered by this manual.
NOTE: Lincoln Electric assumes no responsibility for liablilities resulting from board level troubleshooting. PC Board repairs will invalidate your factory warranty . Individual Printed Circuit Board Components are not available from Lincoln Electric.
ELECTRICAL DIAGRAMS G-13 POWER MIG 350MP SCHEMA TIC - MSP3 PC BOARD (L1 1612-2D0) G-13 NOTE: This diagram is for reference only . It may not be accurate for all machines covered by this manual.
NOTE: Lincoln Electric assumes no responsibility for liablilities resulting from board level troubleshooting. PC Board repairs will invalidate your factory warranty . Individual Printed Circuit Board Components are not available from Lincoln Electric.
ELECTRICAL DIAGRAMS G-15 POWER MIG 350MP SCHEMA TIC - FEEDER P .C. BOARD (G3883-1E0/1) G-15 NOTE: This diagram is for reference only . It may not be accurate for all machines covered by this manual.
ELECTRICAL DIAGRAMS G-16 POWER MIG 350MP SCHEMA TIC - FEEDER P .C. BOARD (G3883-1E0/2) G-16 NOTE: This diagram is for reference only . It may not be accurate for all machines covered by this manual.
NOTE: Lincoln Electric assumes no responsibility for liablilities resulting from board level troubleshooting. PC Board repairs will invalidate your factory warranty . Individual Printed Circuit Board Components are not available from Lincoln Electric.
ELECTRICAL DIAGRAMS G-18 POWER MIG 350MP SCHEMA TIC - SPOOL GUN P .C. BOARD (L12008-2D0) G-18 NOTE: This diagram is for reference only . It may not be accurate for all machines covered by this manual.
NOTE: Lincoln Electric assumes no responsibility for liablilities resulting from board level troubleshooting. PC Board repairs will invalidate your factory warranty . Individual Printed Circuit Board Components are not available from Lincoln Electric.
ELECTRICAL DIAGRAMS G-20 POWER MIG 350MP SCHEMA TIC - DISPLA Y P .C. BOARD (L1 1756-1E1) G-20 NOTE: This diagram is for reference only . It may not be accurate for all machines covered by this manual.
NOTE: Lincoln Electric assumes no responsibility for liablilities resulting from board level troubleshooting. PC Board repairs will invalidate your factory warranty . Individual Printed Circuit Board Components are not available from Lincoln Electric.
SVM ERROR REPORTING FORM We need to know if there are errors in our manuals. W e also value any suggestions as to additional tests or procedures that would make this SVM a better tool for you.
デバイスLincoln Electric SVM165-Aの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Lincoln Electric SVM165-Aをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはLincoln Electric SVM165-Aの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Lincoln Electric SVM165-Aの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Lincoln Electric SVM165-Aで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Lincoln Electric SVM165-Aを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はLincoln Electric SVM165-Aの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Lincoln Electric SVM165-Aに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちLincoln Electric SVM165-Aデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。