MeadeメーカーTE653ELW-Mの使用説明書/サービス説明書
ページ先へ移動 of 24
TE653ELW-M Complete Weather Forecaster with Indoor/ Outdoor Temperature and Humidity USER MANUAL MADE IN CHINA.
INTRODUCTION Thank you for selecting a Meade Instruments W eather Forecaster . This device combines precise time keeping, monitoring and displaying of current temperature data from up to three remote locations (additional sensors are required).
INST ALLA TION Communications between the main unit (receiver) and the remote sensor (transmitter) is wireless. This allows you to greater flexibility in choosing the location of remote sensor . The remote transmits data up to 164 feet (50 meters) over an open, unobstructed area.
4 REMOTE SENSOR FEATURES • Remote temperature transmission to the main unit via 433 MHz signal • Case can be wall mounted using built-in hanger • 164 feet transmission range without interference.
PLACEMENT • The remote sensor should be placed under eaves or a similar location with free air circulation, sheltered from direct sunlight and extreme weather . • Ideally , place the remote sensor over soil, rather than asphalt, which would cause false readings.
FRONT REAR 6 MADE IN CHINA A H G F E B L I D J K C M N O.
A. WEA THER FORECAST/ PRESSURE window B. TEMPERA TURE/ HUMIDITY window C. CLOCK window D. DOWN button • Select the next available mode • Press and hold for 2 seconds to search for wireless signal from remote sensor .
BA TTERY INST ALLA TION • Remove the battery door located at the back of the main unit. • Insert two (2) AA batteries and replace the battery compartment door . PLACEMENT • Make sure that the main unit is locating within the operating range of all remote sensors.
PRESSURE OPERA TION The pressure window displays: current barometric pressure, sea level pressure, and weather forecast. The information contains a number of historical statistics: pressure/ temperature/ humidity history bar -chart for the past 24 hours.
New Moon W aning Crescent First Quarter W axing Gibbous Full Moon W aning Gibbous Last Quarter W aning Crescent CHANGING PRESSURE AND ALTITUDE UNITS • Press MODE as needed, until “LOCAL” pressure is displayed. • Press and hold HISTOR Y , until the pressure unit is flashing.
Icon Status Searching for the signals from the remote sensor Corresponding remote sensor signal received successfully No signals received for over 1 hour REMOTE SENSORS ST A TUS The wave icon above th.
VIEWING MAX/MIN AND MINIMUM READINNGS Press the MEMORY button recalling: • Current temperature and humidity • Minimum temperature and humidity • Maximum temperature and humidity at the remote location.
ICON Atomic Time Reception Strength Undefined data (Flashing) No Reception for the past 24 hours W eak signal, but can be decoded Strong signal • The atomic clock receiver is programmed that it will search for the atomic time signal daily for 0:00, 3:00, 6:00, and 12:00 am.
CLOCK ALARMS There are two time alarms – Weekday alarm ( W ) and Single day alarm ( S ) - and one Ice Warning Alarm ( PRE-AL ). • If Weekday (W) alarm is activated, it will sound at the set time a.
Issue Main unit Radio Controlled T ime signal is not received Cannot locate remote sensor Cannot change the channel Data does not match data on the main unit Place unit by the window and keep it there.
BA TTERY INST ALLA TION • Remove the battery door located at the back of the main unit. • Insert two (2) AA batteries and replace the battery compartment door . PLACEMENT • Make sure that the main unit is locating within the operating range of all remote sensors.
PRESSURE OPERA TION The pressure window displays: current barometric pressure, sea level pressure, and weather forecast. The information contains a number of historical statistics: pressure/ temperature/ humidity history bar -chart for the past 24 hours.
New Moon W aning Crescent First Quarter W axing Gibbous Full Moon W aning Gibbous Last Quarter W aning Crescent CHANGING PRESSURE AND ALTITUDE UNITS • Press MODE as needed, until “LOCAL” pressure is displayed. • Press and hold HISTOR Y , until the pressure unit is flashing.
Icon Status Searching for the signals from the remote sensor Corresponding remote sensor signal received successfully No signals received for over 1 hour REMOTE SENSORS ST A TUS The wave icon above th.
VIEWING MAX/MIN AND MINIMUM READINNGS Press the MEMORY button recalling: • Current temperature and humidity • Minimum temperature and humidity • Maximum temperature and humidity at the remote location.
ICON Atomic Time Reception Strength Undefined data (Flashing) No Reception for the past 24 hours W eak signal, but can be decoded Strong signal • The atomic clock receiver is programmed that it will search for the atomic time signal daily for 0:00, 3:00, 6:00, and 12:00 am.
CLOCK ALARMS There are two time alarms – Weekday alarm ( W ) and Single day alarm ( S ) - and one Ice Warning Alarm ( PRE-AL ). • If Weekday (W) alarm is activated, it will sound at the set time a.
Issue Main unit Radio Controlled T ime signal is not received Cannot locate remote sensor Cannot change the channel Data does not match data on the main unit Place unit by the window and keep it there.
MADE IN CHINA Meade Instruments Corp. 27 Hubble Irvine, CA 92618 U.S.A. ©201 1 Meade Instruments Corp. All Rights Reserved. All user manual contents and information are subject to change.
デバイスMeade TE653ELW-Mの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Meade TE653ELW-Mをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはMeade TE653ELW-Mの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Meade TE653ELW-Mの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Meade TE653ELW-Mで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Meade TE653ELW-Mを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はMeade TE653ELW-Mの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Meade TE653ELW-Mに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちMeade TE653ELW-Mデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
