Lowrance electronicメーカーLCX-104Cの使用説明書/サービス説明書
ページ先へ移動 of 200
Pub. 988-0151-031 www.lowrance.com LCX-104C Fish-finding Sonar & Mapping GPS Operation Instructions.
Copyright © 2002 Lowrance Electron ics, Inc. All rights reserved. Lowrance ® is a registered trademark of Lowrance Electronics, Inc. MapCreate is a trad emark of Lowrance Electronics, Inc. Marine-Tex is a trademark of Illinois Tool Works Inc.
i Table of Contents Sec. 1: Read Me First! .............................................................. 1 Capabilities and Specifications: LCX-104C .................................. 3 How your Sona r Works ..........................................
ii Sonar Oper ations ........................................................................ 48 Fish Symbols vs. Fu ll Sonar Ch art ........................................ 50 Other Free Trai ning Ai ds ...............................................
iii Upper and Lowe r Limits ............................................................ 84 Zoom & Zoom Bar ....................................................................... 84 Zoom Pan .......................................................
iv Routes ........................................................................................ 125 Create and Save a Rout e ...................................................... 126 Delete a Ro ute ................................................
v Fill Water with White ........................................................... 146 Map Overlays (Range Ring s; Lat/Long Grid) ...................... 146 Map Datum Sele ction ............................................................... 146 Map Detail Category Selection.
vi WARNING! A CAREFUL NAVIGATOR NEVER RELIES ON ONLY ONE METHOD TO OBTAIN POSITION INFORMATION. CAUTION When showing navigation data to a position (waypoint), a GPS unit will show the shortest, most direct path to the waypoint. It provides navigation data to the waypoint regardless of obstructions.
1 Section 1: Read Me First! How this manual can get you out on the road, fast! Welcome to the exciting world of digital sonar and GPS! We know you're anxious to begin navigating and finding fish, but we have a favor to ask.
2 After you've gained some experience with your sonar, you'll want to check out Section 4, which discusses more advanced Sonar Options and Other Features .
3 how many watts of power the unit ha s, or how many waypoints it can store, skip ahead to important info rmation on how sonar works, on page 5. (Background on GPS begins on page 6.) Capabilities and Specifications: LCX-104C General Display: .........
4 Sonar sounding depth capability: ........... 3,000 feet (915 meters). Actual capability depends on transducer configuration and in- stallation, bottom composition and water conditions. All sonar units typically read deeper in fresh water than in salt water.
5 Position updates: .......... Every second. Position points: ............. 1,000 waypoints; 1,000 event marker icons. Man Overboard: ............. MOB feature precisel y marks man overboard location with special icon, then automatically displays navigation data to that position.
6 (fish, structure, bottom) and bounc es back to the transducer, which converts the sound back into an electrical signal. The receiver amplifies this return si gnal, or echo, and sends it to the display, where an image of the ob ject appears on the scrolling sonar chart.
7 The performance doesn't stop there. Stored in the permanent memory of every unit is a basic background map of the entire world. We lock it in here at the factory — you can't change or erase this map.
8 MMC, custom map files and GPS data files can be used interchangea- bly between your gimbal-mounted LCX-104C and the hand-held iFINDER GPS receiver.) The unit automatically reads Custom Map Files directly from the MMC or SDC. To use a custom map, all yo u n e e d t o d o i s s l i d e a n M M C c o n - taining a map into the unit.
9 A minimum of three satellites are required to determine a 2D fix. Remember, the unit must have a clear view of the satellites in order to receive their signals. Unlike radio or television signals, GPS works at very high frequencies. These signals can be easily blocked by trees, buildings, an automobile roof, even your body.
10 First, the U.S. government has not completed construction of the WAAS system, so it is not yet fully operational. The ground stations are in place, but only a few of the needed WAAS satellites have been launched. WAAS can boost the accuracy of land GP S navigation, but the system is designed for aircraft.
11 Menu Commands A menu command or a menu option will appear in small capital letters, in a bold sans serif type like this: R OUTE P LANNING . These indicate that you are to select this command or option fr om a menu or take an action of some kind with the menu item.
12 Notes.
13 Section 2: Installation & Accessories Preparations You can install the sonar and GPS sy stems in some other order if you prefer, but we recommend this installation sequence: CAUTION: You should read over this entire installation section before drill- ing any holes in your vehicle or vessel! 1.
14 Read these instructions carefully before attempting the installation. Determine which of the mounting posi tions is right for your boat. Use extreme care if mounting the transducer inside the hull, because once it is epoxied into position, the transducer usually cannot be removed.
15 2. The transducer should be insta lled with its face pointing straight down, if possible. 3. If the transducer is mounted on th e transom, make sure it doesn't inter- fere with the trailer or hauling of the boat. Also, don't mount it closer than approximately one foot from th e engine's lower unit.
16 However, there are times when you may need to adjust the transducer slightly higher or lower. (The slot s in the mounting brackets allow you to loosen the screws and slide the tr ansducer up or down.
17 bracket with the letter "A" aligned wi th the dot stamped into the metal bracket. This position sets the transducer's coarse angle adjustment for a 14 ° transom. Most outboard and stern-drive transoms have a 14 ° angle. Align plastic ratchets in bracket.
18 Add ratchets to bracket and transducer. 2. Aligning the transducer on the transom. A. One-piece bracket: Slide the transducer between the two ratch- ets.
19 B. Two-piece bracket: Assemble the transducer and bracket as shown in the following figure. Temporarily slide the bolt though the transducer assembly but don't tighten the nut at this time. Hold the assembled transducer and bracket against the transom.
20 B. Two-piece bracket: Once you determine the correct position for the ratchets, assemble the transduc er as shown in the figure in step 2B. Don't tighten the lock nut at this time. 4. Drilling mounting holes. Hold the transducer and bracket a ssembly against the transom.
