Mieleメーカー05 536 980の使用説明書/サービス説明書
ページ先へ移動 of 64
Operating instructions f or W ashing machine PREMIER NO V O It is essential to read these operating instructions before installing or using the machine, to avoid the risk of accidents, or damage to the machine.
Disposal of the packing material The transport and protective packing has been selected from materials which are envir onmentally friendly for disposal and can normally be recycled. Ensure that any plastic wrappings, bags etc. are disposed safely and kept out of the reach of babies and young children.
Caring for our en vironment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Disposal of the packing material . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Disposal of your old appliance .
Programmes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 Programme selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 Sequence . . .
Prob lem solving guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44 The programme does not start. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44 The wash programme stops and a fault indicator light comes on.
Front vie w a Electric supply cable b Inlet hose (able to withstand pres - sures of at least 70 bar) c Flexible drain hose (with detachable swivel elbow) d Detergent dispenser drawer e Facia panel wit.
Control panel a I-ON/0-OFF button T o switch the machine ON or OFF or to interrupt a programme. b Door button Opens the machine door . c ST ART button Starts the wash programme d Buttons for ad ditional functions The upper button is used to select ei- ther the Soak , pre-wash or Short wash additional option.
Read the operating instructions be - fore using this machine for the first time. They contain important infor - mation about the safety , use and maintenance of the machine.
This machine must only be con - nected to the on-site water supply using a new hose kit. Old hoses must not be re-used. Check the hose r egu - larly for signs of wear and tear . Change in good time to avoid the risk of leaks and subsequent damage. Faulty components must only be exchanged for Miele original spare parts.
If the correct amount of detergent is dispensed, the machine should not need to be descaled. If, however , you do wish to descale the machine only use proprietary non-corrosive descaling agents and strictly observe the instructions on the packaging. If in doubt, contact the Miele Customer Ser - vice Dept.
– W ater consumption and energy us - age are determined by the size of the load. Load to the maximum recom - mended for the programme selected. – The washing times can vary consid - erably due to the automatic load ad - justment feature. Depending on the amount of the load, the main wash may be shortened and one rinse omitted.
Before using the machine for the first time ensure that it is corr ectly in - stalled and connected. See the rele - vant section under "Installation". Also check that the fluff filter is se - curely tightened. Otherwise ther e is a risk of water leakage during use.
Brief guide The headings numbered ( A , B , C ,...) show the operating sequence and can be used as a brief guide. Before washing A Sort the laundr y . ^ Empty all pockets. Foreign objects (e.g. nails, coins, paper clips, etc.) can cause dam - age to textiles and components in the machine.
B Press the Door button. C Load the drum. Unfold washing and load loosely in the drum. T o achieve best results it is ad - visable to make up mixed loads con - sisting of both large and small items. This improves the washing ef fect and helps distribute the load evenly to keep the machine stable and reduce the noise level during spinning.
I Select any ad ditional option re - quired. A maximum of two additional options can be chosen, provided they ar e com - patible with the programme selected, (see the Programme survey in the Sec - tion on programmes). Only one option out of Soak , Pre-wash and Short wash can be selected.
At the end of a programme When the Finish indicator light comes on the laundry can be removed from the drum: L Press the Door button. M Press and release the I-ON/0-OFF button and turn the pr ogramme se - lector to the Finish position. N Remove the washing.
Adding or remo ving washing after programme start W ashing can be added or removed af - ter the programme has alr eady started, when using the following programmes. – COTTONS – MINIMUM IRON – WOOLLENS / – QUICK W ASH – Starch – MIXED W ASH ^ Press the Door button and hold it until the door springs open.
Programme . . . . . . interruption ^ Press the I-ON/0-OFF button. ^ T o continue with the same programme pr ess the I-ON/0-OFF button again. . . . alteration The machine will accept the following chan.
All modern detergents produced for automatic washing machines are suit - able, including liquid, compact (con - centrated), tablets, liquid tablets and special application detergents. Use dis - pensing aids, e.g. balls, if these are supplied with the detergent.
Adding deter gent i = Compartment soak/pre-wash. This compartment is also used for starch formulations when starching separately . j = Compartment main wash p = Compartment fabric conditioner W ater is taken in through compartment i in the pre-wash. W ater is taken in through compartment j in the main wash.
A utomatic fabric conditioners, texturiser s, or liquid starc h ^ Open the lid of compartment p . ^ Add the fabric conditioner , texturiser or liquid starch. Do not e xceed the maximum le vel mark. ^ Close the compartment lid. ^ Push the drawer back in.
Programme selection Programme Fabric T emperature max. spin speed CO TTONS e Cottons and linen fabrics, e.g. bed linen, table linen, towelling, jeans, underwear , T -shirts, nap - pies.
max. load Ad ditional options Notes 5 kg – Soak – Pre-wash – Short – W ater plus (Option 1,2,3,4) With heavily soiled items select Soak or Pre-wash . W ash dark colours in liquid detergent. For normally soiled items select Short . 5 kg For test institutes: Programme setting for tests according to EN 60456 Stan - dard Programme 2.
