MieleメーカーKFN 14943 SD edの使用説明書/サービス説明書
ページ先へ移動 of 18
Operating and Installation Instructions Fridge-Freezer Combination KFN 14943 SD ed To prevent accidents and machine damage read these instructions before installation or use.
, Avoid the risk of electrical shock - Plug into a grounded 3-prong outlet. - Do not move the ground plug. - Do not use an adapter. - Do not use an extension cord. Failure to follow these instructions can result in death, fire, or electrical shock. Improper connection of the equipment grounding conductor may result in electric shock.
Do not place any devices that produce heat (such as a toaster or microwave) on top of the appliance. This would increase the energy consumption of the appliance! This fridge/freezer should not be placed side-by-side with a second model.
Adjustments ^ Use the wrench provided to adjust the feet as needed, so that the appliance is level. ^ If necessary, unscrew the foot a from the hinge bracket in order to support the appliance door.
Appliance dimensions ABC KFN 14943 SD ed 2020 750 630 Installation information 48.
The appliance comes with right-hand hinging. If left-hand door hinging is preferred, then follow these instructions to change the door hinge: You will need the following tools: – a crosstip screwdriver, – a flathead screwdriver, – various sizes of Torx screwdrivers, – a fork wrench.
Before changing the hinging, remove any items of food from the shelves in the appliance door. Removing the top soft-close mechanism: ^ Open the top door of the appliance. ^ Loosen the panel a from the soft-close mechanism: From below, slide a flathead screwdriver into the recesses, then slowly and carefully lift off the panel.
^ Remove the cover d . Now the soft-close mechanism and the appliance are no longer connected. ^ Remove the panel a . ^ Push the shock absorber arm f as far as possible towards the handle side. ^ Loosen the three screws g on the soft-close mechanism and the spacer.
Caution! The top door of the appliance is no longer secured as soon as the hinge bracket is removed when following the instructions below! ^ Close the top door of the appliance. ^ Loosen the screws m on the top hinge bracket n and remove the hinge bracket by pulling up.
^ Push the pin e up and out. Now the soft-close mechanism and the appliance are no longer connected. ^ Remove the panel a . ^ Push the shock absorber arm f as far as possible towards the handle side. ^ Loosen the three screws g on the soft-close mechanism and the spacer.
^ Lift the plugs l out of the door bearing bushing in the appliance door and place it on the other side. Mounting the bottom door of the appliance: ^ Remove the cover a towards the front. ^ Pull the cover b off. ^ Screw the adjustment foot at the bearing pin c completely in.
^ Put the bearing pin i in the middle of the appliance through the hinge bracket k into the bottom door of the appliance. Mounting the bottom soft-close mechanism: ^ Remove the cover a from the panel b , turn it 180° and replace it on the other side.
^ Hang the panel b on the shock absorber arm d . ^ Pull the shock absorber arm d towards the hinge bracket and insert the pin e from the top so that the square rests in the recess. ^ Put on the cover f in such a way that it engages. Take care that the cover f sits correctly to ensure that the door closes properly and the pin is secured.
Mounting the top soft-close mechanism: ^ Remove the cover a from the panel b , turn it 180° and replace it on the other side. ^ Hook the spacer on the handle side into the retainer (A). ^ Hook the soft-close mechanism into the retainer (B) on the appliance side.
^ Remove the securing device g . ^ Place the panel b onto the soft-close mechanism from above, engaging it at the bottom first and then at the top. ^ Close the top door of the appliance. Remounting the door handles: The following instructions must be followed when attaching the door handle, otherwise the door seal could be damaged.
The appliance doors can be aligned with the appliance housing afterwards. In the following figure, the appliance door is not closed so that the individual steps can be seen more clearly. Align the bottom door in the bottom hinge bracket via the outer, elongated holes: ^ Remove the middle screw a from the hinge bracket.
a adapter cabinet b appliance c kitchen cabinet d wall The appliance can be installed in any fitted kitchen. To match the appliance to the height of the fitted kitchen, a suitable adapter cabinet a can be installed over the appliance. A ventilation gap of at least 2 inches (50 mm) must be provided between the adapter cabinet and the kitchen wall.
Subject to change without notice / 4709 KFN 14943 SD ed M.-Nr. 07 589 450 / 01.
デバイスMiele KFN 14943 SD edの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Miele KFN 14943 SD edをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはMiele KFN 14943 SD edの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Miele KFN 14943 SD edの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Miele KFN 14943 SD edで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Miele KFN 14943 SD edを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はMiele KFN 14943 SD edの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Miele KFN 14943 SD edに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちMiele KFN 14943 SD edデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
