Master LockメーカーMK-470の使用説明書/サービス説明書
ページ先へ移動 of 12
Manual Part No. 156934 Revision 10/01 Model MK-470 T ile Saw Owner ’s Manual Parts List & Operating Instructions serial number R For your warranty to be effective, complete the warranty card (include the serial number) and mail it in as soon as possible.
T a b l e o f C o n t e n t s Foryour safety, read all instructions! These safety precautions should be followed at all times. Failure to follow these safety precautions could result in injury to yourself and others. Safety is a combination of operator common sense and alertness at all times when the saw is being used.
Safety labels are located according to the drawing below. The labels contain important safety information. Please read them carefully. These labels are considered a permanent part of your saw. If a label comes off or becomes hard to read, contact MK Diamond or your dealer for replacement.
3 Carefully open carton. Remove the accessory pack. Lift the saw out of the carton by the pan, and place onto a level work surface. Open the accessory pack, and check each item with the contents list and illustration below, making certain that all items are accounted for and in good condition before discarding any packing material.
The MK-470 tile saw is wired for 120V, single phase operation, and draws 5.3 amps at 120V. This is not a large load, however if the machine is operated on any circuit that is already close to its capacity, the circuit breaker may be tripped. If this occurs, eliminate other loads from the circuit.
S a w i n g O pe r a t i o n s G e n e r a l C u t t i n g G u i d e l i n e s • A diamo nd bl ade does n ot cut, it grinds. Do not force the tile into the blade, nor feed it to quickly . • Di am o n d b lade s a re n o t all al ike. M a tch the M K bl a d e to th e pro duct to be cut.
Do not attempt to cut pieces too small to hold by hand outside the blade guard. Avoid awkward hand positions where a sudden slip could cause a hand or fingers to come in contact with the blade. When cutting any material, make sure it is fully supported.
Optiona l Ac cesso ries wate r flow problems Check that the water pump vibrates when the motor is on. Reprime pump: Take water hose off blade guard, r emove air bubbles, fully submerse pump outlet in water, turn motor on. Plug the water pump into an electrical outlet, fully submerse pump in water and check it’s operation.
t i l e s a w B2 X4 B3 B4 H4 G4 G2 G3 G1 H5 X3 A7 H6 H5 A3 B1 B5 B4 K7 K6 X2 X2 X2 K5 K8 X2 K3 X2 K4 K1 X2 K2 X2 E3 E4 E2 X2 J2 J1 J3 L3 L2 L4 H3 H1 L1 E 1 F 1 MK-470 Exploded View N3 N4 N1 E2 E3 E4 D.
9 MK-470 Parts List Model MK-470 Tile Saw 120v/7.4a, Part # 155779 Item Description Qt y Part # A1 Wrench, Blade Nut, 15/16 Boxed End 1 134684 A2 Wrench, Blade Shaft, 11/16 Open End 1 153450 A3 Blade,.
10 K5 Wheel, Roller 2 151799 K6 Screw, 1/4-20 X 1 1/4 Hex Head Cap 2 157145 K7 Washer, 1/4 SAE Flat 2 151915 K8 Nut, 1/4-20 Hex 2 151893 L Assembly, Splash Curtain 1 155901-MK L1 Curtain, Splash 1 134.
1315 Storm Parkway. Torrance, CA 90509-2803 1 (800) 421-5830 F AX 1 (310) 539-5158 (310) 539-5221 www.mkdiamond.com MK Diamond Products, Inc. R HOW TO ORDER PARTS Please have the following information.
デバイスMaster Lock MK-470の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Master Lock MK-470をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはMaster Lock MK-470の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Master Lock MK-470の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Master Lock MK-470で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Master Lock MK-470を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はMaster Lock MK-470の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Master Lock MK-470に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちMaster Lock MK-470デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
