MAGNEPLANARメーカーMG3.6/Rの使用説明書/サービス説明書
ページ先へ移動 of 14
MAG NEP LANA R® MG3. 6/R Instruction Manual MAGNEPLANAR® PRODUCTS WHITE BEAR LAKE, MINNESOTA 55110 www .ma gne pan .com.
1. INTRODUCTION Congratulations on your purchase. The Magneplanar MG3.6/ R loudspeaker was conceived and designed for perfectionists. One of the most revealing loudspeakers made, it will provide outstanding music reproduction when used with high quality components.
5. PACKAGING Save all packaging, including the protective cover for the ri bbon tweeters. If you need to transport the speakers, they can be shipped safely only in t he original packaging. You may never have to return your speakers, but should the occasion arise, they should not be shipped in any packaging but the original.
7. HOOKUP This section covers amplification with a single stereo ampl ifier. For instruction on bi- amplification or bi-wiring, refer to Sections 11 and 12. DIRECT-CONNECT CROSSOVER INSTALLATI ON A. Insert the small connectors in the fou r output ports of the crossover box, using a 5/64" hex wrench.
.
FUSING – The mid and treble sectio ns of the MG3.6/R are protected with Type SAG normal blow fuses (4 amp for midrange; 2-1/2 amp for tweeter). The bass section does not require fusing protection. The fuse values should never be increased or bypassed.
.
Figure 5 STEREO WIDTH AND IMAGING Once you have located the best position for the speakers and your chair for good bass performance, separate the t weeters by 50% of the distance from your chair to the speakers. (For example, if your chair is 10 feet from the speakers, move the tweeters 5 feet apart.
9. ROOM ACOUSTICS Magneplanars, like other bipolar speakers, usually sound best wi th a moderately reflective surface behind the speakers. In situations where the speakers must be placed closer than 2 feet from the back wall, a heavy da mping material directly behind the speakers is advised; however, it should not cover the entire wall.
11. BI-AMPLIFICATION WITH CONVENTIONAL ELECTRONIC CROSSOVER The MG3.6/R is arranged conveniently for bi-amplificat ion. By adding an additional stereo amplifier and a crossover, you can enjoy the ben efits of increased dynamic range and lower distortion.
12. BI-WIRING OPTION Bi-wiring requires two sets of speaker cables. They may be identical or one set may be specialized for high frequencies and the other specialized for low frequencies. A. Remove both jumpers on the crossover box. B. Connect one set of cables to the lo w cable input and the other set to the high cable input.
15. THE RIBBON TWEETER Because the foil element in your MG3.6/R line source t weeter is only .00015 inches thick, it is very fragile. It's the price we pay for ultra-high performance.
16. 60" VERSION 2 RIBBON TWEETE R REPLACEMENT Tools Needed: #2 Phillips Screwdriver Needle Nose Pliers 1. Place protective cover over backside of ribbon tweeter, as shown (to prevent damage to ribbon while moving the spea ke r pa nel ). 2. Carefully lay speaker on a flat table or work in g su rfa ce.
17. MG3 .6/ R SP ECI FICA TIO NS SYSTEM DESCRIPTION: 3-Way True Ribbon Twe eter, Planar-Magnetic Midrange and Bass with Bi-Amplification Option BASS SECTION: 500 Sq.
デバイスMAGNEPLANAR MG3.6/Rの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
MAGNEPLANAR MG3.6/Rをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはMAGNEPLANAR MG3.6/Rの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。MAGNEPLANAR MG3.6/Rの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。MAGNEPLANAR MG3.6/Rで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
MAGNEPLANAR MG3.6/Rを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はMAGNEPLANAR MG3.6/Rの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、MAGNEPLANAR MG3.6/Rに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちMAGNEPLANAR MG3.6/Rデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
