Lux ProductsメーカーPSPU732Tの使用説明書/サービス説明書
ページ先へ移動 of 48
3-YEAR WARRANTY INSTRUCTION MANUAL LUXPRO ® PSPU732T 3 Heating and 2 Cooling with Automatic Humidity Control and Dual Fuel Switch LUX Products Corporation 6000 Commerce Parkway , Suite-I • Mt. Laurel, NJ 08054 (856) 234-7905 • F AX (856) 234-7825 http://www.
2 LUXPRO ® PSPU732T.
O O U U T T D D O O O O R R W W I I R R E E L L E E S S S S T T E E M M P P E E R R A A T T U U R R E E T T R R A A N N S S M M I I T T T T E E R R A A N N D D R R E E C C E E I I V V E E R R K K I I T T LUXPRO ® Part No.
LUXPRO ® PSPU732T Introducing the LUXPRO ® PSPU732T touch-screen thermostat with 3-stage heating, 2-stage cooling control, an automatic humidity controller and fossil fuel switch (Available only when combined with LUXPRO ® Outdoor Wireless T ransmitter and Receiver Kit.
T ABLE OF CONTENTS ...................................................................................................................5 GLOSSARY OF TERMS .................................................................................................
GLOSSAR Y OF TERMS 6 LUXPRO ® PSPU732T CYCLE RA TE - Cycle rate is the frequency that heating or cooling equipment is turned on during a certain period of time. Cycle rate is often given in units of cyc les per hour (CPH). DEHUMIDIFY - The process of removing moisture from the air .
Install your LUXPRO ® thermostat approximately 5 feet (1.5 meters) above the floor in an area with good air circulation. Avoid the following locations: • Hot or cold air from ducts • Radiant heat for appliances or sun such as a skylight • Unheated or uncooled areas: for example an outside wall behind the thermostat.
MOUNTING THE THERMOST A T TO THE WALL 8 LUXPRO ® PSPU732T 1. Make sure to turn off the power supply located at the electrical ser vice panel. All heating and cooling units should be OFF . 2. Separate the backplate from the thermostat by grasping the unit firmly a t the bottom lip and pulling gently until the two piece are apart.
TERMINAL EQUIPMENT ST ANDARD COLOR Y1 First Heat Pump and AC Y ellow G Fan Green W2 First Stage Furnace White OBW Reverse Valve - Second Stage Furnace Orange RH 24v Red Y2 Second Heat Pump and AC Unkn.
WIRING DIAGRAMS 10 LUXPRO ® PSPU732T I2 1 AIR CONDITIONER 24V FAN AC I1 RC DH H C Y2 RH OBW W2 G Y1 COMMON COOL 2 I2 2 STAGE COOL 24V FAN COOL 1 I1 RC DH H C Y2 RH OBW W2 G Y1 COMMON.
HEAT 2 HEAT 1 I2 1 AIR CONDITIONER AND 2 STAGE HEA T 24V FAN AC I1 RC DH H C Y2 RH OBW W2 G Y1 COMMON HEAT I2 1 AIR CONDITIONER AND 1 STAGE HEA T 24V FAN AC I1 RC DH H C Y2 RH OBW W2 G Y1 COMMON WIRIN.
HEAT REVERSE VAL VES I2 1 HEA T PUMP AND 1 STAGE HEA T 24V FAN HP I1 RC DH H C Y2 RH OBW W2 G Y1 COMMON REVERSE VAL VES I2 1 HEA T PUMP 24V FAN HP I1 RC DH H C Y2 RH OBW W2 G Y1 COMMON WIRING DIAGRAMS.
WIRING DIAGRAMS 13 INSTRUCTION MANUAL I2 COMMON 2 HEA T PUMPS HP2 24V REVERSE VAL VES FAN HP1 I1 RC DH H C Y2 RH OBW W2 G Y1 I2 COMMON 1 HEA T PUMP AND 2 STAGE HEA T HEAT 2 24V REVERSE VAL VES HEAT 1 .
HEAT TRANSFORMER COOL TRANSFORMER I2 2 TRANSFORMERS I1 RC DH H C Y2 CUT RH OBW W2 G Y1 I2 1 TRANSFORMER I1 RC DH H C Y2 RH OBW W2 G Y1 HEAT TRANSFORMER WIRING DIAGRAMS 14 LUXPRO ® PSPU732T.
WIRING DIAGRAMS 15 INSTRUCTION MANUAL I2 HUMIDIFIER WITHOUT TRANSFORMER 24V I1 RC DH H C Y2 RH OBW W2 G Y1 HUMIDIFIER 2nd WIRE HUMIDIFIER 1st WIRE.
