MaxtorメーカーSTM3320614ASの使用説明書/サービス説明書
ページ先へ移動 of 48
Product Manual DiamondMax 22 Serial A T A 100544218 Rev . A November 2008 STM31000334AS STM3320614AS STM3160813AS.
Revision history Copyright © 2008 Seagate T echnology LLC. All right s reserved. Printed in U.S.A. Publication number: 1005 44218, Rev . A November 2008 Seagate, Seagate T echnology and the W ave logo ar e registere d trademarks of Seagate T echnology LLC in the United S tates and/or other countries.
DiamondMax 22 Serial ATA Product Manual, Re v. A i Contents 1.0 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 1.1 About the Serial ATA interface . .
ii DiamondMax 2 2 Serial ATA Product M anual, Rev. A.
DiamondMax 22 Serial ATA Product Manual, Re v. A iii List of Figures Figure 1. Typical 5V startup and operation current profile . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12 Figure 2. Typical 12V startup and operation current profile .
.
DiamondMax 22 Serial ATA Product Manual, Re v. A 1 1.0 Introduction This manual describes the functiona l, mechanical an d interface specifications for the following Seagate DiamondMax ® 22 Serial A T A model drives: These drives provide the following key fea tures: • 7,200 RPM spindl e speed.
2 DiamondMax 22 Serial ATA Produc t Manual, Rev. A 1.1 About the Serial A T A interface The Serial A T A interface pr ovides several advant ages over the traditional (p arallel) A T A interface. The primary advantages include : • Easy installation and configuration with true plug-and-pla y connectivity .
DiamondMax 22 Serial ATA Product Manual, Re v. A 3 2.0 Drive specifications Unless otherwise noted, all specific ations are measur ed under ambient conditions, at 25°C, and nominal power .
4 DiamondMax 22 Serial ATA Produc t Manual, Rev. A T able 1: Drive specifications summary for 1000 Gbyte mo dels Drive specification STM31000334AS Formatted capacity (512 bytes/sector)* 1000 Gbytes Gu.
DiamondMax 22 Serial ATA Product Manual, Re v. A 5 * One Gbyte equals one billion bytes when referring to h ard driv e capacity. Accessible capacity may vary depending on operating environment and formatting. * *During periods of drive idle, some offli ne activity may occur according to the S.
6 DiamondMax 22 Serial ATA Produc t Manual, Rev. A T able 2: Drive specifications summary for 320 and 160 G byte models Drive specification STM3320614AS STM3160813AS Formatted capacity (512 bytes/sect.
DiamondMax 22 Serial ATA Product Manual, Re v. A 7 * One Gbyte equals one billion bytes when referring to h ard driv e capacity. Accessible capacity may vary depending on operating environment and formatting. * *During periods of drive idle, some offli ne activity may occur according to the S.
8 DiamondMax 22 Serial ATA Produc t Manual, Rev. A 2.1 Formatted cap acity *One Gbyte equals one billion bytes when referri ng to hard drive capacity. Accessible c apa city may vary depending on o perating environment and formatting.
DiamondMax 22 Serial ATA Product Manual, Re v. A 9 2.4 Physical characteristics 2.5 Seek time Seek measurement s are t aken with nominal p ower at 25°C ambient temperatur e.
10 DiamondMax 2 2 Serial ATA Product M anual, Rev. A 2.6 St art/stop times 2.7 Power specifications The drive receives DC power (+ 5V or +12V) thro ugh a na tive SA T A power connector . See Figure 4 on page 22. 2.7.1 Power co nsumption Power requirement s for the drives are listed in the table on page 9.
DiamondMax 22 Serial ATA Product Manual, Re v. A 11 T able 3: DC power require ment s * During periods of drive idle, some offline activity may occur according to the S.M.A.R. T. specification, which may increase ac oustic and power to operational levels .
12 DiamondMax 2 2 Serial ATA Product M anual, Rev. A 2.7.1.1 T ypical cu rrent profiles Figure 1. T ypical 5V st artup and operation curren t profile Figure 2.
