MagnadyneメーカーM11RF-LCDの使用説明書/サービス説明書
ページ先へ移動 of 20
User’ s Manual Model: M11RF-LCD T wo-Way Communication LCD T ransmitter 4/5/6 5 4 C For T echnical Assistance, please call (800) 638-3600, or visit www .
The remote control is powered by a 1.5V type AAA Alkaline battery . When the power of the battery weakens the battery icon will be displayed on the LCD screen. When the old batter y is replaced with a new one, there will be a beep to indicate the power is up and the clock on the LCD screen returns to AM12:00 after displaying all the icons.
3 Remote Control T ransmitters Operation T ransmitter Button System Function Remark Lock Doors & Arm System Panic Function Press and Hold for 3 Seconds Car Locator Under Armed Mode Arm and Delete .
4 LCD Display T ransmitter Operations T ransmitter Button System Function Remark SET (C) Systems T rigger Record Check Press within 3 Seconds SET SET (C) System’ s Status Check Press within 3 Second.
5 LED Display Parking Light System Characteristics Siren/Horn Parking Light LED Doors Starter Dome Light 1. Arming 1 or 3 Chirps 1 Flash Slow Flash Locking Disabled 2. Disarming 2 or 4 Chirps 2 or 3 Flashes Unlocking T urns on for 30 Seconds 3. T rigger Alarming Flashes Slow Flash Disabled Flashes 4.
6 Active Arming: Lock & Arm 1. Press the button on the transmitter . 2. The siren will chirp once and parking lights will flash once indicating that the system is now armed. The vehicle door will lock upon arming when interfaced with the security system.
7 Active Disarming Unlock & Disarm 1. Press the button on the transmitter . 2. The siren will chirp twice and parking lights will flash twice indicating that the system is now disarmed. The vehicle door will unlock and the dome light will turn on for 30 seconds upon disarming when interfaced with the security system.
The valet switch allows you to temporarily bypass all alarm functions eliminating the need to hand your transmitter to parking attendants or garage mechanics. When the system is in valet mode, all alarm functions and remote start functions are bypassed, however the remote panic feature and remote door locks will remain operational.
T rigger the System (Continued) Ignition T rigger (Clear the Flash Icon and Melody Sound): When the Security System is triggered, the LCD screen will alert the user through melody sound and flashing icons. By pressing the “SET” button 3 times within 3 seconds it will clear the flashing icons and stop the melody sound.
Anti-Car Jacking (Continued) T rigger the Anti-Car Jacking Mode Three Timer cir cuits will function as follows: First Timer Circuit 1. 50 seconds after the car jacking mode has been activated, the siren will begin to sound for 15 seconds.
Dome Light Supervision The Security System has a unique feature for using your vehicle’ s dome light. 1 . Upon disarming the vehicles security system, the interior dome light will remain on for thirty seconds. 2. If the security system is triggered, the dome light will flash for the same duration as the horn/siren.
Remote Start Operation T o Remote Start Y our Vehicle by Using the Remote T ransmitter: 1. Press the button twice on the remote transmitter . 2. The parking lights will turn “ON” to indicate the remote start is activated. 3. The engine will start in approximately 5 seconds.
Timer Start: This unit can be programmed to start and run the engine every 3 hours, 2 hours or punctually at the same time every morning. The engine will run for the programmed running time and then shut down. Important! Timer start should be used only in open areas.
Interference 4/5/6 5 4 C SET Bi 6 Note: The transmission range may become shorter if the system is interfered by a stronger radio frequency from sources of high voltage electric power or obstacles like tall buildings. The transmitter uses low output powered frequency .
Door Lock Lock your Vehicles Doors Door Unlock Unlock your Vehicles Doors Armed Mode Security System is Armed Valet Mode Security System is Armed Remote T ransmission T ransmitting a Signal In-Range I.
16 Screen Lamp On: Press and hold the “SET” button one second, with the melody sound and the LCD screen lamp will turn on for 5 seconds. Power Save Mode: While in the Power Save Mode, the LCD transmitter uses “0” current to save the battery power .
Vibration/Melody Mode: This mode is useful when you are in a noisy place and it is difficult to hear the beep from the remote. The LCD transmitter will vibrate if your security system has been activated. Press the “SET” button first, within 3 seconds press the ( ) button for 2 seconds to select the mode of vibrate/melody .
18 Replacement Parts and Accessories 4/5/6 5 4 C 5-Button Transmitter for M11a Security System. M11RF-LCD 139.95 ea. 4-Button Transmitter with SAW Technology for M11RF 59.95 ea. M11a Security System. TRANSMITTERS DESCRIPTION MODEL # $ PRICE BATTERIES 1.
Credit Card or Money Order Only (Sorry No Cash, C.O.D. or personal checks accepted) SHIP TO: (No P .O. Boxes) LAST NAME FIRST NAME INITIAL STREET ADDRESS ADDITIONAL ADDRESS ADDITIONAL ADDRESS CITY ST A TE ZIP CODE DA Y TIME PHONE NUMBER PAR T # DESCRIPTION QTY .
M11RF-LCD-UM 2-10-04 Rev. A © Copyright 2004 Magnadyne Corporation Limited Lifetime Warranty Magnadyne Corporation or its authorized agents will, for the life of the vehicle and to the original purch.
デバイスMagnadyne M11RF-LCDの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Magnadyne M11RF-LCDをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはMagnadyne M11RF-LCDの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Magnadyne M11RF-LCDの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Magnadyne M11RF-LCDで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Magnadyne M11RF-LCDを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はMagnadyne M11RF-LCDの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Magnadyne M11RF-LCDに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちMagnadyne M11RF-LCDデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
