Mecoメーカー7110.7.641の使用説明書/サービス説明書
ページ先へ移動 of 23
Aussie ® by Meco ® LP Gas Grill Assembly and Use Manual Joey TM For Customer Service, call 1-800-251-7558 or visit our web site at www .meco.net FOR OUTDOOR HOUSEHOLD USE ONL Y . NOT FOR COMMERCIAL USE. • Failure to follow these instructions could result in fire or explosion which could cause death, serious personal injury , or property damage.
2 I. Assembly Instructions.......................................................2 Parts Illustrations................................................................3 S tep 1) Cart Assembly ........................................................5 S tep 2) Assemble Axle, Wheels, & Wheel Covers.
3 P ARTS ILLUSTRA TIONS If you need replacement part s, refer to the Parts Illustrations and the Parts List to find the exact p arts you need. If you have any questions which require help, contact Customer Service and be sure to mention the model number of your grill.
(35) Flame Diffuser (34) Cooking Grid (37) Fabric Panel (39) LP Cylinder Heat Shield (36) Main Burner 42) Main Burner Electrode (40) Control Panel w/Manifold and Regulator (38) W arming Rack 4 (33) Ho.
5 STEP 1) Cart Assembly: Att ach the Legs to the Bottom Shelf with M5 x 40 Bolt s threaded into the Bottom Shelf holes. Position legs with the holes exactly as indicated . (4) LEFT FRONT WHEEL LEG T o reduce the risk of a cut injury: · Wear protective gloves when handling p art s that have sharp edges.
STEP 2) Assemble Axle, Wheels & Wheel Covers: 6 (10) WHEEL 2 PC (12) WHEEL COVER 2 PC Push Axle through center hole in Wheel and through lower hole in each leg. (FIG . 2A) Insert Axle pin through small hole in end of Axle until it snap s over it. (FIG .
Step 4) Inst all Drip Cup: Insert Drip Cup into Drip Cup Holder ring (inst alled in bottom of Grill Body) until the cup flange is flush with the ring (17) DRIP CUP Step 3) Assemble Hood/Bowl to Cart: (15) BOL T , M6X45 4 PC (16) M6 LOCKNUT 4 PC FIG . 3A FIG .
8 Step 5) Assemble Sidebraces: · Att ach Right and Left Sidebraces (19 & 20) to legs with ST4.0 x 10 Screws. (FIG . 5A) Secure Bottom Heat Shield to Lef t Sidebrace with M4x10 Bolts and M4 W ingnuts. (FIG . 5B) Allow Heat Shield Edge to overlap Sidebrace edge.
9 (27) BOL T , M6X15 8 PC (27) SCREW , M6X15 FIG . 6A FIG . 6B (27) BOL T , M6X15 (26) LEFT SIDE T ABLE (25) RIGHT SIDE T ABLE Step 6) Assemble Side T ables: Align bracket holes of Lef t and Right Side T ables with holes in Bowl Leg Bracket s. Attach Side T ables with M6 x 15 Bolts underneath.
Step 10) Inst all Cooking Grid: (Note W arming Rack already inst alled.) Lay Cooking Grid onto the Bowl ridges over the Flame Diffuser and Main Burner . (FIG . 10) 10 Step 8) Attach Front Panel: Remove the M6 nut used to att ach the upper and lower leg sections.
11 T o reduce the risk of serious bodily injury or death: · Use only prop ane gas in this LP gas grill. · Do not attempt to convert an LP unit to natural gas. · Any use or alteration of this unit not intended could be unsafe and will void your warranty .
Cylinder Ret ainer Clip Cylinder Carry Handle T o avoid pinching in next step, keep fingers and hands near corners of Cylinder Ret ainer Clip when swinging Clip over cylinder . 6) Swing the Cylinder Ret ainer Clip over round shoulder of the LP cylinder .
13 T o reduce the risk of serious bodily injury or death: · This out door cooking appliance shall be used only out doors and shall not be used in a building, garage, or any other enclosed area. Locate out door cooking appliance in an area with good ventilation on a level st able surface clear of combustible and flammable material.
14 1. Open the Hood. 2. Import ant: Make sure all control knobs are turned “Off”. (FIG . 13A) 3. T urn the LP Gas Cylinder valve open counter clockwise until it stop s. (FIG . 13B) 4. Push the lef t control knob in and turn counter clockwise to the High flame position.
15 MANUAL LIGHTING THE GRILL 1. Open the Hood. 2. Import ant: Make sure control knobs are turned “Off”. (See FIG . 13A) 3. T urn the LP Gas Cylinder valve open counter clockwise until it stop s. (See FIG . 13B) 4. Insert a lit match through match-lighting hole underneath the grill bowl on the right side.
16 Closing the Hood forms an ‘oven’ and traps a large amount of heat for roasting whole meats, chickens, etc. Therefore, it is IMPORT ANT that the burner is turned to the “Low “ position to prevent burning of the food. T o contain juices and fat, place the food to bake or roast in a metal baking tray .
17 1) Remove Drip Cup, Cooking Grid, and Flame Diffuser . 2) Drip Cup- W ash the Drip Cup with soap and water . 3) Grill Body and Cart -Do not mist ake the accumulation of grease and smoke residue for peeling or flaking paint. Remove excess grease and/or fat with a soft plastic or wooden scraper .
FIG . 15B Wingnut s Heat Shield edge over Crossbrace edge Screws Heat Shield V alve nozzles must fit inside Burner venturi tubes . Burner Screw FIG . 15C 5) Use a pipe cleaner to clear insect nests from the inlet hole of main burner (FIG . 15D ). Open up the main burner holes with a small nail or wire.
19 Problem Possible Cause Solution Gas leaking from cracked/cut/burned hose. Damaged hose. Mechanical failure due to rust or mishandling. Failure of valve from mishan- dling or mechanical malfunc- tion. Fire in or around venturi tube section of the burner .
20 Natural Gas supply pressure is low TROUBLESHOOTING (Cont’d) Problem Flames blow out Flare up Persistent grease fire Unable to fill LP t ank Possible Cause High or gusting winds Gas in LP cylinder.
21 TROUBLESHOOTING (Cont’d) Although this sound may be alarming, this is NOT dangerous as long as it is not accompanied by the smell of gas. Simply adjust the burner settings and usually the sound will subside. If the humming sound persists, a change in atmospheric conditions will eventually stop the vibration.
MECO CORPORA TION LIMITED W ARRANTY This product is warranted to the original consumer purchaser against defects in material and workmanship under normal outdoor household use and correct assembly (if assembled by the consumer-purchaser). Burner and Cooking Grid are warranted for a period of one (1) year from the date of purchase.
P/N 03.6602.01 REV . 20071 129 Aussie ®.
デバイスMeco 7110.7.641の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Meco 7110.7.641をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはMeco 7110.7.641の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Meco 7110.7.641の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Meco 7110.7.641で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Meco 7110.7.641を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はMeco 7110.7.641の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Meco 7110.7.641に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちMeco 7110.7.641デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