21 Both bracket types: Attach the transducer to the transom. Slide the transducer up or down until it's aligned properly with the bottom of the hull as shown in the preceding and following figures. Tighten the bracket's mounting screws, sealing them with the caulking compound.
22 7. Make a test run to determine the results. If the bottom is lost at high speed, or if noise appears on the display, try sliding the trans- ducer bracket down. This puts the transducer deeper into the water, hopefully below the turbulence ca using the noise.
23 TRANSDUCER ORIENTATION AND FISH ARCHES If you do not get good fish arches on your display, it could be because the transducer is not parallel with th e ground when the boat is at rest in the water or at slow trolling speeds. Transducer angles and their effects on fish arches.
24 transducer installation can be made on hulls with flotation materials (such as plywood, balsa wood or fo am) between layers of fiberglass if the material is removed from the chosen area.
25 cation that shot through the hull th e best and follow the instructions on the following pages for a shoot-thru-hull mounting. Shoot-thru-hull transducer locations for high speed or trolling speed operation.
26 Place the transducer into the epoxy, twisting and turning it to force any air bubbles out from under the transducer face. The face of the transducer should be parallel with the hull, with a minimum amount of epoxy between the hull and tr ansducer. After the epoxy dries, route the cable to the sonar unit.
27 Sensor Chart Two-temperature sensor installation Three-temperature sensor installation with speed Three-temperature sensor installation TS-3X temperature sensor SP-X speed sensor MY-4X Cable TS-2X .
28 Optional Speed Sensor Installation This unit can display speed and dist ance traveled; the feature requires a speed sensor which may or may not come packaged with your unit. (If you wish to purchase an optional addi tional sensor for your unit, refer to the accessory ordering informat ion inside the back cover of this manual.
29 Speed sensor mounting configuration: side view (left) and rear view (right.) If the base of the transom has a ra dius, fill the gap between the tran- som and the sensor with the caulki ng compound. This will help ensure a smooth water flow. Route the sensor's cable through or over the transom to the sonar unit.
30 You need to select an antenna insta llation location that has a clear, un- obstructed view of the sky. After the module is installed, route the cable to the unit, plug it in the center socket on the back and your system is ready to use.
31 CAUTION: Do not use this product without a 6-amp fuse wired into the power cable! Failure to use a 6-amp fuse will void your warranty. This unit has reverse polarity protection. No damage will occur if the power wires are reversed. However, the unit will not work until the wires are attached correctly.
32 Communication Port Wiring Diagrams Com-1 wiring to receive DGPS position information from a DGPS receiver. Com-1 wiring to receive NMEA position information from some other GPS receiver. Com-1 wiring to transmit NMEA position information to another NMEA-compatible device.
33 Cable connections. Note: External speaker wires in power/data cable not shown. Mounting the Unit: Bracket or In-Dash You can install the unit on the top of a dash with the supplied gimbal bracket. It can also be installed in the dash. For an in-dash mount, con- sult the factory customer service department.
34 Front view (left) and side view (right) showing dimensions of the so- nar/GPS unit when mounted on gimbal bracket. Install the gimbal bracket. Orient the bracket so the arms slope toward the front of your unit. Front Screw mounting hole Cable hole Inch [Millimeter] 12.
35 Once a location is determined, use the bracket as a template and mark the mounting holes and the hole for the cables. Drill a 1-inch (25.4 mm) hole in the dash for the power, transducer and antenna cables. Screw the bracket to the mounting surface.
36 Memory card compartment with a 16 MB MMC card installed. To remove an MMC 1. Open the card compartment d oor by unscrewing the thumb screw. The screw should only be finger tigh t. If it was over-tightened, use a thumbnail, a coin or a screwdriver to open the door.
37 its anti-glare properties, always use the special cleaner available from your dealer or LEI Extras. To remove fingerprints, water spot s, dust or other grime from the screen, hold the bottle about 6 inch es (15 cm) from the screen and spray. Wipe immediately with a clean, dry, lint-free cloth.
38 You can purchase an external speaker at your nearest audio electronics store. The unit is designed to work with most speakers, but make sure to buy one that meets these minimum requirements: • Minimum 8-ohm resistance • Minimum 5-watt power In your vessel or vehicle, mount th e speaker wherever you want to hear your unit's sounds.
39 Section 3: Basic Sonar Operation This section addresses the unit's most basic sonar operations. The in- structions presented in Sec. 3 follo w a chronological order. Sec. 4, Sonar Options & Other Features , will discuss other more advanced functions and utilities.
40 3. MENU – Press this key to show the menus and submenus, which allow you to select a command or ad just a feature. This also accesses search functions for streets, inters ections, addresses and highway exits.
41 about the various sonar options, see Sec. 4, Sonar Options & Other Fea- tures. (For general system setup and GPS options, see Sec. 8, System Setup and GPS Setup Options .) You can access the Main Menu from any of the four Page screens by pressing MENU | MENU .
42 System Setup command: sets general configuration options. Sun/Moon Calculations command: finds the rising and setting time of the sun and the moon. Trip Calculator command: shows trip status and statistics. Timers command: controls the up timer, down timer and alarm clock settings.
43 WARNING: Do not begin navigating with this unit until the numbers have stopped flashing! Satellite Status Page showing satellite lock-on with a 3D position acquired (latitude, longitude and altitude), including WAAS reception.
44 always at the top of the screen. The arrow in the center of the screen is your present position. It points in the direction you're traveling. Map Page, showing position on Bull Shoals Lake, Arkansas. At left is the full map option. At right, map with sonar option.
45 At left, Pages Menu, showing sonar chart display option commands. At right, Sonar Page in full sonar chart display mode. Sonar chart display options (from left) split zoom and split frequency. Sonar chart display options (from left) digital data and FlashGraf .
46 Sonar Page Menu. Most of these functions are discussed in Sec. 4. Sonar Page, showing full sonar chart mode. You can customize how the Sonar Page displays its pictures and other data in many ways. Your unit also includes several special sonar features and options that can help you bette r interpret the underwater scene.