Sequence CO TTONS 1) MINIMUM IRO N 1) DELICA TES W OOLLENS / Soak optional optional optional – Pre-wash optional optional optional – Main wash ßßßß T op-up rinse from 75°C programmable – – – Graduated rinsing – from 50°C – – No.
Quick W ash Star ch Spin Separate rinse MIXED W ASH 1) high cotton content high polyester content –––– optional optional – ß – – optional optional ß ––– ßß –––––– ––––– ß 2 2 – – – – – – – 2 – – 3 or 4 2) 2 2 3 2 2 max.
Care symbols - washing Care symbols Fabric types Description of process Programme: (select the appropriate temperatur e ac - cording to the temperatur e on the care label symbol) e no bar Cottons Norm.
Important - other care symbols / Hand wash (if a temperature is not specified, use the low - est temperature or cold) h Do not wash apf Dry clean D Do not dry clean y Suitable for chlorine bleach - in.
T o select an additional option to the ba - sic programme pr ess the button for that option. The indicator light for the option comes on. If an additional option is chosen which is incompatible with the basic programme, (see Pr ogramme selection chart), the indicator light goes out when the button is released.
W ater plus The water level increases in soak , pre-wash , main wash and / or rinses , and / or an extra rinse can be carried out. Y ou can choose between four options for the W ater plus button. The options can be called up through one of the programmable functions, (see W ater plus system in the Section on programmable functions).
Electronic pr ogramme locking Programme locking pr events the ma - chine from being opened or the programme cancelled during a wash programme. Switching on pr ogramme locking ^ Select a programme, (see Brief guide to washing correctly). ^ Press the ST ART button for at least 5 seconds.
Programmable functions enable the user to introduce further features as requir ed. They remain stor ed in memory until they are cancelled by the user . Maximum water le vel The water level for rinsing is automat - ically raised to the maximum level where rinse r esults are particularly important.
W ater plus system The W ater plus button offers four op - tions, increasing water level and / or bringing in an extra rinse cycle. T o activate the option press the W ater plus button when selecting your wash programme befor e pressing the ST ART button.
Selecting the Options By pressing the ST ART button you can select the other options. T o confirm a new selection another indicator light co - mes on and the previous one goes out.
Activating the i compartment This function should be activated if traditional "big box" detergents are used. For the first 10 seconds of the Cottons main wash cycle water flows in through compartment i . Compartment j may sometimes not be able to hold the total amount of de - tergent requir ed when: - the water is very hard (over 3.
Soak time This is accessed for a programme by pressing the SOAK button on the fa - cia. Y ou can programme a soak time of: - 2 hours (factory setting) or - 1 hour 30 mins or - 1 hour or - 30 mins. A "Soak time" of 2 hours is set at the factory .
Gentle action For gentle washing of slightly soiled items. Drum action is reduced. Gentle action can be used with the COTTONS, MINIMUM IRON, QUICK W ASCH, MIXED W ASH - Poly/Cottons and Starch programmes. If "Gentle action" has been pro - grammed, every wash cycle in these programmes is carried out with gentle action rhythm.
T op-up rinse for Cottons At the end of the main wash addi - tional water flows into the drum to cool the suds down. Hot suds can damage plastic drainage pipes.
Memory function If an additional option is selected for a programme, and / or the spin op - tion is altered, the machine stor es these changes in memory at the star t of a programme. The memory function is active when the machine is first delivered but can be programmed to be switched of f.
Cleaning the washing machine ^ Clean the casing with a mild non-abrasive detergent or soap and water . Wipe dr y with a soft cloth. ^ Clean the facia panel and lid with a damp cloth and dry with a soft cloth. ^ The drum can be cleaned using a suitable proprietary stainless steel cleaner .
Cleaning the detergent dispenser drawer ^ Pull out the detergent dispenser drawer until a resistance is felt. ^ Press down the r ed release catch and at the same time pull the drawer right out of the machine. ^ Clean the dispenser compartments and conditioner channel.
Cleaning the fluff (drain) filter and pump Check the fluff (drain) filter initially after 3-4 washes to ascertain how often it is likely to requir e cleaning. With normal cleaning approx. 2 litres of water run out. If the drain outlet is clogged, more wa - ter will be retained in the machine (up to 25 litres) .
^ Once the flow of water ceases, re - move the fluff filter completely . ^ Clean the fluff filter thor oughly . ^ Remove any foreign objects (e.g. buttons, coins, etc.) and fluff. ^ T ur n the impeller by hand to check that it is free to r otate. Any foreign ob- jects causing an obstruction should be removed.
T o clean the water inlet filter s The washing machine has two filters to protect the inlet valves.These filters should be checked every 6 months or so, or more often if ther e are fr equent interruptions to the water supply . T o c lean the filter in the union in the open end of the inlet hose: ^ First turn off the stopcock.
