MartinLoganメーカーPASSAGE TMの使用説明書/サービス説明書
ページ先へ移動 of 16
™ P A S S A G E ™ user ’s manual M A R T I N L O G A N the loudspeaker technology company ®.
Contents and Introduction . . . . . . . . . . . . . . . . . . . 2 Contents Introduction Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Placement Horizontal Installation Installing the P assage Installing an IR Repeater . . .
T o ac hieve maximum perform ance, it is rec ommended that the P assage n ot be inst alled near a roo m cor ner o r dire ctly behin d furnit ure. Whe n used as a fr ont left /right c hannel, it is recommended that the listening position be no closer to the wa ll then th e dist ance betwee n the spea kers.
Required tools (included): 4mm Allen bit (2) P ush pins Required tools (not included): Stud finder Sharp pencil or pen Level Dry wall knife/saw Wire strippers Electric drill (with clutch) T ape measure Depth required behind wall surface: 3 3 / 16 " (8.
1 Using a stud finder , locate the final speaker position between studs. WAR NING! A bs o l ut e l y n o p a rt of th e t em p la te s ho ul d ov e rl ap a s t ud . 2 Insert top push pin (provided). Level template. Insert bottom pushpin (provided). Recheck level.
6 Installation Fi gu re 7. I nst all at io n st ep 5 . Fi gu re 8. I nst all at io n st ep 6 . 5 If t he t wee ter is a bov e o r be low ear lev el, pos iti on the marked woofer closest to ear level (see sticker on the back of speaker). 6 Co n n e c t sp e a k e r ca b l e .
Installation 7 Fi gu re 10 . Ins tal la ti on s te p 8. 7 Place spe aker in h ole. 8 Use a 4mm Allen bit (provided) and an electric drill to lock all 8 mounting locks in place. Use a low clutch setting on the drill. Fi gu re 9. I nst all at io n st ep 7 .
8 Installation Fi gu re 11 . Ins tal la ti on s te p 9. 9 Aim the tweeter toward the primary listening position by gently pushing the edge of the tweeter globe (which is capable of 20° tilt in all directions).
WARNING! These instructions are written based on commonly available IR repeaters that mount in a 1 / 2 " diameter hole. Before beginning this installation, please refer to the instructions that came with your IR repeater to verify this hole size.
10 Removing the End Caps for Painting Required tools (not inc luded): Philips head scrwedriver 1 P repare a flat surface with a cushion and/or blanket to pro tect the P assa ge. P lace the P assa ge dr iver side down. WARNING! Be careful to put no weight on the tweeter globe.
A TF Operation The MartinLogan A TF transducer (based on RADIA planar technology) consists of a micro-thin, low -mass Kaladex diaphragm with an ultra-light, etched conductive alumi- num surface suspended between two high fi eld str en gt h neo dymiu m super magn et arra ys (s ee figu re 17).
12 Frequently Asked Questions and Troubleshooting F REQUENTL Y A SKED Q UESTIONS AND T ROUBLESHOOTING How do I clean my speakers? Just use a dust free cloth or a soft brush to remove the du st from your speakers. W e recommend a specialty cloth (available at the Xtatic shop at www .
System Frequency R esponse 45–20,000 Hz ± 3 dB Sensitivity 90 dB/2.83 volts/meter (mounted on wall) Impedance 6 ohms Crossover Frequency 2200 Hz Components Air core coils, metal film and low dissipation electrolytic capacitors W oofer T ype T wo 6.
AC. Abbreviation for alternating current. Active crossover . Uses active devices (transistors, ICs, tubes) and some form of power supply to operate. Amplitude. The extreme range of a signal. Usually mea- sured from the average to the extreme. Arc. T h e v i s i b l e s p a r k s g e n e r a t e d b y a n e l e c t r i c a l d i s - charge.
Glossary of Audio Terms 15 Inductance. The property of an electrical circuit by which a varying current in it produces a varying magnetic field that introduces voltages in the same circuit or in a nearby circuit. It is measured in henrys. Inductor . A device designed primarily to introduce induc- tance into an electrical circuit.
2101 Delaware Street, Lawrence, K ansas 66046, USA tel 785.749.0133 fax 785.749.5320 www .martinlogan.com M A R T I N L O G A N the loudspeaker technology company ©2004 MartinLogan.
デバイスMartinLogan PASSAGE TMの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
MartinLogan PASSAGE TMをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはMartinLogan PASSAGE TMの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。MartinLogan PASSAGE TMの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。MartinLogan PASSAGE TMで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
MartinLogan PASSAGE TMを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はMartinLogan PASSAGE TMの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、MartinLogan PASSAGE TMに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちMartinLogan PASSAGE TMデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。