DiamondMax 22 Serial ATA Product Manual, Re v. A 13 2.7.2 C onducted noise Input noise ripp le is measured at the host system powe r supply across an equivalent 80-ohm resistive load o n the +12 volt line or an equival ent 15-ohm resistive load on the +5 volt line.
14 DiamondMax 2 2 Serial ATA Product M anual, Rev. A 2.8 Environment al specifications 2.8.1 Ambient tempe rature Ambient temperatur e is defined as the temperatur e of the en vironmen t immediatel y surr ounding the drive. Actual drive c ase temperature should not exce ed 69°C (156°F) within the operatin g ambient conditio ns.
DiamondMax 22 Serial ATA Product Manual, Re v. A 15 2.8.5 Sho ck All shock specifications assu me that the drive is mounted secu rely with the input sh ock applied at the drive mounting screws.
16 DiamondMax 2 2 Serial ATA Product M anual, Rev. A 2.9 Acoustics Drive acoustics are measured as ov erall A-weighted ac oustic sound power levels (no pure tones). All mea- surements ar e consistent with ISO document 7779. Soun d power measurem en ts a re ta ken under essentially free-field conditions over a reflecting plane.
DiamondMax 22 Serial ATA Product Manual, Re v. A 17 2.1 1 Reliability 2.1 1.1 Annualized Failure Rate ( AFR) and Mean T ime Between Failure s (MTBF) The product shall achi eve an Annualized Failure Rate (AFR) of 0.34% (MTBF of 0.7 million hours) when oper- ated in an envir onment of ambien t air temperatures of 25 ° C.
18 DiamondMax 2 2 Serial ATA Product M anual, Rev. A Korean RRL If these dr ives have the Ko rea Ministry of Informat ion and Communication (MIC ) logo, they comply with paragraph 1 of Article 1 1 of .
DiamondMax 22 Serial ATA Product Manual, Re v. A 19 2.13 Environment al protection Seagate des igns its products to meet environme nt al pr otection requirements worl dwide, including regula tions restricting certain chemical substances.
20 DiamondMax 2 2 Serial ATA Product M anual, Rev. A.
DiamondMax 22 Serial ATA Product Manual, Re v. A 21 3.0 Configuring and mounting the drive This section contains the specif ications an d instructions for configuring and mounting the drive.
22 DiamondMax 2 2 Serial ATA Product M anual, Rev. A 3.2 Configuring the drive Each drive on the Seri al A T A interface connect s point-to-point with the Serial A T A host ada pter . There is no master/slave rela tionship because each drive is consider ed a master in a point-to -point relationship.
DiamondMax 22 Serial ATA Product Manual, Re v. A 23 3.4 Drive mounting Y ou can mount the drive in any orient ation using four screws in the side-mounting holes or four screws in the bottom-mo unting holes. See Fi gure 5 for drive mo unting dimension s.
24 DiamondMax 2 2 Serial ATA Product M anual, Rev. A Figure 6. Mounting dimensions (320 and 160 GB models).
DiamondMax 22 Serial ATA Product Manual, Re v. A 25 4.0 Serial A T A (SA T A) interface These drives use the industry-s tandar d Serial A T A interfac e th at support s FIS dat a transfers. It support s A T A programmed input/o utput (PIO) modes 0–4; mult iword DMA modes 0–2, and Ultr a DMA modes 0–6.
26 DiamondMax 2 2 Serial ATA Product M anual, Rev. A 4.2 Serial A T A device p lug connector pin definitions Table 7 summarizes the sig nals on the Se rial ATA interface and power co nnectors. . Notes: 1. All pins are in a single row , with a 1.27 mm (0.
DiamondMax 22 Serial ATA Product Manual, Re v. A 27 4.3 Supported A T A commands The following t able list s Serial A T A standa rd commands that the drive support s. For a deta iled description of the A T A commands, re fer to the Se rial A T A Internatio nal Organization: Seria l A T A Revision 2.
28 DiamondMax 2 2 Serial ATA Product M anual, Rev. A Security Erase Unit F4 H Security Freeze F5 H Security Set Password F1 H Security Unlock F2 H Seek 70 H Set Features EF H Set Max Address F9 H Note: Individual Set Max Address commands are identifie d by the value placed in the Set Max Features regis - ter as defined to the right.