47 LCX-104C Sonar Quick Reference 1. Mount the transducer, antenna an d unit. Connect the unit to electric power and the transducer. (If GPS op eration is desired, connect GPS antenna, too.) Make sure the MMC is in. (See complete installation de- tails beginning on page 13.
48 Sonar Operations As you can see from the quick reference on the previous page, basic operation is pretty easy, right out of the box. If you are a sonar novice, try operating the unit with the factory defaults until you get a feel for how it's working.
49 Adjusting sensitivity in Auto Sensitiv ity Mode is similar to manually ad- justing a car's speed with the accelera tor pedal while cruise control is on. You can tell the car to run faster, bu t when you let off the gas the cruise control automatically keeps you from running slower than the minimum speed setting.
50 Important Tip: While you are experimenting and learning, it's possible to scramble the settings so that the sonar picture disappears from your screen. If that happens, remember that it 's easy to switch back to full automatic operation by simply restoring the factory auto settings.
51 Sonar Tutorial, which includes an imated illustrations and more pic- tures of actual sonar returns, all described in detail. There's even a "printer friendly" version of the tutorial available on our web site…it makes a great supplement to this operation manual! You can also download a free copy of our Sonar Viewer software.
52 Free training emulator is available for your unit on our web site. The emulator works exactly like your real sonar/GPS unit. Using the Sonar Simulator and GPS Simulator features, it allows you to p.
53 Section 4: Sonar Options & Other Features Material in this section is a rranged in alphabetical order. ASP (Advanced Signal Processing) The ASP feature is a noise rejection sy stem built into the sonar unit that constantly evaluates the effects of boat speed, water conditions and interference.
54 Alarms This unit has three different types of sonar alarms. The first is the Fish Alarm. It sounds when the Fish I.D. feature determines that an echo is a fish. Another alarm is the Zone Alarm, whic h consists of a bar on the side of the screen.
55 4. Press ← to S HALLOW A LARM E NABLED | ENT | EXIT | EXIT | EXIT . 5. To turn off the alarm, press MENU | MENU | ↓ to A LARMS | ENT | ↓ to S ONAR A LARMS | ENT | ENT | EXIT | EXIT | EXIT . To switch to a different depth setti ng, open the Sonar Alarms menu and repeat the instructions in step 3 above.
56 4. To set the lower boundary for the Zone Alarm, use ← or → to select L OWER , then press ↑ or ↓ to move the bottom of the bar to the desired depth. 5. Press EXIT | ← to Z ONE A LARM E NABLED | ENT | EXIT | EXIT | EXIT . Now, any echo — fish, bottom, structure — wi thin the zone alarm's depth range will trigger the zone alarm.
57 For example, if you figure the sensor is reading 10 percent faster than actual speed, you will enter – 10 in the calibration window. If the sen- sor is reading 5 percent slower th an true speed, you will enter + 5 in the window.
58 If you do experiment with chart sp eed, remember to reset it to maxi- mum when you resume trolling or mo ving across the water at higher speed. To change chart speed: 1. From the Sonar Page, press MENU | ↓ to C HART S PEED | ENT . 2. The Chart Speed Control Bar appears.
59 This series of figures shows how different ColorLine settings can reveal more information. The "A" figures to the left show locations with Color- Line set at the factory level of 70 percent. At right, the "B" figures show the same locations with ColorLine increased to 84 percent.
60 Depth Cursor The depth cursor consists of a horizo ntal line with a digital depth box on the right side. The numbers inside the box show the depth of the cursor. At left, Sonar Page menu with Depth Cursor command selected. At right, sonar chart with the depth cursor active.
61 At left, Sonar Page menu with Depth Range command selected. At right, the Depth Range Control Scale. 2. The Depth Range Control Scale appears. Press ↑ or ↓ to select a dif- ferent depth range. A black bar hi ghlights the selected range. Range numbers in gray cannot be selected.
62 Changing the upper and lower limits gives you far greater control over the depth range. This feature lets you "zoom in" the display in almost unlimited combinations. Nearly any segment of the water column, from the surface to the bottom can be show n.
63 To turn off upper and lower limits: From the Sonar Page, press MENU | ↓ to A UTO D EPTH R ANGE | ENT | EXIT . FasTrack This feature automatically converts all echoes to short horizontal lines on the display's far right side. The gr aph on the rest of the screen con- tinues to operate normally.
64 Does that mean Fish I.D. is broken ? No — the feature is simply inter- preting sonar returns in a specific wa y to help take some of the work out of reading the screen. Remember: Fi sh I.D. is one of the many tools we provide so you can analyze yo ur sonar returns for maximum fish finding information.
65 To turn the Fish I.D. feature on: 1. From the Sonar Page, press MENU | ↓ to S ONAR F EATURES | ENT . 2. Press → ↓ or → to F ISH ID S YMBOLS | ENT | EXIT | EXIT . To turn off Fish I.D., repeat the instructions in step 1. FishTrack The FishTrack feature shows the dept h of a fish symbol when it ap- pears on the display.
66 The 200 kHz transducer will give yo u better detail and definition, but less depth penetration. The 50 kHz transducer will give you greater depth penetration, but a little less detail and less definition. (Remember, all sonar units typically read deeper in fresh water than in salt water.
67 nar Simulator.) If you have a pers onal computer and Internet access, visit our web site, www.lowrance.c om, and download the free Sonar Viewer and the emulator for your unit. These programs will allow you to replay sonar logs on your personal computer.
68 Overlay Data command on the Sonar Menu, at left. Overlay Data Shown selection menu, right. In this example, we scrolled down the data list to highlight "Ground Speed." When selected, the data type shifts to the top of the data list and a check mark appears beside the data type.
69 2. Press ↓ or ↑ to select Data Type |press → or ← to Data Size | EXIT . The selected data type will be displa yed in the new size. (To change the font size for another Data Type, press ENT and repeat these steps, be- ginning with step two above.
