Makitaメーカー6093Dの使用説明書/サービス説明書
ページ先へ移動 of 16
Cordless Driver Drill Capacities Steel Wood Wood screw Machine screw 10 mm 18 mm 5.5 mm x 55 mm 6 mm 1318") I1 Jj16"l 17/32" x 2-1j8"l 115164") Equipped with Electric Brake 10 mm (3/8") MODEL 60930 10 mm (3/8") MODEL 6093DW Dimensions Net IL x W x HI 265 mm x 58 mm x 262 mm No load speed weight 1.
IMPORTANT SAFETY IN STRU CTlO N S (For All Tools) WARNING: WHEN USING ELECTRIC TOOLS, BASIC SAFE- REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, AND PER- TY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO SONAL INJURY, INCLUDING THE FOLLOWING: READ ALL INSTRUCTIONS.
14. REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking to see that keys and adjusting wrenches are removed from tool before turning it on. 15. AVOID UNINTENTIONAL STARTING. Don't carry plugged-in tool with finger on switch. Be sure switch is OFF when plugging in.
IMPORTANT SAFETY 1. SAVE THESE INSTRUCTIONS - This manual contains important safety and operating instructions for battery charger. 2. Before using battery charger, read all instructions and cautionary markings on (1) battery charger, (2) battery, and (3) product using battery.
ADDITIONAL SAFETY RULES FOR CHARGER & BATTERY CARTRIDGE 1. Do not charge Battery Cartridge when temperature is BELOW 10°C (5OOF) 2. Do not attempt to use a step-up transformer, an engine generator or DC power 3. Do not allow anything to cover or clog the charger vents.
Installing or removing battery cartridge *Always switch off the tool before insertion or removal of the battery cartridge. .To remove the battery cartridge, pull out the set plate on the tool and grasp both sides of the cartridge while withdrawing it from the barrel.
0 If you wish to charge two battery cartridges, allow 15 minutes between chargings on the fast charger. Installing or removing drill bit or driver bit CAUTION: Always be sure that the tool is switched off and the battery cartridge is removed before installing or removing the bit.
Switch action Tool speed is increased by increasing pres- sure on the trigger. To start the tool, simply pull the trigger. Release the trigger to stop. CAUTION : Before inserting the battery cartridge into the tool, always check to see that the trigger switch actuates properly and returns to the "OFF" position when released.
Adjusting fastening torque I I The fastening torque can be adjusted in six stages by turning the adjusting ring so that the pointer on the adjusting ring points to a number on the tool body. The fastening torque is minimum when the pointer points to the number 1 and maximum when it points to the -8- marking.
NOTE : 0 Use the proper bit for the head of the screw that you wish to use. 0 Make sure that the driver bit is inserted straight in the screw head, or the screw and/or bit may be damaged. 0 When driving wood screws, predrill Pilot Nominal diameter of I Recommended size holes to make driving easier and to pre- vent splitting of the workpiece.
Overload protector The overload protector automatically cuts out to break the circuit whenever heavy work is prolonged. Wait 20 -30 seconds before resuming operation. Recycling the Battery The only way to dispose of a Makita battery is to recycle it. The law prohibits any other method of disposal.
MAINTENANCE CAUTION : Always be sure that the tool is switched off and the battery cartridge is removed before attempting to perform inspection or maintenance. To maintain product SAFETY and RELlABl LITY, repairs, maintenance or adjustment should be performed by Makita Authorized or Factory Service Centers, always using Makita replacement parts.
OPTIONAL ACCESSORIES The accessories listed in this manual are available at an extra cost from your Makita distributor or Makita factory service center. Service centers are listed on the warranty card packed with your tool. CAUTION : These accessories or attachments are recommended for use with your Makita tool specified in this manual.
Dec 25-'86 EN 10 mm (318") CORDLESS DRIVER DRILL Model 6093D Note: The switch and other part configurations may differ from country to country.
MODEL 6093D Dec -25-'86 EN 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 'iM DESCRIPTION 'iM $fD DESCRIPTION 1 1 1 1 4 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 10 11 12 13 .
I MAKITA LIMED ONE YEAR WARRANTY Warranty Policy t Every Makita tool is thoroughly inspected and tested before leaving the factory. It is warranted to be free of defects from workmanship and materials for the period of ONE YEAR from the date of original purchase.
デバイスMakita 6093Dの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Makita 6093Dをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはMakita 6093Dの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Makita 6093Dの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Makita 6093Dで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Makita 6093Dを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はMakita 6093Dの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Makita 6093Dに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちMakita 6093Dデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。