Ariensメーカー911086 - LM21, 911087 - LM21Sの使用説明書/サービス説明書
ページ先へ移動 of 22
Owner/Operator Man ual Models 91 1086 - LM21 91 1087 - LM21S W alk Behind Lawn Mower 01 1982 00A 2/04 Super sedes 01 1 98200 Printed in USA ENGLIS H FRANÇAI S ESP AÑO L T ransfer model & serial number label from product registration here. Coller l’autocollant du modèle et du numéro de série dans cet encadré.
3 ENGLIS H 1. Engine Control 2. S peed Control Rod (S elf- propelled) 3. Primer 4. Side Discharge Cover 5. Side Discharge Deflector 6. Cutting Height Levers (2 Rear Wheel Adjusters, 2 Front Wheel Adjusters) 7. Rear Door 8. Adjustable and Folding Handlebars 9.
GB - 4 Controls a nd Fe a t ure s . . . . . . . . . . . . . 3 Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Assembly . . . . . . . . . . . . . . . . . . . . . . . . 9 Operati on . . . . . . . . . . . . . . . . . . . . . . . 10 Mainten ance .
GB - 5 5. Instruct cust omer on cont rols and operation of unit. Discuss and emphasize the Safet y Rules. Give customer Owner/Operator , Parts, and Engine manuals.
GB - 6 SAFETY DECALS AND LOCATIONS AL WA YS replace missing or damaged safet y decals. Refer to Figure 3 for safe ty decal locations. 1. DANGER TO A VOID SE RIOUS INJUR Y OR DEA TH 2. DANGER KEEP HANDS AND FEE T A W A Y Do not operate mower unless guards are in operating position or bagger is attached.
GB - 7 SAFETY RULES If unit is to be used by someone other than original purchaser; loaned, r ented or sold, AL WA YS provide this manual and any needed safety training before o peration. Read, understand and f ollow all safety practices in Ow ner/Operator Manual b efore beginning assembly .
GB - 8 S top engine before removing and em ptying grass bag. When mulching or bagging, AL W A YS install discharge cover . When side discharging, AL WA Y S install side discharge deflector . AL WA YS shut off engi ne, allow blade to stop and disconnect spark plug wire before clearing clogs or cleaning unit.
GB - 9 Replace worn-out mufflers immediately . Continued use could result in fire or explosion. Sharp edges can cut or amputate fingers or a hand. Wrap bl ade or wear sturdy gloves to service. Use only replaceme nt parts designed for your unit. See your Ariens Dealer .
GB - 10 CONTROLS AND FEATURES See Figure 1 for locations. Engine/Blade Control The engine/blade control must be held against the handlebar to start the engine and blade. Releasing the control during operation stop s the engine and blade. Hand leba r Adjust handlebar t o a safe and co mfortable height.
GB - 1 1 OPTIONAL CONTROLS Primer Bulb Push the primer bulb in to add fuel f or easier engine start. S peed Control (self-pro pelled mode ls) S peed control rod changes the mower ’s forward travel speeds. High –Push lever all the way forward. Low –Pull lever all the way rearward.
GB - 12 FILLING FUEL T ANK T o add fuel to fuel tank: 1. Put unit in open or well -ventilated area. 2. S t op engine and allow t o cool. 3. Clean fuel cap and surrounding area. 4. Remove cap. IMPORT ANT : See engine manual for correct type and grade of f uel.
GB - 13 2. For engines with a primer , push primer bulb 2 or 3 times for a cold engine. NOTE: It is unneces sary to prime or choke a warm engine. 3. With engine/blade control held against the handlebar , grasp starter handle and pull rope slowly unt il it pulls harder .
GB - 14 CHECK WHEEL DRIVE CONTROL (self-propelled models) The unit must stop quickly and complet ely when the control is released. Adjust or repair if necessary . See Service and Adjustments . CHECK GRASS BAG Check grass bag frequently for wear or deterioration.
GB - 15 NOTE: Loose spark plug wire terminals can cause sparking. Replace terminal if damaged. CHECK ENGINE COOLING T o prevent overheating, air must circulate freely around the c ooling fins, cylinder head and block. Every 100 hours of operation or yearly (more often if conditions require) remove blower housing and clean coo ling fins.
GB - 16 ENGINE/BLADE CONTROL ADJUSTMENT T o adjust engine/blade control: 1. Loosen cable nuts away from bracket. 2. Squeeze z-bend brac ket at engine end of cable toward front of unit and hold in place. 3. Pull cable down from bracket until there is no slack in cable.
GB - 17 DRIVE BELT REPLACEME NT (self-propelled models) T o remove drive belt: 1. Set the right rear wheel to its lowest cutting height, and the left rear wheel to the third cutting height. This position provides clearance between friction disc and drive sheav e.
GB - 18 SPEED CONTROL BELL CRANK (self-propelled unit s) The speed con trol bell crank holds the sp eed control rod in po sition after a speed has been set. The spring washers may become loose with normal wear . If the speed control rod does not stay firmly in posit ion, adjust the speed control bell c rank.
GB - 19 T ROUBLESHOOTING PROBLEM PROBABLE CAUSE CORRECTION Engine wi ll not st art 1. Fuel tank empty or low . 2. S park plug wire loose or off. 3. Engine/Blade control cable detached, broken, or not adjusted properly . 1. Check fuel level. Fill tank if necessary .
GB - 20 SERV ICE PART S Always use genuine Ariens part s to keep your mower running like new . Mower Model 91 1086 91 1087 Air Filter 21535600 Fuel Filter 21533900 Blade 01 1370 00 ACCESSORIES See your authorized Ariens dealer to add these optional accessories.
GB - 21 SPECIFI CATIONS Model Number 91 1086 91 1087 Description LM21 LM21S Length - in (cm) 61.5 (156) Height - in (cm) 38 (96,5) Width - in (cm) 23 (58,4) Actual Weight - lbs (kg) 77 (35) 93 (42,27) Cutting Width 21 (53,3) Cutting Height - in. (cm ) 6 Positions: 1.
GB - 22.
Ariens Co mpany 655 West Ryan S treet P .O. Box 157 Brillion, WI 541 10-0157 920-756-2141 Fax 920-756-2407 www.arien s.co m.
デバイスAriens 911086 - LM21, 911087 - LM21Sの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Ariens 911086 - LM21, 911087 - LM21Sをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはAriens 911086 - LM21, 911087 - LM21Sの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Ariens 911086 - LM21, 911087 - LM21Sの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Ariens 911086 - LM21, 911087 - LM21Sで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Ariens 911086 - LM21, 911087 - LM21Sを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はAriens 911086 - LM21, 911087 - LM21Sの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Ariens 911086 - LM21, 911087 - LM21Sに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちAriens 911086 - LM21, 911087 - LM21Sデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。