70 However, when you are running at high speeds, or just want the fastest possible screen update, you may want to use the HyperScroll feature. When you change the Ping Speed to any setting greater than 50 per- cent, the unit automatically enters HyperScroll mode.
71 When you boost ping speed and swit ch into HyperScroll, the width of the FasTrack bar graph display doubles in width at the right side of the screen. The allows you to better s ee the virtually instantaneous sonar returns, just as you would on a fla sher sonar unit.
72 Set Keel Offset This unit measures water depth from the face of the transducer. Since the transducer is installed below th e water surface, the distance dis- played by the digital depth, chart depth scale, chart cursor or fish sym- bols is not the exact water depth.
73 3. Press → to the first number, then press ↑ to change the number to 1. 4. Press → to the second number, them press ↑ to change the num- ber to 5, then press EXIT . The depth indicators now accurately show the water depth from surface to bottom.
74 At left, Sonar Menu with Sensitivity command selected. At right, the Sensitivity Control Bar. To adjust sensitivity in manual mode: 1. First, turn off Auto Sensitiv ity: from the Sonar Page, press MENU | ↓ to A UTO S ENSITIVITY | ENT . 2. Press ↑ to S ENSITIVITY | ENT and the Sensitivity Control Bar appears.
75 3. Press ↓ or ↑ to Mode Name | ENT . 4. Press EXIT | EXIT to return to the Sonar Page. Sonar Page & Sonar Chart Display Options The Pages Menu offers five chart disp lay options for units with dual- frequency transducers and four options for units with single-frequency transducers.
76 Full Sonar Chart. The Overlay Data (depth and water temperature) are each set to a different text size. Split Zoom Sonar Chart A split chart shows the underwater wo rld from the surface to the bot- tom on the right side of the screen. The left side shows an enlarged ver- sion of the right side.
77 Split Frequency Sonar Chart page, with 50 kHz view at left and 200 kHz view at right. You can adjust the sensitivity in each window. To adjust sensitivity in auto mode: 1. Press MENU | ENT . 2. The unit asks which you wish to adjust. Press ← or → to select the one you want | ENT .
78 Digital Data/Chart This mode shows the chart on the right side of the screen. The left side has seven large digital boxes or window s containing: Water Depth; Water Speed (from an optional speed se.
79 2. The Water Speed window title bar flashes, indicating the window contents can be changed. Press ENT | ↑ or ↓ to select data type | ENT | EXIT . Options List for customizing Digital Data windows. At left, the list first appears with Water Speed selected.
80 FlashGraf page. Map With Sonar Split Screen There is a page mode that splits the screen in half, with the map on the left and the sonar on the right. This screen option can be found on the Pages Menu under the Map Page category. Map With Sonar split screen option.
81 At left, Main Menu with Sonar Setup command selected. Center, sub-menu with Sonar Simulator comma nd selected. At right, Sonar Simulator menu, with simulator turned on (check box is checked). NOTE: With Simulate Position checked, the simulator will also automati- cally run the GPS simulator (if GPS data was recorded with the so- nar log).
82 1. Press MENU | MENU | ↓ to S ONAR S ETUP | ENT | ↓ to S ONAR S IMULATOR | ENT . 2. Press ↓ to C HART U SED | ENT . 3. Press ↓ or ↑ to select chart name | ENT | ↑ to S ONAR S IMULATOR O N | ENT | EXIT .
83 Stop Chart If you are running multiple units on a boat or using this unit in a car, there are times when you may want to turn off the sonar. This com- mand turns off the sonar and stops the chart from scrolling. Sonar re- starts automatically each time you turn on your unit.
84 Sonar Features menu with Surface Clarity selected. 2. Press → to S URFACE C LARITY | ENT. 3. Press ↓ or ↑ to select clarity level | EXIT | EXIT | EXIT . In the illustration at left, Surface Clarity is turned off. The right view shows Surface Clarity set at High.
85 For example, pressing the ZIN key once will enable a 2X zoom which will show all echoes that are be tween the top and bottom of the 2X zoom bar. Pressing the key again will give a 4X zoom and only the ech- oes between the top and bottom of the 4X bar will show on the screen.
86 Notes.
87 Section 5: Sonar Troubleshooting If your unit is not working, or if yo u need technical help, please use the following troubleshooting section befo re contacting the factory customer service department. It may save you the trouble of returning your unit for repair.
88 This causes the sonar to automati cally increase its Discrimination or noise rejection feature. This can cause the unit to eliminate weaker signals such as fish or even structure from the display. 3. The water may be deeper than the sonar's ability to find the bottom.
89 NOISE A major cause of sonar problems is electrical noise. This usually appears on the sonar's display as ra ndom patterns of dots or lines. In severe cases, it can completely cover the screen with black dots, or cause the unit to operate erratically, or not at all.
90 Notes.
91 Section 6: Basic GPS Operations This section addresses the unit's most basic GPS operations. The tuto- rials presented in Sec. 6 follow a chronological order. Sec. 7, Advanced GPS Operations , will discuss other more advanced functions and utili- ties.
92 3. MENU – Press this key to show the menus and submenus, which allow you to select a command or ad just a feature. This also accesses search functions for streets, inters ections, addresses and highway exits.
93 box with the factory default settings. But, if you want to learn about the various options, see Sec. 8, System Setup and GPS Setup Options . You can access the Main Menu from any of the four Page screens by pressing MENU | MENU . To clear the menu screen and return to the page display, press EXIT .
94 of the sun and the moon. Trip Calculator command: shows trip status and statistics. Timers command: controls the up timer, down timer and alarm clock settings. Browse MMC Files command: this allows you to view the installed MMC card and the files it contains.
95 No matter what Page you are on, a flashing current position indica- tor/question mark symbol and flashing GPS data displays indicate that satellite lock has been lost and there is no position confirmed. The Sat- ellite Status Page shows you the qu ality and accuracy of the current satellite lock-on and position calculation.