DiamondMax 22 Serial ATA Product Manual, Re v. A 29 4.3.1 Identify Dev ice command The Identify Device command (command code EC H ) transfers information about the drive to the host following power up. The da ta is organized as a single 512-b yte block of data, whose conten ts are shown in T able 8 on page 27.
30 DiamondMax 2 2 Serial ATA Product M anual, Rev. A 60–61 T otal number of user-addressable LBA sectors availabl e (see Section 2.1 for related information) *Note: The maximum value all owed in this field is: 0FFFFFFFh (268,435,455 sectors, 137 Gbytes).
DiamondMax 22 Serial ATA Product Manual, Re v. A 31 Note. Advance d Power Management (APM) and Automatic Acou stic Management (AAM) feat u res are not supported Note. See the bit descriptio ns below for words 63 , 84, and 88 of the Identify Drive data.
32 DiamondMax 2 2 Serial ATA Product M anual, Rev. A Bit Wor d 88 0 Ultra DMA mode 0 is supported. 1 Ultra DMA mode 1 is supported. 2 Ultra DMA mode 2 is supported. 3 Ultra DMA mode 3 is supported. 4 Ultra DMA mode 4 is supported. 5 Ultra DMA mode 5 is supported.
DiamondMax 22 Serial ATA Product Manual, Re v. A 33 4.3.2 Set Featu res command This command controls the implement ation of various fe at ures that th e drive support s. When the drive receives this command, it sets BSY , checks the contents of the Featur es register , clears BSY and gen erates an inte r- rupt.
34 DiamondMax 2 2 Serial ATA Product M anual, Rev. A 4.3.3 S.M.A .R.T . commands S.M.A.R.T . provides near-term failure prediction fo r disc drives. When S.M.A.R.T . is enabled, the d rive moni- tors predetermined drive attributes that are suscep tible to degradation over time.
DiamondMax 22 Serial ATA Product Manual, Re v. A 35 5.0 Seagate T echnology support services Online services Internet For information regardin g Seagate product s and services, visit www .seagate.com . Worldwide support is available 24 hours daily by ema il for your questions.
36 DiamondMax 2 2 Serial ATA Product M anual, Rev. A Customer Service Operations W arranty Servi ce Seagate of fers worldwide customer support for Seagate product s. Seagate distributor s, OEMs and othe r direct customers should contact their Seagate Customer Ser v ice Operat ions (CSO) represen tative for warranty- related issues.
DiamondMax 22 Serial ATA Product Manual, Re v. A 37 Index A ACA 18 acceleration 15 acoustics 16 Active 13 Active m ode 13 actuator arm 10 AFR 17 Agency certification 17 altitude 14 Ambient temperature.
38 DiamondMax 2 2 Serial ATA Product M anual, Rev. A I I/O data-transfer rate 8 I/O duty cycle 17 Identify Device 27 Identify Device command 29 Idle 13 , 27 Idle Immediate 27 Idle mode 10 , 13 IEC950 .
DiamondMax 22 Serial ATA Product Manual, Re v. A 39 RMS read/write current 13 RoHS 19 RRL 18 S S.M.A.R.T. Disable Operations 28 S.M.A.R.T. Enable Operations 28 S.M.A.R.T. Enable/Disable Autosave 28 S.M.A.R.T. Execute Offline 28 S.M.A.R.T. implementation 27 S.
40 DiamondMax 2 2 Serial ATA Product M anual, Rev. A.
.
Seagate T echnology LLC 920 Disc Drive, Scotts V a lley , California 95066 -4544, USA Publication Number: 1005442 18, Rev . A, Printed in U.S.A..
デバイスMaxtor STM3320614ASの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Maxtor STM3320614ASをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはMaxtor STM3320614ASの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Maxtor STM3320614ASの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Maxtor STM3320614ASで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Maxtor STM3320614ASを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はMaxtor STM3320614ASの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Maxtor STM3320614ASに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちMaxtor STM3320614ASデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
