Lucent Technologiesメーカー308/616の使用説明書/サービス説明書
ページ先へ移動 of 20
Lucent Technologies Bell Labs Innovations SPIRI T ® Communications System Model 308/616 Customer Installation Instructions 999-500-226 105772578 Issue 4 June 1989.
Intellectual property related to this product and registered to AT&T Corporation has been transferred to Lucent Technologies Incorporated. Any references within this text to American Telephone and Telegraph Corporation or AT&T should be interpreted as references to Lucent Technologies Incorporated.
INTERFERENCE INFORMATION FCC REGULATIONS PERTAINING TO THIS EQUIPMENT NOTICE Federal Communications Commission (FCC) rules require that you be notified of the following: FCC (Part 15) This equipment g.
TABLE OF CONTENTS Introduction 2 Overview of System 2 Step 1 Plan Your System 3 Step 2 Check Outlet Grounding 3 Step 3 Mount Controller 4 Mount Controller on Wall 4 Test the Incoming Telephone Lines 5.
Introduction This instruction manual will show you how to install your SPIRIT Communications System. Please read the instructions carefully before beginning installation.
Step 1 Plan Your System Draw a floor plan of your business, showing the location of the network interface jacks, where your local telephone lines come into the building. You will want to install your controller close to these jacks. Show on the floor plan the location of each telephone in your system.
Step 3 Mount Controller ■ Mount Controller on Wall Choose a location within five feet of the network interface jacks, where the local telephone company lines enter the building, and near an AC outlet that is not controlled by a switch.
■ Test the Incoming Telephone Lines. TEST: If you have a standard telephone with a modular cord, plug it into each jack of the network interface, or incoming telephone lines. If these jacks do not work you will require service by your local telephone company.
Step 4 Wiring Runs You may choose to wire your SPIRIT Communications System using 4-pair “business” wiring materials or 2-pair “customer convenience” wiring materials. While the materials are somewhat different, the procedure for labeling the wiring run is the same.
Step 4A Business (4-pair) Wiring You may choose to wire your business with 4-pair “business” wiring to be ready for future communications systems. You will need the following materials: ❑ screwd.
■ Mount Jack Panel Boxes Mount the jack panel boxes near the controller, creating a “jack field.” You will need one jack panel box for every six telephones in your system. Ideally, the jack field will be two to six inches below the controller if the controller is wall-mounted.
■ Run Cable To All Telephone Locations Select a cable extension kit with the right length of cable (100 or 200 feet) for one cable run. For runs over 200 feet, run a 200-foot cable, terminate it in a modular connecting block, plug in another cable, and repeat, up to a maximum of 1000 feet.
■ Install Modular Connecting Blocks Install a modular connecting block at each telephone location Find the modular connecting block from the Cable Extension Kit and the cable installation tool from the Wiring Installation Kit. Choose the location for the connecting block according to the figure.
Typical cable installation for one telephone location. Cable clip Identical labels Cable TELEPHONE LOCATION Modular connecting block Finish your installation by routing cables to all other telephone locations and installing modular connecting blocks for each one.
Step 4B Wiring Run, Using Customer Convenience Wiring Customer convenience wiring materials are available at your local phone store. Different situations require different materials.
Typical Installation Using Customer Convenience Wiring Sample System Directory Label Controller 10 11 12 13 700A4 PLUG Telephone Labels 630B Wall Connecting Block Wire Run Greater Than 50’ Telephone Set Modular Cord (D4BU) 25’ Max.
Step 5 Install Telephone Sets SPIRIT telephone sets are available in 6-Button and 24-Button models. The models are installed the same way. SPIRIT telephones are not like regular telephones and will not work if plugged directly into the Network Interface Jacks.
Step 6 Connect System To Wiring Runs Connect the controller to the wiring runs. Following the numbers on your wiring run labels, plug one end of a jumper cord into the jack panel box or wire junction (see pages 7 and 14) and the other end of the jumper cord into the appropriate station jack on the controller.
3. The left INTERCOM light should be lit if there is a 616 expansion unit installed correctly. If there is not an expansion unit installed, and the light does light, then there is a defect in the 308 controller.
Troubleshooting What To Do If You Have Trouble With Your System: For SPIRIT Communications Systems purchased from AT&T, a customer “hotline” (1-800-628-2888) is available to help you if you have questions about or trouble with your system.
デバイスLucent Technologies 308/616の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Lucent Technologies 308/616をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはLucent Technologies 308/616の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Lucent Technologies 308/616の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Lucent Technologies 308/616で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Lucent Technologies 308/616を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はLucent Technologies 308/616の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Lucent Technologies 308/616に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちLucent Technologies 308/616デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