96 rently has. The smaller the position error number, the better (and more accurate) the fix is. If the position error flashes dashes, then the unit hasn't locked onto the satellites , and the number shown isn't valid. The Satellite Status Page has its ow n menu, which is used for setting various options.
97 NOTE: Remember, when the Speed, Track and Position information dis- plays are flashing, satellite lock ha s not been achieved and no posi- tion fix has been determined. A ques tion mark will also flash on the present position arrow in the center of the compass rose.
98 Navigation Page, backtracking a trail while creating a new trail. In the example figure above, the driver is headed north (a 355º track) toward a waypoint 355º (bearing) away. The cross track error range (white corridor) is 0.20 miles either side of the course.
99 The map zoom range is the distan ce across the screen. This number shows in the lower right corner of the screen. In the first example fig- ure below, the range is 4,000 miles fr om the left edge of the map to the right edge of the map.
100 The medium-detail U.S. maps contain: all incorporated cities; shaded metropolitan areas; county boundarie s; shaded public lands (such as national forests and parks); some major city streets; Interstate, U.
101 can reduce screen clutter and ma ke streets and other map features easier to see by simply turning off the display o f P O I s y o u ' r e n o t watching for. (To see how, check the text on Map Detail Category Selection, page 147. It shows how to use the Map Categories Drawn menu to turn individual POI displays off and on.
102 operate on. A dark blue title bar denotes the active window. Resize Window is another extremel y handy feature for pages that have two major windows. You can change th e horizontal size of the windows to suit your viewing preference. Here's how: 1.
103 GPS Quick Reference Start outdoors, with a clear view of the open sky. As you practice, try navigating to a location at least a few blocks away. While you're learning, navigation in too small an area w ill constantly trigger arrival alarms. 1.
104 Find Your Current Position Finding your current position is as simple as turning the unit on. Un- der clear sky conditions, the unit automatically searches for satellites and calculates its position in approximately one minute or less. NOTE: "Clear sky" means open sky, uno bstructed by terrain, dense foliage or structures.
105 The selected airport to the northwest is 4.25 miles away. Selecting Any Map Item With the Cursor 1. Use the zoom keys and the arrow keys to move around the map and find the item you wish to select. 2. Use the arrow keys and center the cursor cross-hair on the desired ob- ject.
106 Category Selection menu, left, and list of the nearest restaurants, right. 4. If you wish, you could scroll ↑ or ↓ here to select another restaurant, but for now we will just accept the nearest one. Press ENT . 5. The POI information screen appe ars.
107 Map screen showing Find Waypoint, the result of a restaurant search. 7. To clear the search and return to the last page displayed, press EXIT | EXIT | EXIT | EXIT . (Before you completely exited out of the Search menus, you could have gone looking for another place.
108 Sequence for setting a waypoint. Step 1: while traveling, quickly press WPT twice to call up Find Waypoint screen (seen in Step 2) and set a point. Step 3: a message says the waypoint has been saved. Step 4: ve- hicle continues on its way; number waypoint symbol is visible on map.
109 Create Waypoint by Entering a Position 1. Press WPT | → to S UBCATEGORY column| ↓ to N EW | ENT . 2. Press ↓ to E NTERED P OSITION | ENT | → to C REATE | ENT .
110 Navigation Page, navigating toward waypoint 004 and leaving a trail. Set Man Overboard (MOB) Waypoint One of boating's most terrifying even ts is having a friend or family member fall overboard. This situation can be deadly on any body of wa- ter — fresh or salt.
111 Navigating to Man Overboard: Navigation Page, left, and Map Page, right. The victim is astern of the vessel; the GPS shows which direc- tion to steer to for the rescue. The man overboard position is also st ored in the waypoint list for future reference.
112 Navigate to cursor. In this example, the cursor has selected the town of Oologah, Oklahoma. 3. Press MENU | ENT and the LCX-104C will begin navigating to the cur- sor location. The Map Page will display a red line from your current position to the cur- sor position.
113 Navigate to a Point of Interest For POIs that are in view on the map, you can easily use the Navigate to Cursor command above; just use the cursor to select the POI. The other method involves searchin g for POIs with the Find Waypoint command, launched with the WPT key.
114 Sequence for saving a trail and beginning a new one. At left, My Trails command. Center, the Trails Menu. The arrow to the right of Trail 17 indicates the trail is "active," and the check to the left indicates the trail is visible on the map display.
115 Tip: Another quick way to stop record ing one trail and begin a new one is to use the New Trail command: Press MENU | MENU | ↓ to M Y T RAILS | ENT | ENT . Caution: You also have the option of co mpletely turning off trail record- ing, under the trail Options command.
116 The other two methods provide a full ra nge of navigation data and work with both the Map Page and Naviga tion Page. The only difference be- tween them is "navigating a trail" follows a trail forward (from start to end) while "backtracking" follows a trail in reverse (from end to start.
117 Navigate a trail menu sequence: Fig. 1, My Trails command. Fig. 2, Trails Menu. Fig. 3, Edit Trail Menu. Fig. 4, Edit Route Menu with Navigate command highlighted for Trail 6. A trail is always converted to a "route" when you navigate the trail.
118 Navigate trail, map views: at left driver is northbound heading straight toward trail point 6. At right, northbound driver has reached point 6 and has turned west to follow trail.
119 NOTE: If you are already located at or near the end of your trail, the arri- val alarm will go off as soon as you hit Enter. Just press EXIT to clear the alarm and proceed. 5. Now, begin moving an d follow your LCX-104C. 6. When you reach your destination, be sure to cancel your navigation: press MENU | MENU | ↓ to C ANCEL N AVIGATION | ENT .
120 The Transfer My Data submenu asks if you want to save data to the MMC or load data from the MMC into the LCX-104C's memory. 2. The Transfer My Data menu incl udes a message which tells you if an MMC is present or not. If no MMC is present, you must first insert a card into the LCX-104C in order to activate the Load or Save commands.
