McCullochメーカーMB3201の使用説明書/サービス説明書
ページ先へ移動 of 24
® McCulloch Corporation P .O. Box 31567 • T ucson, AZ 85751-1567 U.S.A. McCulloch Corporation P. O . Box 31567 Tu c s on, AZ 85751-1567 USA McCulloch Canada 525 Southgate Drive - Unit #2 Guelph, ON N1G 3W6 Canada MEXICO Imported by / Importe par: Comercializadora Marvel S.
E N G L I S H PLEASE READ The W ARRANTY SYMBOL indicates that unless instructions or procedures are followed any damage caused will void the warranty and repairs will be at owner ’s expense. A CAUTION may also accompany the W ARRANTY SYMBOL . Service other than user maintenance should be performed by a McCulloch Authorized Service Center .
E N G L I S H PLEASE READ The W ARRANTY SYMBOL indicates that unless instructions or procedures are followed any damage caused will void the warranty and repairs will be at owner ’s expense. A CAUTION may also accompany the W ARRANTY SYMBOL . Service other than user maintenance should be performed by a McCulloch Authorized Service Center .
3 4 E N G L I S H * 3-1. WHA T T O DO READ YOUR USER MANUAL AND ALL SUPPLEMENTS (IF ANY ENCLOSED) THOROUGHL Y BEFORE OPER- A TING YOUR UNIT . 1. WEAR CLOSE FITTING, T OUGH WORK CLOTHING that will prov.
3 4 E N G L I S H * 3-1. WHA T T O DO READ YOUR USER MANUAL AND ALL SUPPLEMENTS (IF ANY ENCLOSED) THOROUGHL Y BEFORE OPER- A TING YOUR UNIT . 1. WEAR CLOSE FITTING, T OUGH WORK CLOTHING that will prov.
6 E N G L I S H 5. DUE TO THE DANGER of exhaust fumes, never operate blower in a confined or poorly ventilated area. 6. NEVER POINT BLOWER in the direction of people, animals, buildings, automobiles, or windows, etc. 7. DO NOT operate unit without inlet cover installed to prevent contact with impeller .
6 E N G L I S H 5. DUE TO THE DANGER of exhaust fumes, never operate blower in a confined or poorly ventilated area. 6. NEVER POINT BLOWER in the direction of people, animals, buildings, automobiles, or windows, etc. 7. DO NOT operate unit without inlet cover installed to prevent contact with impeller.
8 E N G L I S H 4-1. BLOWER A TT ACHMENT ASSEMBL Y INSTRUCTIONS 1. Twist blower nozzle (A) clockwise into the straight blower tube (B) until tight (Figure 4-1A). 2. Insert the straight blower tube (B) into the blower housing (C). Align tabs (D) on tube with grooves (E) in the housing (Figure 4-1B).
8 E N G L I S H 4-1. BLOWER A TT ACHMENT ASSEMBL Y INSTRUCTIONS 1. Twist blower nozzle (A) clockwise into the straight blower tube (B) until tight (Figure 4-1A). 2. Insert the straight blower tube (B) into the blower housing (C). Align tabs (D) on tube with grooves (E) in the housing (Figure 4-1B).
10 9 E N G L I S H 3. Hold inlet cover open. Insert tube aligning tabs (L) and notches (M). Turn clockwise to lock tube into position (Figure 4-3F) . 4. Install cover screw (K) through tube tab and into housing. Tighten screw (Figure 4-3G). 4-4. SIDE HANDLE (MB3201 Blower / Vac Model) 1.
10 9 E N G L I S H 3. Hold inlet cover open. Insert tube aligning tabs (L) and notches (M). Turn clockwise to lock tube into position (Figure 4-3F) . 4. Install cover screw (K) through tube tab and into housing. Tighten screw (Figure 4-3G). 4-4. SIDE HANDLE (MB3201 Blower / Vac Model) 1.
