Little WonderメーカーPRUNERの使用説明書/サービス説明書
ページ先へ移動 of 15
© 2006 Mantis, Div . of Schiller -Pfeiffer Inc. All Rights Reserved. Owner s Manual and Saf ety Instr uctions Pr uner “E” System.
1 T able of Contents Important Information A. Introduction This attachment is designed for trimming light to medium size branches. B. Pruner Attachment Specification. C. Contents of the package 1. Pruner Attachment Assembly with plastic gear case cover 2.
2 Safety and W arnings A. Safety Decals Please pay particular attention to the warning and information decals found on various parts of this Pruner Attachment unit. They are an important part of the safety system. These decals must be replaced in time due to abrasion, etc.
3 General Safety Rules 1. Remove branches in sections. Maintain safe operating positions, to avoid risk of being struck by falling branches or by those that rebound after hitting the ground 2. Cover saw chain with guard during transport and storage. 3.
4 Extension cord chart ( minimum cord gauge (A WG) ) 17. Stay alert . W atch what you are doing. Use common sense. Do not operate tool when you are tired, ill or under the influence of alcohol or other drugs.
5 1. Unscrew the mounting nut from the Gear Case Cover . Open the cover . (Picture 3) 2. Mount the Chain Guide. Be sure that threaded pin fits into the opening in the guide bar . (Picture 4) 3. Fit the saw chain into the groove in the Chain Guide bar , and around the sprocket.
6 1. Loosen mounting nut and adjust the chain tension by turning the tensioner screw 2. Hold unit vertically , and tighten mounting nut 3. Move saw chain backwards on guide bar by hand. Saw chain should move freely on guide bar if it is in proper mesh with the sprocket.
7 Check the balance of the assembled unit. The handles and shoulder harness have been assembled at the factory and set according to the average size person. This can be adjusted to the operator ’ s preference by simple loosening the screws and sliding handles up or down the shaft.
8 Service Maintenance Guide Area Maintenance procedure Frequency Spline male/female connection of the inner drive shaft Lubricate 20-25 Hrs Gear case Use a grease gun to insert lubricant into the grease nipple of the gear case. Use EP2 lithium grease 20-25 Hrs Guide bar Inspect/Clean/Replace The guide bar opening should be always a square.
9 Area Maintenance procedure Frequency Oiling port Inspect/Clean Before each use Nose sprocket Clean/Lubricate Before each use Saw chain Inspect/Clean/Sharpen/lubricate/Replace Before each use Screws/.
10 • A Low-kickback Chain • Low-vibration Chain • Narrow-kerf Chain FILING TOOLS FOR FILING Saw Chain Sharpening Procedur e Square-Gr ound Filing WHO SHOULD PERFORM SQUARE-GROUND FILING? Most chain saw users will probably never need to use square ground chain, nor learn to perform square ground filing.
11 GULLET FILING Approximately every 5th sharpening, clean out gullets with a 7/32" round file. File gullets from the inside out (the side opposite from sharpening). Leave a 1/8" shelf behind the gullet. The depth-gauge setting for all square-ground chisel chain is .
12 48 48 2 2 4 4 3 3 6 6 5 5 8 8 7 7 9 9 5 5 12 12 13 13 1 1 1 1 14 14 15 15 16 16 17 17 16 16 18 18 19 19 20 20 21 21 22 22 23 23 25 25 24 24 26 26 27 27 28 28 29 29 30 30 31 31 32 32 33 33 34 34 36 .
KEY # DESCRIPTION P ART # QTY 1 GEAR CASE COVER 3331 100 1 2 BEARING 6001-2Z 331 101 1 3 GEAR CASE 331 102 1 4 BEARING 627 331 103 1 5 BOL T M5X12 331500 5 6 GREASE FITTING 331104 1 7 SCREW , TENSIONE.
Specifications, descriptions, and illustrative material in this literature are as accurate as known at the time of publication, but are subject to change without notice.
デバイスLittle Wonder PRUNERの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Little Wonder PRUNERをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはLittle Wonder PRUNERの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Little Wonder PRUNERの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Little Wonder PRUNERで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Little Wonder PRUNERを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はLittle Wonder PRUNERの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Little Wonder PRUNERに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちLittle Wonder PRUNERデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。