121 4. Loading to unit memory : There may be more than one GPS Data File (*.USR) on the card. To select a file, press ENT to activate the selec- tion box, use ↓ or ↑ to highlight the file, then press ENT to accept the selection. Next, press ↓ to L OAD | ENT .
122 Notes.
123 Section 7: Advanced GPS Operations Find Distance From Current Position To Another Location 1. While on the Map Page press: MENU | ↓ to F IND D ISTANCE | ENT . 2. Center your cursor over the positi on you want to find the distance to. A rubber band line appears, connectin g your current position to the cursor's location.
124 called later for navigation purposes. These are sometimes referred to as event marker icons. The LCX-104C has 42 different symbols you can pick from when creating an icon. Icons are similar to waypoints, bu t they do not store as much informa- tion (like names) as waypoints do.
125 Delete icons menu. The Delete All Icons command will ask if you are sure. Press ← to Y ES | ENT . All icons will be deleted from the map. The Delete by Symbol command w ill launch the Select Symbol menu. Press ← or ↑ or → or ↓ to select the icon symbol to delete, then press ENT .
126 waypoint. Once programmed into the GPS unit, a route provides the option of navigating forward through the route waypoints or in reverse order (you can even begin navigating in the middle of a rou.
127 Edit Route menu, left. Edit Route Waypoints menu, right, with Add From Map command selected. 3. Use the Zoom keys and arrow keys to move the map and cursor until the cursor is centered on the spot where you want your route to begin.
128 5. Move the cursor to the next poin t in the route, a spot where you need to turn or change direction, and press ENT to set the next waypoint. 6. Repeat step five until the ro ute reaches your destination.
129 Edit Route Waypoints menu. 3. Use ↓ a n d ↑ to select a command from the Edit Route Waypoints menu and press ENT . Add From Map lets you insert a waypoint in the route by clicking on a map location with the cursor. Add Waypoint calls up the Waypoint List so you can in sert a waypoint from the list.
130 Navigate a Route in Reverse Here's how you run a route backward, from the end waypoint to the beginning waypoint: 1. From the N AVIGATION P AGE , press MENU | ENT or from the M AP P AGE , press MENU | MENU | ↓ to R OUTE P LANNING | ENT . 2.
131 Trails Delete a Trail This is the command used to erase or delete a trail: Press MENU | MENU | ↓ to M Y T RAILS | ENT | ↓ to trail name | ENT | → to D ELETE T RAIL | ENT | ← to Y ES | ENT . Tip: You can also delete all trails at once: 1. Press MENU | MENU | ↓ to M Y T RAILS | ENT .
132 then press → to the next character and repeat until the pattern is cor- rect. Press ENT , then EXIT | EXIT | EXIT | EXIT to return to the previous page display. At left, Edit Trail Menu with Pattern option selected. At right, edited trail with dotted line pattern.
133 To delete a waypoint from the map: 1. Use the arrow keys to sele ct the waypoint with the cursor. 2. Press WPT | → to D ELETE W AYPOINT | ENT | ← to Y ES | ENT .
134 accuracy by helping to eliminate errors caused by atmospheric condi- tions and other factors. 1. Press WPT | → to S UBCATEGORY column| ↓ to N EW | ENT . 2. Press ↓ or ↑ to A VERAGE P OSITION | ENT |press → to C REATE | ENT . 3. Wait while the unit takes points to average for the position.
135 Section 8: System & GPS Setup Options Alarms This unit has several GPS alarms. The factory default setting has all the alarms turned on. You can turn the alarms off and on and change their distance settings. You can set an arrival alarm to fla sh a warning message and sound a tone when you cross a preset distance from a waypoint.
136 4. When your adjustments are finishe d, return to the last page dis- played by repeatedly pressing EXIT . IMPORTANT ALARM NOTES: Anchor Alarm - The anchor alarm may be triggered even when you're sitting still. This typically happens when using small (less than 0.
137 GPS Auto Search on the Satellite Status Menu. You can force the unit to immediately kick into auto search mode. Here's how: 1. Press PAGES until you are on the Satellite Status screen. 2. Press MENU | ↓ to GPS A UTO S EARCH | ENT | ← to Y ES | ENT .
138 Menus for changing Com Port settings. For connectors and wiring information for another device, see page 33. For assistance in configuring the unit to communicate with another device, consult the factory; cus tomer service phone numbers are in the back of this manual.
139 Configure NMEA You can configure the unit to use specific NMEA sentences. 1. Press MENU | MENU | ↓ to S YSTEM S ETUP | ENT . 2. Press ↓ to C OMMUNICATIONS P ORT | ENT | ↓ to C ONFIGURE NMEA | ENT . 3. A menu appears showing the prefixes of the available NMEA sen- tences.
140 you must be in the respective count ry. This unit will pick the matching datum for you when you select the grid. See the entry on Map Datum Selection for more information. The military grid reference system (MGRS) uses two grid lettering schemes, which are referred to as standard and standard + 10 MGRS on this unit.
141 For example, if it shows a distance of UP 4.00" and LEFT 0.50", you then measure up four inches and to the left a half-inch from the refer- ence point on the map to find your location. To configure a map fix: To use this format, you need to follo w these steps in order.
142 Press ↓ to S ELECT O RIGIN W AYPOINT | ENT | ENT | ENT to bring up the way- point list. Select the waypoint that you saved the reference point under and press ENT . The unit displays a waypoint information screen with the command S ET A S O RIGIN selected; press ENT and the unit returns to the Configure Map Fix menu.
143 tion) or from a stored waypoint , map place or POI location ( C HOOSE S TART command). You can steer your positi on and change speed on the map by using the arrow keys ( S TEER WITH A RROWS command) or by setting the track and speed in the dialog boxes prov ided on the simulator menu screen.
