LongshineメーカーLCS-IR2114-Cの使用説明書/サービス説明書
ページ先へ移動 of 36
Broadband Router User’s Manual JUNE 2009.
- 1 - FCC Warning This equipment has been tested and found to comp ly with the limits for a class B digital device, pursuant to Part 15 of the FCC Rules. These limita tions are designed to provide reasonable protection against harmful interferenc e in a residential installation.
- 2 - C o n t e n t s _ _ _ _ _ 1. Introduc tion ............................................................................................................... 4 1.1 Features ...........................................................................
- 3 - 3.8.2 Static Routing ................................................................................................ 32 3.8.3 Dynamic Routing ........................................................................................... 33 3.9 Misc .
- 4 - 1. Introduction ______ Congratulations on purch asing the Broadband Router. This Broadband Router, is a high quality and reliable Internet routing device, enables multiple us ers to share the Broadband Internet co nnection through a Cable or DSL modem.
- 5 - LAN Features ● 4-Port Ethernet Switch: The Broadba nd Router provides 4 10/10 0Base-T switchin g ports. ● Standard Compliance: The Broadba nd Router complies with the IEEE 802.3x full duplex flow control. ● DHCP Server Support: This feature provides a dynamic IP address to PCs and other d evices upon request.
- 6 - LED Light Status Description LED Light Status Description On (Steady Green) Broadband Router is powered on. PWR Off No power On (Steady Green) WAN port is successfully connected WAN Link/ACT Flashing Data is being sent or receiv ed.
- 7 - 2. PC Configuration _ _ _ _ User needs to configure TCP/IP network settings, Inte rnet acce ss configuration for ea ch system within the Broadband Router’s LAN netwo rk. By default, the Broad bnad Router acts as a DHCP server for server version of Windows, it automatically assigns IP address to each system when system s boot up.
- 8 - ‧ If you decide to use IP address from Wireless Router, sele ct “Obtain an IP address automatically” . ‧ If you decide to use the IP addr ess you are desired, select “Use the follo w ing IP address” . Make sure enter correct ad dresses in “IP Address” and “Subnet Mask” fields.
- 9 - b) Select “Internet Protocol (TCP/IP)” then cli ck “Properties” , window below will appear..
- 10 - ‧ If you decide to use IP address from Wireless Router, sele ct “Obtain an IP address automatically” . ‧ If you decide to use the IP addr ess you are desired, select “Use the follo w ing IP address” . Make sure enter correct ad dresses in “IP Address” and “Subnet Mask ” fields.
- 11 - ‧ If you decide to use IP address from Wireless Router, sele ct “Obtain an IP address automatically” . ‧ If you decide to use the IP addr ess you are desired, select “Use the follo w ing IP address” . Make sure enter correct ad dresses in “IP Address” and “Subnet Mask ” fields.
- 12 - 3. Setup Broadband Router Configurations via Web Browser The Broadband Router comes with a web-based configuration utilit y. Users can access this configuration utility from any of client system within Broadband Router ’s LAN. For best results, either use Microsoft Internet Explorer 6.
- 13 - 3.2 Quick Setup Quick Setup will help you setup the Broadband Router quickly. Th ere have six types of WAN Connections: Dynamic IP Address, Static IP, PPPoE, PPTP, L2TP, and BigPond. When configure the Quick Setup wizard, you ca n setup Host Settin gs, such a s Ho st name, Time Zon e, and Daylight Saving as below.
- 14 - 3.3 Administrator 3.3.1 Management Use this page to restrict management access ba sed on a specific password. Passwo rds can contain from 4-12 alphanumeri c characters, and are case sensitive. Idle Time-out - The amount of time of inactivity before t he Broadband Route r will aut omatically close the Administrator session.
- 15 - 3.3.2 System Settings The System Settings window configure s broadband router basic settings, such as router’ s Host Name, Set Time Zone, Daylight Saving and Operation Mode. NTP Server (IP or Domain Name): Enter a Domain Name if it was provid ed by the ISP Time Zone: Select the time zone of the country you are currently in.
- 16 - 3.3.4 Configuration Use this window to restore or backup b roadband router settings, su ch as Restore Factory Def ault, Backup Settings and Restore Settings. The Fa ctory Default settings are: “Username : admin ”, “Password : admin ”, “IP: 192.
- 17 - 3.3.5 Tools If for any reason the device is not responding correctly, you may want to restart the unit by clicking on the Reboot button. 3.3.6 Language Specify the language of the device menu. The tw o languages are supported i n this router: English and Traditional Chinese .
