Lowrance electronicメーカーEP-90Rの使用説明書/サービス説明書
ページ先へ移動 of 32
1 Pub. 988-0154-641 EP-90R Pressure Electronic Sensor Installation and Configuration Instructions This document shows how to insta ll an EP-90R Pressure sensor and how to connect it to a NMEA 2000 ® network.
2 The EP-90R consists of a red cabl e connector and the EP-90R housing with standard size ho se barb attachment. The EP-90R Water Pressure sensor, like the other L owranceNet Electronic Probe (EP) sensors, is designed for use with a NMEA 2000 DeviceNet Network.
3 For complete instructions on se tting up a new NMEA 2000 network or expanding an existing one, see the other document packed with your EP-90R, " Setup and Installation of NMEA 2000 Networks, General Information " part number 988-0154-173. If that document is not available, it can be downloaded free from the Lowrance web site.
4 3. Slide the pressure hose onto th e EP-90R hose barb attachment. If it does not fit snugly, secure it with a zip tie at the base of the hose barb attachment. 4. Now you are ready to remove the speedometer. Refer to the speedometer’s installation manual for removal instructions.
5 In similar fashion, a NMEA 2000 network allows multiple display units to receive data from a GPS antenna or multiple sonar units to receive messages sent from a temperature sensor.
6 NMEA 2000 network node located at the end of a NMEA 2000 backbone. NOTE: If you have a double T Connector on your network that is not attached to a device, you must cap the unused connector with a NMEA 2000 cap. This will protect the pin connectors from corrosion.
7 In this example, a new device is added to the N ME A 2000 bus by installing a T conn ector between a T connector and a terminator at the end of the backbone (network bus).
8 Notes.
9 LMF-200: EP-90R Pressure Configuration This section covers how to use EP- 90R Pressure Sensor with the LMF- 200 Multi-function gauge. NOTE: You will notice the LMF-200 does not have an Exit key. Menus will time out after a preset amount of time (3, 5, 10 or 15 seconds).
10 4. Use the UP and DOWN keys to input the number of gallons the tank will hold and press MENU . Repeat steps 3 and 4 for each additional tank. After all tanks have been set up, you will be directed to the m ain display.
11 To unconfigure the EP-90R: 1. Press MENU , select S YSTEM S ETUP and press MENU . 2. Highlight B US D EVICES and press MENU . Select a configured pressure sensor and press MENU . 3. The pressure sensor menu will appear. Highlight U NCONFIG and press MENU .
12 A dding a page: 1. Press MENU , use the UP and DOWN keys to select P AGE S and press MENU , which will open the Pages menu with the following options: Add Page, Rem Page, Autos croll and Set Pop-up. 2. Highlight A DD P AGE and press MENU . 3. Select Gauge, Single Digital or Dual Digital and press MENU .
13 up to three options. (If your unit is configured for one engine, or if you chose Pitot Speed or Atmospheric Pressure, you will be directed back to the main display.) 4. Select the desired engine and press MENU . You will be taken back to the main display.
14 3. Select the desired option and press MENU . The Pressure Range menu will appear with the following option s: 0-30 psi, 0-60 psi, 0-80 psi and 0-100 psi.
15 LMF-400: EP-90R Pressure Configuration This section covers how to use your E P - 9 0 R P r e s s u r e S e n s o r w i t h t h e LMF-400 Multi-function gauge.
16 5. After all tanks on your vesse l have been set up, press EXIT repeatedly to return to the main display. Boat Setup Reset If you want to access the Setup scr een (Boat Setup) after an engine- tank configuration has been chosen you will have to reset the configuration to default settings.
17 4. Press ENTER . You will be taken back to the Bus Devices list. Press EXIT repeatedly to return to the main display. To reconfigure the EP-90R: 1. Press MENU , select S YSTEM S ETUP and press ENTER . 2. Highlight B US D EVICES and press ENTER . Select a configured pressure sensor and press ENTER .