144 3. Begin navigating along the trail/ro ute. (If you are close enough to the first waypoint, the arrival alarm will usually go off as soon as naviga- tion begins. Press EXIT to clear the alarm.) When navigation starts, press ↑ to increase speed to the desired setting.
145 Map Auto Zoom This receiver has an auto zoom feat ure that eliminates much of the but- ton pushing that other brands of GPS receivers force you to make. It works in conjunction with the navigation features. First, start navigation to a waypoint. (See the waypoint section for more information on navigating to a waypoint.
146 Pop-up Map Info From the Map Page, press MENU | ↓ to M AP D ATA | ENT . Press ↓ to P OPUP M AP I NFO . With the option highlighted, press ENT to check it (turn on) and uncheck it (turn off.) After the option is set, press EXIT | EXIT to re- turn to the page display.
147 Map Datum Selection Maps and charts are based on a survey of the area that's covered by the map or chart. These surveys are called "Datums." Maps that are cre- ated using different datums will sh ow the same latitude/longitude in slightly different locations.
148 Map Menu, left, Map Categories Drawn Menu, right. Map Orientation By default, this receiver shows the map with north always at the top of the screen. This is the way most ma ps and charts are printed on paper. Map orientation at left is shown in north up and at right, track up.
149 Map Menu, left; Map Orientation menu with the North Up map orientation option selected, right. Overlay Data To change the digital data shown on top of the Sonar Page or the Map Page: First, press PAGES , use → or ← to select a Page Name , then press EXIT .
150 Data list showing "Ground Speed" selected to display on Sonar Page. 3. To return to the previous page, press EXIT | EXIT . To turn off displayed data: 1. From the Map or Sonar page, press MENU | ↓ to O VERLAY D ATA | ENT . 2. Press ↓ or ↑ to select Data Type | ENT .
151 At left, Map Page showing boat cruising Puget Sound, Washington, with Overlay Data turned on. This example shows Depth, Ground Speed and the Steering Arrow. Note that the Steering Arrow always points directly to the destinatio n you are navigating toward.
152 2. From the Map Page, press MENU | ↓ to M AP D ATA | ENT | ↓ to M AP C HOICE | ENT . Use ↑ or ↓ to select the Map Name , then press ENT | EXIT | EXIT . These figures show menu sequence (from left to right) for selecting a Navionics chart for the South Chesapeake Bay area.
153 3. To scroll through the Service Categories window: press ENT then use ↑ or ↓ to see the types of services available. As you highlight a different category, the list in the lower window changes. To return to the Map Page, press EXIT | EXIT . 4.
154 Navionics chart showing Tidal Current Station icon selected by cur- sor. In this example, the tidal current is in flood but it's about to enter the slack water stage.
155 You can look up tidal current data for other dates by changing the month, day and year selection bo xes. To select another date: 1. Use → and ← to highlight month, day or year, then press ENT . 2. Use ↑ and ↓ to select the desired month, day or year, then press ENT .
156 Tide Information screen. The Tide Information screen displays daily tidal data for this station on this date at the present time. The gr aph at the top of the screen is an approximate view of the tidal range pattern for the day, from midnight (MN), to noon (NN) to midnight (MN).
157 System Setup menu, left, with Pop-up Help command highlighted. At right, this example shows the Pop-up Help message for the Screen command, located on the Map Menu. Position Pinning When you are standing still or moving at extremely slow speed, a GPS receiver can have trouble determin ing the direction you are traveling.
158 Reset Options command, left, and the Reset Options Menu, right. Require DGPS You can force the LCX-104C to requ ire DGPS for reporting a valid posi- tion. (The default setting, off, us es DGPS automatically when an op- tional DGPS beacon receiver is co nnected.
159 The C ONTRAST slider bar is already selected. Press → or ← to move the bar. The left end of the scale is minimum contrast; the right end is maximum contrast. Screen Command, left, and Screen Menu with Contrast bar selected, right. To adjust the display's brightness: Press ↓ to B RIGHTNESS .
160 1. Press MENU | MENU | ↓ to S YSTEM S ETUP | ENT . 2. Press ↓ to S ET L ANGUAGE … | ENT . 3. Use ↓ or ↑ to select a different language and press ENT . All menus now appear in the language you selected. Set Local Time Using the correct local time setting is handy when estimating local ar- rival time while navigating.
161 2. With the option highlighted, press ENT to uncheck it (turn off) and check it (turn on). After the option is set, press EXIT | EXIT to return to the page display.
162 Once in the Sounds menu: To set Key Press Sounds: With the option highlighted, press ENT to check it (turn on) and uncheck it (turn off). After the option is set, press EXIT | EXIT to return to the page display. To set Alarm Sounds: Press ↓ to A LARM S OUNDS .
163 Main Menu, left, Trails Menu, center, Trail Options, right. Delete All Trails To remove all of the trails from memory: from the Trails Menu, press → to D ELETE A LL | ENT | ← to Y ES | ENT . Update Trail Option This menu lets you change th e way the trail updates occur.
164 Trail Options menu: Update Time Rate setting, left, and Update Dis- tance setting, right. Specific Trail Options Delete Trail To delete a specific trail: From the Trails Menu, press ↓ to Trail Name | ENT . The Edit Trail menu appears as seen in the following fig- ure.
165 On the Edit Trail menu, press ↓ or ↑ to highlight the section you wish to change, then press ENT . Make your changes, then press EXIT to erase this menu. You can also change the trail line color and pattern. For instructions, see the entries on Edit a Trail Colo r and Edit a Trail Pattern beginning on page 131, Sec.
166 Notes.
167 Section 9: Searching NOTE: The background map loaded in your unit lets you search for U.S. Interstate Highway exits and exit services, as well as some land features, including cities and lakes.
168 Find Address Menu. 3. To enter an address number , press ↑ or ↓ to change the first number, then press → to move the cursor to the next number and re- peat until the number is correct, then press ENT . 4. To enter a street name , press ↓ to S TREET | ENT .