Current Room T emperature Current Room Humidity Current Outdoor T emperature Current Thermostat Operation Mode Current T emperature Control Mode Current Fan Operation Mode Fan Operation Indicator Vaca.
Change the T emperature Setpoint(s) using - and + buttons. In AUTO MODE toggle the Heat/Cool button (Hea t or Cool will flash once selected), then raise or lower setpoints as desired. Change the Humidity Setpoint using - and + buttons. Select the Thermostat Opera tion Mode by toggling thermostat operation mode button.
THERMOST A T OPERA TION MODES 18 LUXPRO ® PSPU732T > > LUXPRO ® thermostat can operate in PROGRAM MODE or can HOLD a fixed temperature. RUN PROGRAM : the thermostat initiates the 7-day Programmable T emperature Control Program with 4 independent events per day .
> > Based on your HVAC equipment LUXPRO ® thermostat can operate in the following tempera- ture control modes - AUTO or HEA T or EMERGENCY HEA T or COOL or OFF AUTO - the thermostat keeps the room temperature between the selected HEA T and COOL setpoints by using both the cooling and heating HVAC units.
AUTOMA TIC HUMIDITY CONTROL 20 LUXPRO ® PSPU732T > > In order to reduce condensation, humidity must be controlled and air mo vement must be generated. As the exterior temperature drops, the humidity level needs to decrease if condensation is to be controlled.
> > HUMIDIFY SETPOINT : Allows you to increase and maintain the relative humidity at a specif- ic setpoint. Once you choose HUMIDIFY follow these easy steps: • The HUM setpoint with - and + icons allow you to lower and raise your setpoint.
DE-HUMIDIFY AND HUMIDITY SETPOINT 22 LUXPRO ® PSPU732T > > DE-HUMIDIFY SETPOINT : Allows you to reduce and maintain the rela tive humidity at a specific setpoint.
F AN OPERA TION MODES 23 INSTRUCTION MANUAL > > LUXPRO ® thermostat can operate the fan in one of the following three modes: F AN AUTO : The fan runs only when there is a demand for heating or cool- ing.
MENU SCREEN 24 LUXPRO ® PSPU732T > > T o access the MENU SCREEN, simply touch MENU from the CONTROL SCREEN. > > From the MENU page, you can: Access DA TE AND TIME SETTINGS to enter the accurate date and time Access PROGRAM SETTINGS to pre-program temperature changes during each day of the week.
MENU SCREEN Select HUMIDIFY or DE-HUMIDIFY Control Mode by toggling the humidity control mode button. HUMIDIFY increases and maintains the relative humidity of the room at a humidity setpoint selected on the CONTROL SCREEN. DE-HUMIDIFY reduces and maintains the relative humidity of the room at a humidity setpoint selected on the CONTROL SCREEN.
26 LUXPRO ® PSPU732T D A TE AND TIME SETTINGS Select the 12 OR 24 HOUR CLOCK display by pushing the corresponding button. Set the TIME by togggling hour , minute and AM/PM buttons.
PROGRAM SETTINGS PROGRAM SETTINGS feature allows you to easily and quickly program daily temperature changes to fit your lifestyle and reduce energy con- sumption. Y ou can customize the program for each day of the week with 4 independent temperature and fan operation settings per day.
28 LUXPRO ® PSPU732T ENERGY W A TCH ENERGY WA TCH feature provides a report on the energy consumption and the dollar cost of operating your HVAC system (for up to the last 255 days).
SET SCREEN OPTIONS • BACKLIGHT : Select between automatic and permanent backlight for the screen. AUTO: The screen back-light will come on only when you touch the screen. ON: Screen will constantly be back-lit. • REVERSE : Select the positive or negative screen display .
30 LUXPRO ® PSPU732T V AC A TION MODE > > V ACA TION SETTINGS allows you to set the temperature to a fixed setpoint during the time you are on vacation, providing energy savings without compromising comfort upon your return. IMPORT ANT : HEA T or COOL must be selected from the CONTROL SCREEN before entering the Vacation Settings screen.
FIL TER MONITOR FIL TER MONITOR: Displays filter usage in days RESET : Resets filter timer (Y ou should reset FIL TER MONITOR after chang- ing the air filter . When activated the FIL TER MONITOR icon appears on your HOME SCREEN - this feature must be activated in ADV ANCED SETTINGS.
• DA YLIGHT TIME : Choose Daylight Time ON or OFF dependent on your Time Zone. FIL TER: Enter the air filter "fan run time" infor- mation here. The Filter Monitor feature uses this information to inform you when to change your air filter by displaying CHANGE FIL TER icon on the HOME SCREEN.
SECURITY : The security settings allow you to protect your LUXPRO ® thermostat from unautho- rized use. T urn Security ON or OFF . Y ou will be prompted to enter the PIN. The Default PIN 1111. To CHANGE PIN , enter your new PIN and then, when prompted, re-enter your new PIN.