With the help of the following notes minor faults in the perfor mance of the appli - ance, some of which may result fr om incorrect operation, can be put right without contacting the Service Department.
The wash programme stops and a fault indicator light comes on. What to do if ... P ossible cause Remedy The Check drain indica - tor light is flashing. The water outlet is blocked. Clean the fluff (drain) filter and drain pump. The drain hose has been fixed too high.
A fault indicator light comes on but the wash pr ogramme continues as normal. What to do if ... Possib le cause Remedy The Check drain light flashes. The drain outlet is restricted. Clean the fluff (drain) filter and drain pump. The Check inlet light flashes.
General prob lems or an unsatisfactory wash result What to do if . . . P ossible cause Remedy The machine shakes during the spin cyc le. The four feet are not resting evenly on the floor . Level the machine. See advice on installation. The laundry has not been spun satisfacto - rily .
What to do if ... P ossible cause Remedy The pump makes strange noises. These do not indicate a fault. They occur at the end of a pump sequence as a normal par t of the operation. Large residues of de - tergent remain in the dispenser drawer . The water supply pres - sure is too low .
What to do if . . . P ossible cause Remedy Grey , greasy par ti - cles c ling to washed laundry . Insufficient amounts of detergent were used to break down the particles of grease in heavily soiled laundry . – Add more detergent. – Before washing the next load run a COTTONS 95°C programme with powder de - tergent but without a load.
Opening the drum door in the event of a po wer failure ^ Switch off the washing machine. ^ Open the fluff (drain) filter flap and drain the water as described in "Cleaning and care", (fluf f (drain) filter and pump). Caution: if laundry has been washed at a high temperature, water drain - ing out of the machine will still be hot.
Customer contact In the event of any faults which you cannot remedy yourself please contact – Y our Miele Dealer or – Y our nearest Miele Service depart - ment (see back cover for the ad - dress). When contacting the Service Depart - ment, please quote the Model and Se - rial nos.
Installation surface A concrete floor is the most suitable in - stallation surface for a washing ma - chine, being far less prone to vibration during the spin cycle than wooden floorboards or a surface with "soft" properties. Please note the following points: ^ The machine must be level and se - curely positioned.
B T ur n the right-hand transit bar 90°. C Withdraw the two bars together with the support plate. D Plug the two holes with the plastic caps supplied. , The washing machine must not be moved without the transit bars in place. Store the transit bars in a safe place for future use.
Levelling the mac hine The machine must stand perfectly level on all four feet to ensure safe and proper operation. Incorrect installation may incr ease elec- tricity and water consumption and may cause the machine to move about. The four adjustable screw feet ar e used to level the machine.
Building under a worktop ^ A special building under conversion kit* is requir ed which includes a cover plate to replace the machine’s lid. ^ Fitting instructions are supplied with the conversion kit. N.B. Cover plate The cover plate must be fitted in place of the machine’s lid to ensure electrical safety .
Connection to water supply The machine should be connected to a mains water supply in accordance with standard r egulations. In Germany the washing machine is not requir ed to have a non-return valve as it has been designed to comply with the relevant German DIN standard.
Connection to the drainage system The machine drains via a drain pump with a delivery head of 1 metre. The drain hose is 1.5 m long. It must not be kinked as this restricts drainage. The swivel elbow at the end of the hose can be turned in either direction, or can be detached if requir ed, with a sharp twist and pull.
Electrical connection U .K. All electrical work should be carried out only by a suitably qualified and compe - tent person, in strict accordance with national and local safety regulations. The appliance is supplied with a mains cable with moulded plug for connection to a 230-240V mains supply .
Electrical connection U .K. Non-rewireab le plugs BS 1363 If this machine is fitted with a non-rewir eable plug, the following infor - mation applies: If the socket outlets are not suitable for the plug supplied with the product, it must be cut off and an appr opriate plug fitted.
Programme (without any additional op - tions or programmable functions) Load Consumption data Energy W ater Programme time in kWh litres normal short CO TTONS 95°C 5.0 kg 1.70 52 1 h 54 mins 1 h 26 mins 60°C* 5.0 kg 0.95 52 1 h 58 mins 1 h 16 mins 40°C 5.
Height 85.0 cm Width 59.5 cm Depth 60.0 cm Depth with door open 97.0 cm Weight 92 kg Max. floor load 1600 Newton (ca. 160 kg) Capacity 5 kg Dry laundr y V oltage see Data plate Rated load see Data plate Fuse rating see Data plate W ater flow pressur e min.
62.
63.
M.-Nr . 05 536 980 / V02 Alteration rights reserved/3002 This paper consists of cellulose which has been bleached without the use of chlorine..
デバイスMiele 05 536 980の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Miele 05 536 980をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはMiele 05 536 980の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Miele 05 536 980の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Miele 05 536 980で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Miele 05 536 980を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はMiele 05 536 980の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Miele 05 536 980に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちMiele 05 536 980デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