169 NOTE: We recommend that you do not enter a city name unless the list you are given is too large when search ing without it. The unit can actu- ally search quicker without a city and you save time by not entering a city name. Find city field, left, Search in particular city only option, center; Find City by name, right.
170 Tip: If the address also happens to be an item in the Point of Interest database, you can look up the it em's phone number in the Waypoint Information list. With the address lo cation selected by the cursor on the map, press WPT . The POI's Waypoint Information window ap- pears, with the Go To Waypoint command highlighted.
171 Find Interstate Highway Exits 1. From the Map Page, press MENU | ↓ to H IGHWAY E XITS | ENT , which calls up the Find Exit menu. Find Highway Exits command, left, and Find Exit menu, right. 2. First, select a highway name by pressing ENT , which calls up the Find By Name menu.
172 Find Exit menu, with an exit selected in the Exit List. 4. In the Exit Information screen you have two choices. A. Press ENT to navigate or "go to" the exit. B. Press → | ENT to find the exit on the map. "Go To Exit" option, left, "Find On Map" option, right.
173 Find Map Places or Points of Interest (POI) 1. Press WPT , press ↓ or ↑ to select a map place or POI category, then press ENT . (To narrow your search, press → then press ↓ or ↑ to s el ec t a subcategory before pressing ENT .) You will be given two options; Search By Name or By Nearest.
174 Find by Name option, left, Find by Name menu, right. 4. When the POI's Waypoint Information screen is displayed, you can choose to "Go To" the POI waypoint by pressing ENT or find it on the map by pressing → | ENT . Go To Waypoint POI option, left; Find on Map POI option, right.
175 2. You must first fill in a street name in the First Street dialog box. Press ENT to display the Find By Name menu. There are two options: A. You can spell out the street in the top selection box.
176 Map Page showing results of a street search. The cursor points to the located street. If you want to navigate to the found street at the cursor location, just press MENU | ENT | EXIT . Find an Intersection You must enter one street in the Firs t Street dialog box and enter the next street in the Second Street dialog box.
177 5. The Find Streets menu reappears with the first and second street dialog boxes filled in. In this example, we selected 71st Street as our second street. You could now use sim ilar techniques to select a city or Zip code, but your search will probably be faster if you leave those boxes blank.
178 Find Waypoints 1. Press WPT | ENT . 2. If searching for the waypoint By Name , press ENT . If searching for the Nearest waypoint, press ↓ to N EAREST | ENT . (To search by name, jump to step 5 below.) Find Waypoint menu, left; Find By Nearest command, center, Find by Name command, right.
179 Waypoint Information screens with the Go To Waypoint command se- lected, left, and the Find on Map command selected, right. To clear these menus and return to the previous page, press EXIT re- peatedly. 5. If you're looking by name , there are two options: A.
180 Notes.
181 Section 10: Supplemental Material Datums Used by This Unit WGS 1984 Default Adindan Mean for Ethiopia, Sudan Adindan Burkina Faso Adindan Cameroon Adindan Ethiopia Adindan Mali Adindan Senegal Adi.
182 DOS 1968 New Georgia Islands (Gizo Island) Easter Island 1967 Easter Island European 1950 Mean for Austria, Belgium, Denmark, Finland, France, West Germany, Gibraltar, Greece, Italy, Luxembourg, N.
183 North American 1927 Mean for CONUS (Continental United States) North American 1927 Mean for CONUS (East of Mississippi River) including Louisiana, Missouri, Minnesota North American 1927 Mean for .
184 Bolivia, Brazil, Chile, Colombia, Ecuador, Guyana, Paraguay, Peru, Trinidad & Tobago, and Venezuela South American 1969 Argentina South American 1969 Bolivia South American 1969 Brazil South A.
185 FCC Compliance This device complies with Part 15 of the U.S. Federal Communications Commission (FCC) Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
186 Notes.
187 LOWRANCE DATABASES LICENSE AGREEMENT THIS IS A LEGAL AGREEMENT BETWEEN THE END-USER WHO FIRST PURCHASES THIS PRODUCT AS A CONSUMER ITEM FOR PERSONAL, FAMILY, OR HOUSEHOLD USE ("YOU") AND LOWRANCE ELECTRONICS, INC., THE MANUFACTURER OF THIS PRODUCT ("WE", "OUR", OR "US").
188 DATABASES LIMITED WARRANTY "We", "our", or "us" refers to Lowrance Electronics, Inc., the manufacturer of this product. "You" or "your" refers to the first person who purchases the product as a consumer item for personal, family, or household use.
189 LOWRANCE ELECTRONICS FULL ONE-YEAR WARRANTY "We," "our," or "us" refers to LOWRAN CE ELECTRONICS, INC ., the manufacturer of this product. "You" or "your" refers to the first person who purchases this product as a consumer item for personal, family or household use.
190 How to Obtain Service… …in the USA: We back your investment in quality pr oducts with quick, expert service and genuine Lowrance parts. If you' re in the United States and you have technical, return or repair qu estions, please contact the Factory Customer Service Department.
Accessory Ordering Information for all countries To order Lowrance accessories such as cables, transducers or MMC cards, please contact: 1) Your local marine de aler or consumer electr onics store. Most quality dealers that han dle marine electronic equipment or other consumer electronics should be a ble to assist you with thes e items.
Visit our web site: Lowrance Pub. 988-0151-031 © Copyright 2002 All Rights Reserved Printed in USA 122002 Lowrance Electronics, Inc..
デバイスLowrance electronic LCX-104Cの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Lowrance electronic LCX-104Cをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはLowrance electronic LCX-104Cの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Lowrance electronic LCX-104Cの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Lowrance electronic LCX-104Cで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Lowrance electronic LCX-104Cを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はLowrance electronic LCX-104Cの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Lowrance electronic LCX-104Cに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちLowrance electronic LCX-104Cデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