ADV ANCED SETTINGS - SY STEM CONFIGURA TION 34 LUXPRO ® PSPU732T ! IMPORT ANT : By inadvertently modifying system configuration settings, you may seri- ously degrade HV AC system performance. > > Choose system heating and cooling equipment - remember all you need to do is toggle the appropriate button until the correct setting appears.
! IMPORT ANT : This feature can only be activ ated when used with the LUXPRO ® Outdoor Wireless T emperature T ransmitter and Receiver . Please install the LUXPRO ® Outdoor Wireless T emperature T ransmitter and Receiver before activ ating this feature.
ADV ANCED SETTINGS - DIFFERENTIAL SETTINGS 36 LUXPRO ® PSPU732T > > LUXPRO ® PSPU732T allows you to control up to 3 Stages of Heating and 2 Stages of Cooling, dependent on the type of system you have configured.
• Specify the number of minutes for which Stage 1 will function until Stage 2 is activated to help raise (or cool) temperature (if the temperature set point is not reached). This unique function avoids excess compressor wear in the case where the necessary tempera ture set point is not met through setting of the Staging Differential.
ADV ANCED SETTINGS - HEA T PUMP 38 LUXPRO ® PSPU732T • HP ON when Furnace On: Hea t Pump and Furnace can operate together when 2nd stage fur- nace is required. HP “OFF” when Furnace On: turns off the Heat Pump when the furnace is On (required on some gas or oil furnaces).
> > IMPORT ANT : The Automatic Humidity Control feature can only be activated when used with the LUXPRO ® Outdoor Wireless T emperature T ransmitter and Receiver . Please install the LUXPRO ® Outdoor Wireless T emperature T ransmitter and Receiver before activ ating this feature.
ADV ANCED SETTINGS - HUMIDITY SETTINGS 40 LUXPRO ® PSPU732T > > Operating Tips • HUMIDIFICA TION F AN should be set to ON when running steam or mist humidifiers. • HUMIDIFICA TION F AN should be set to OFF when running drum humidifiers or any other humid- ifier that requires the furnace to run in order to make humidity .
> > De-humidification options for increasing comfort and efficiency • HRV/ERV units can be controlled by simply connecting the DH terminal on the thermostat to the terminal DH of the HRV/ERV . Most HRV/ERV units will control properly with the DH REVERSE fea- ture turned off (contact normally open).
ADV ANCED SETTINGS - C ALIBRA TION 42 LUXPRO ® PSPU732T > > Calibration of T emperature or Relative Humidity Y our LUXPRO ® thermostat is rated for ±1°F (±0.
> > T emperature Calibration T able • Determine the temperature difference using an accurate thermometer and use the following table to calibrate your thermostat. The thermostat temperature reading can be calibra ted by ±19°F (±9.5°C). ADV ANCED SETTINGS - C ALIBRA TION 43 INSTRUCTION MANUAL Calibration Number °C Change °F Change ±0.
SIMPLE THERMOST A T MODE 44 LUXPRO ® PSPU732T > > LUXPRO ® thermosta t can also function as a virtual non-programmable thermostat after it has been switched to a “SIMPLE MODE”.
? T ouch screen buttons do not function properly . Remove cover , press the reset button loca ted in the bottom left corner then accurately touch 3 target centers on the screen when prompted. ? Air Conditioning does not turn on even when room temperature is higher then the temper- ature set point set point .
IMPOR T ANT NO TICE 46 LUXPRO ® PSPU732T > > WHEN USING THIS THERMOST AT WITH A GAS FURNACE A COMMON WIRE (C) MUST BE CONNECTED. When working without a common wire: > > A confirm in HEA T MODE the cooling does not switch on or B confirm in COOL MODE the hea t do- es not switch on.
HARDWARE LUX Products Corporation warrants the original end user (“Customer”) that new LUXPRO ® branded products will be free from defects in workmanship and materials, under normal use, for three (3) years from the original purchase date.
FCC ST A TEMENT THIS DEVICE COMPLIES WITH PAR T 15 OF THE FCC RULES. OPERA TION IS SUB- JECT TO THE FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MA Y NOT CAUSE HARMFUL INTER- FERENCE, AND (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTER- FERENCE THAT MA Y CAUSE UNDESIRED OPERA TION.
デバイスLux Products PSPU732Tの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Lux Products PSPU732Tをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはLux Products PSPU732Tの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Lux Products PSPU732Tの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Lux Products PSPU732Tで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Lux Products PSPU732Tを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はLux Products PSPU732Tの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Lux Products PSPU732Tに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちLux Products PSPU732Tデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