12 11 E N G L I S H 5-4. FUEL MIXING T ABLE 5-5. RECOMMENDED FUELS Some conventional gasolines are being blended with oxygenates such as alcohol or an ether compound to meet clean air standards. Y our McCulloch engine is designed to operate satisfactorily on any gasoline intended for automotive use including oxygenated gasolines.
12 11 E N G L I S H 5-4. FUEL MIXING T ABLE 5-5. RECOMMENDED FUELS Some conventional gasolines are being blended with oxygenates such as alcohol or an ether compound to meet clean air standards. Y our McCulloch engine is designed to operate satisfactorily on any gasoline intended for automotive use including oxygenated gasolines.
14 13 E N G L I S H 7. Once engine starts leave the choke in the ST ART “ ” position for 10 seconds, then move the choke to RUN “ ” position (Figure 6-1F). Squeeze trigger to release throttle lock. 8. If engine fails to start, repeat steps 1 through 7.
14 13 E N G L I S H 7. Once engine starts leave the choke in the ST ART “ ” position for 10 seconds, then move the choke to RUN “ ” position (Figure 6-1F). Squeeze trigger to release throttle lock. 8. If engine fails to start, repeat steps 1 through 7.
16 E N G L I S H 7-2. V ACUUM OPERA TIONS (MB3201 Blower / V ac Models only) Blower Units If your unit is vac-capable and was not equipped with a vacuum kit, a vacuum attach - ment accessory kit is available for purchase at your nearest McCulloch Authorized Service Center .
16 E N G L I S H 7-2. V ACUUM OPERA TIONS (MB3201 Blower / V ac Models only) Blower Units If your unit is vac-capable and was not equipped with a vacuum kit, a vacuum attach - ment accessory kit is available for purchase at your nearest McCulloch Authorized Service Center .
18 17 E N G 8-1. AIR FIL TER CAUTION NEVER operate blower without the air filter or dust and dirt will be sucked into the engine and damage it. The air filter must be kept clean.
18 17 E N G 8-1. AIR FIL TER CAUTION NEVER operate blower without the air filter or dust and dirt will be sucked into the engine and damage it. The air filter must be kept clean.
20 19 E N G L I S H 8-6. V ACUUM BAG CLEANING A dirty bag will obstruct airflow , thereby reducing vacuum efficiency . To Clean Bag: 1. Detach vacuum bag from unit. 2. Open zipper and remove contents. 3. Turn bag INSIDE OUT and shake vigorously . This procedure should be performed on a regular basis.
20 19 E N G L I S H 8-6. V ACUUM BAG CLEANING A dirty bag will obstruct airflow , thereby reducing vacuum efficiency . To Clean Bag: 1. Detach vacuum bag from unit. 2. Open zipper and remove contents. 3. Turn bag INSIDE OUT and shake vigorously . This procedure should be performed on a regular basis.
22 21 E N G 9. Store unit in a cool, dry place away from any source of ignition such as an oil burner , water heater , etc. 8-8. REMOVING A UNIT FROM ST ORAGE 1. Remove spark plug. 2. Pull starter rope briskly to clear excess oil from combustion chamber.
22 21 E N G 9. Store unit in a cool, dry place away from any source of ignition such as an oil burner , water heater , etc. 8-8. REMOVING A UNIT FROM ST ORAGE 1. Remove spark plug. 2. Pull starter rope briskly to clear excess oil from combustion chamber.
® McCulloch Corporation P .O. Box 31567 • T ucson, AZ 85751-1567 U.S.A. McCulloch Corporation P. O . Box 31567 Tu c s on, AZ 85751-1567 USA McCulloch Canada 525 Southgate Drive - Unit #2 Guelph, ON N1G 3W6 Canada MEXICO Imported by / Importe par: Comercializadora Marvel S.
デバイスMcCulloch MB3201の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
McCulloch MB3201をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはMcCulloch MB3201の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。McCulloch MB3201の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。McCulloch MB3201で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
McCulloch MB3201を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はMcCulloch MB3201の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、McCulloch MB3201に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちMcCulloch MB3201デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。