18 Customizing Pages The customizing pages feature allows you to choose what data will be displayed on selected pages. You can use the Single Analog, Dual Analog, Quad Analog, Single Digital, Dual Digital, Quad Digital pages and Fuel Manager pages to di splay pressure sensor data.
19 To customize Quad A nalog pa ge: 1. Make sure the Quad Analog page has been added to the page screen rotation. 2. Use the ENTER and EXIT keys to scroll the Quad Analog page onto the main display.
20 5. Highlight P ITOT S PEED , E NG B ST P RESS , E NG O IL P RESS , E NG W TR P RESS , F UEL P RESSURE , T RNS O IL P RESS or A TM P RESSURE and press ENTER .
21 Pressure Range (Analog Pages only) From the Single, Dual and Quad Analog pages, you can set pressure ranges for Boost, Oil, Fuel and Transmission Oil Pressure. To set pressure range: 1. From an analog page, press MENU , select S YSTEM S ETUP and press ENTER .
22 To reset pressure sensor values: 1. Press MENU , select S YSTEM S ETUP and press ENTER . 2. Highlight B US D EVICES and press ENTER . 3. Select the desired pr essure sensor and press ENTER . 4. Highlight R ESET V ALU ES and press ENTER . The following message will appear: Press Enter to Reset Values .
23 Display Unit: EP-90R Pressure Configuration This section will show you how to us e an EP-90R Pressure Sensor with a display unit. The LMS-525cDF is one of many Lowrance display units that may be used with the EP-90R Pressure Sensor.
24 Engine & Tank Configuration The Engine-Tank configuration me nu is located below the NMEA 2000 Devices list, but will only be accessibl e if engine- or fuel-related devices are on the network. When choosing an engine-tank configuration you will use the Tank Select menu, Tank Size dialog box and Set Configuration button.
25 9. When all tanks have been configured, highlight the S ET C ONFIGURATION button and press ENTER . The following confirmation message will appear: Are you sure you wish to change the bus configuration? Choose Y ES and press ENTER , Press EXIT to return to the main display.
26 4. Use the UP and DOWN keys to change the Device Name. When you have finished inputting the desired Device Name, press ENTER . Press EXIT repeatedly to return to the main display. To reset device name to default setting: 1. Press MENU twice, select NMEA 2000 or N ETWORKING and press ENTER .
27 To select Pressure Type : 1. Press MENU twice, select NMEA 2000 or N ETWORKING and press ENTER . A menu will appear with five options: Bus Setup, Fuel Management, NMEA 2000 Alarms, Waypoint Sharing and Backlight Synchronization. 2. Highlight B US S ETUP and press ENTER , which will open the Bus Configuration menu.
28 6. Highlight Y ES and press ENTER . Press EXIT repeatedly to return to the main display. NMEA 2000 Alarms When you set a NMEA 2000 Alarm for a pressure sensor, a pop-up window will appear and an alarm will sound when pressure exceeds or falls below a preset PSI level of your choosing.
29 Notes.
30 Notes.
31 LOWRANCE ELECTRONICS FULL ONE-YEAR WARRANTY "We," "our," or "us" refers to LOWRAN CE ELECTRONICS, INC., the manufacturer of this product. "You" or "your" refers to the first person wh o purchases this p roduct as a consumer item for personal, family or household use.
32 How to Obtain Service… …in the USA: Contact the Factory Customer Se rvice Department. Call toll-free: For Lowrance: 800-324-1356. For Eagle: 800-324-1354 8 a.
デバイスLowrance electronic EP-90Rの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Lowrance electronic EP-90Rをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはLowrance electronic EP-90Rの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Lowrance electronic EP-90Rの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Lowrance electronic EP-90Rで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Lowrance electronic EP-90Rを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はLowrance electronic EP-90Rの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Lowrance electronic EP-90Rに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちLowrance electronic EP-90Rデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