- 18 - 3.3.8 Logout Click Logout in the task bar to initiate broadband rout er logout process. 3.4 WAN Specify the WAN connection mode required by your Internet Service P rovider, then click " OK " Button to provide detailed configuration paramet er s for the selected connection type.
- 19 - DHCP: Obtain an IP address automatically from the ISP. MAC Address Clone: You can use the “ Clone MAC Addr ess ” button to copy the MAC address of the Ethernet Card installed by your ISP and replace the WAN MAC addres s with this MAC address.
- 20 - (c) PPPoE PPP over Ethernet is a common connection method used for xDSL. User Name and Password: Enter the User Name and Pa ssword you use when logging onto your IS P through a PPPoE or PPTP connection. Service Name: optional. Input the service name if your ISP requires it.
- 21 - PPTP: The Point-to-Point Tunneling Protocol (PPTP ) is a method for implementing virtual private network. Server: Specify IP Address of the PPTP Server. IP Address and Subnet Mask : the private IP address and su bnet mask your ISP assigned to you.
- 22 - L2TP Mode: The Layer two Tunneling Protocol (L2 TP) is a method for implementing virtual private network. Server: Specify IP Address of the L2TP Server. (f) BigPond BigPond is an Australian internet servi ce pr ovider and is a subsidiary of Telstra.
- 23 - Password: Enter the Password is provided by your ISP. This field is case -sensitive. Server IP: Enter the authenticating serv er IP address or host name. MTU: The normal MTU (Maximum Transmit Unit) value fo r most Ethernet networks is 1500 bytes.
- 24 - 3.5.2 DHCP Client List The DHCP client list allows you to see which clie nts are conn ected to the Broadban d Router via IP address, host name, and MAC addre ss. Y ou can select static to fix it. DHCP Client List: This page shows all DHCP clients (LAN P Cs) currently connected to your network.
- 25 - Enabled: Enable the Virtual Server option. Private IP: This is the LAN clie nt/host IP address that the Public Port number packet will be sent to.
- 26 - Enable: Enable the Port Triggering function. Trigger Port: This is the out going (Outbound) rang e of por t numbers for this particular application. Trigger Type: Select whether the outbo und port protocol is “ TCP ”, “ UDP ” or “ Both ”.
- 27 - Enabled: Enable the Port Mapping function. Comment: The description of this setting. Server IP: Enter the NAT server IP address. Mapping Ports: Enter the port address NAT se rver maps to. Typ e: Select the Inbound port protocol type: “ TCP ”, “ UDP ” or “ Both ”.
- 28 - [VPN] PPTP Passthrough: PPTP is a protocol that allows corporat ions to extend their own corporate net work through private “tunnels” over the publi c Interne t.
- 29 - Enable: Enable/disable DMZ. (Default: Disable) Public IP Address: The IP address of the WAN port or any other Public IP addr esses given to you by your ISP.
- 30 - 3.7.2 Client Filtering You can filter Internet access for local cli ents based on IP addresses, application types, (i.e., HTTP port), and time of day. For example, this screen shows th at clients in the address range 192.16 8.2.50-99 are permanently restricted from using FTP (Port 21), whil e clients in t he address range 192.
- 31 - 3.7.3 URL Filtering URL Filtering feature allowing you to prevent users from accessing specified websites on the basic of some policy. Default is “ Disable URL Filter Function ”. 3.7.4 MAC Filtering The MAC address filer let user to allow or block certain client PCs accessing the Internet ba sed on MAC address.
- 32 - 3.8 Routing 3.8.1 Routing Table The routing table displays the curr ent routing inform ation in system. 3.8.2 Static Routing A static route is a pre-determined pathw ay that netwo rk information must tr avel to reach a specific host or network.
- 33 - 3.8.3 Dynamic Routing Dynamic Routing can be u sed to cache routers learn ed by routing protocols, thus allowing the automation of static routing maintenance.
- 34 - 3.9.2 DDNS DDNS (Dynamic DNS) p rovides you on the Internet with a metho d to tie their domain name to a compute r or server. DDNS allows your domain name to follo w your IP address autom atic ally by having your DNS records changed when your IP addre ss changes.
- 35 - 3.10.2 Log The log file keeps a runnin g log of events and activities o ccurring on the device. You may wan t to save the log files by clicking on Log Setting.
デバイスLongshine LCS-IR2114-Cの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Longshine LCS-IR2114-Cをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはLongshine LCS-IR2114-Cの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Longshine LCS-IR2114-Cの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Longshine LCS-IR2114-Cで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Longshine LCS-IR2114-Cを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はLongshine LCS-IR2114-Cの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Longshine LCS-IR2114-Cに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちLongshine LCS-IR2114-Cデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
