Mieleメーカーt 250 cの使用説明書/サービス説明書
ページ先へ移動 of 48
Operating instructions f or condenser tumb le dr y er T 250 C T o avoid the risk of accidents or damage to the machine it is essential to read these operating instructions before it is installed or used for the first time.
W arning and Safety instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Caring for the en vironment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Disposal of the packing material .
Cleaning the condenser unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 Removing the condenser unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 Checking the condenser unit . .
T o avoid the risk of accidents and damage to the machine please read these instructions carefully befor e using it for the first time. They contain important infor mation on its safety , use and maintainence. Keep these operating instructions in a safe place and ensure that new users are familiar with the content.
If the connection cable is faulty it must only be replaced by a Miele approved service technician to pr otect the user from danger . In the event of a fault or for cleaning purposes, the machine is on.
Always close the door after use. This way you will avoid the danger of: – children climbing onto or into the dryer or hiding things in it. – pets or other small animals climbing into it. Do not let anyone sit or lean on the door , as this can cause the machine to tip up.
Disposal of the packing material The transport and protective packing has been selected from materials which are envir onmentally friendly for disposal and can normally be recycled. Ensure that any plastic wrappings, bags etc. are disposed of safely and kept out of the reach of babies and young children.
Control panel a ST ART button Press the ST ART button to start a programme. The Start indicator lamp will flash as soon as a programme can be started. It lights up constantly once the programme has started.
Future updates (PC) The indicator lamp marked PC on the fascia panel is the interface used by the Miele service technicians for updating the machine’s programme data. Electronic system loc k and programmab le functions The following can be programmed into your machine using the programme selector in combination with the buttons.
W ash care labels Before drying check the drying symbol on the wash care label. Significance of symbols: q Dry at nor mal temperature r Dry at low temperature s Do not tumble dry If no symbol is featu.
Programmes Fabric type Special notes Drying levels CO TTONS maximum load: 5 kg (1) Extra dry Multi-layered fabrics, which would not be thoroughly dried using the "Normal +" programme. Do not dry jersey wear in the Extra dry programme - tendency to shrink.
Programme Fabric type Special notes Drying levels MINIMUM IRON maximum load: 2.5 kg (1) Normal + Minimum iron items which ar e made of synthetic or blended fabrics (e.g. pullovers, dresses, tr ousers) which are not dried adequately in the "Normal" programme.
Programme Fabric type Special notes Special care programmes W oollens hand care maximum load: 2 kg (1) Woollen fabrics T o refr esh and fluff up woollen garments quickly . Remove garments immediately at the end of the programme. Do not r epeat. Woollen fabrics ar e not dried completely by this programme.
A Prepare the laundry ^ As far as possible, sort laundr y for: - the type of fibre or weave, - the degree of dryness requir ed, - similar size of items, - the moisture content after spinning. This will help towards achieving an even drying result. Fasten duvet covers etc.
C Select a programme ^ T ur n the programme selector to the requir ed programme. COTTONS and MINIMUM IRON The electronic unit uses the r esidual moisture content to estimate the programme duration. This is an approximate drying time. See "Consumption data" chart for programme durations.
Short For drying fabrics which can withstand high temperatures, e.g. pure linens and cottons. Do not use on minimum iron or delicate fabrics. – Because the heater rating is increased clothes dry faster thus shortening dr ying times. Low temperature For drying delicate fabrics with the symbol r (e.
Additional notes ... Clean out airways indicator lamp This indicator lamp comes on to warn you that the dryer is not working efficiently . This may be because: – the fluff filters ar e clogged; – the condenser unit is clogged.
Changing a programme If the programme selector is turned to a differ ent programme after a pr ogramme has begun, this will not affect the programme. The Anti-crease / Finish indicator lamp will flash. The indicator lamp will go out when the selector is returned to its original position.
The system lock prevents anyone from interfering with the dryer . If the system lock has been activated it is not possible to start a programme. The following steps ( A , B , C ...) must be carried out in the correct order . T o activ ate the system lock A Ensure that the door is closed and that the programme selector is turned to Finish .
Emptying the condensed water container The condensed water will be collected in the condensed water container unless the machine has been fitted with a drain hose (see installation). The condensed water container should be emptied after every drying cycle or as soon as the Empty out container indicator lamp comes on.
Cleaning the fluff filters The fluff which is cr eated by the drying process is collected by the fluf f filters in the door and the door opening. Clean the filters after each drying programme. Cleaning them whilst dry ^ Open the door and pull the fluff filter out of the door as illustrated.
Cleaning them with water If there is a gr eat deal of compacted fluff on any of the filters, they can be removed and cleaned under hot running water . ^ T o remove the fluf f filter from the door holder see previous page. ^ Grip the holder and push the filter in the door opening upwards in the direction of the arr ow to remove it.
Cleaning the condenser unit Detergent residue, hair and fine fluf f from the dryer can get through the fluf f filters and block the condenser unit. Dust from the r oom in which the dryer is installed can also get into the condenser unit and cause a blockage.
^ Pull the condenser unit out of its housing by the handle. Checking the condenser unit ^ Hold the condenser unit up to the light as shown . ^ Check to see if there is any fluf f inside it. The arrows in the illustration above indicate where to look. If you cannot see any fluff: ^ Replace the condenser unit (see following page).
^ Then flush the unit through fr om the front. ^ Check the condenser unit again for any visible fluff and if necessary flush it through again until it has all gone. ^ Remove any soiling still visible inside the housing unit. ^ Also make sure the rubber seals ar e clean.
With the help of the following notes minor faults in the perfor mance of the machine, some of which may result fr om incorrect operation, can be put right without contacting the Service Department.
Prob lem P ossible cause Remedy There is a build up of fluff. Fluff is principally the r esult of friction when garments are being worn and washed. Machine drying hardly causes any fluf f to form and has been established by resear ch institutes to have no effect on the lifetime of fabric.
Prob lem P ossible cause Remedy The drying process goes on too long or even s witches off. Important : Before attempting to remedy one of the following causes, switch the dryer off and switch on again to start the programme again. V entilation to and from the dryer may be insufficient (e.
Prob lem P ossible cause Remedy The condenser unit service panel will not shut. The inner cover of the condenser unit has not been locked properly and/or the condenser unit has not been positioned correctly . – Ensure that the condenser unit is positioned correctly and lock the cover .
Prob lem P ossible cause Remedy The Clean out airways lamp comes on. The fluff filters may be blocked. Remove any fluff (see "Cleaning and care"). The condenser unit may be blocked with fluff and detergent residues. Please note that the condenser unit must be cleaned regularly (see "Cleaning and care").
Prob lem P ossible cause Remedy The programme has stopped. The Anti-crease/Finish lamp has come on in the sequence display and the buzzer is sounding. This is not a fault. The electronic unit has recognised that ther e is no laundry in the drum and cancelled the programme.
T o c hange the interior drum lamp ^ Open the door . Before changing the lamp, disconnect the machine from the mains power supply . Y ou will find the interior lamp cover at the top of the drum aperture. ^ Insert the opener under the side edge of the cover as illustrated.
After sales service Repairs In the event of any faults which you cannot remedy yourself, please contact – Y our Miele Dealer or – The nearest Miele Service Department (see back cover for address).
Front vie w a Supply cable for electrical connection b Condensed water container c Control panel d Door e Service panel for condenser unit f Four height-adjustable screw feet g External drainage options (e.g. via wash basin, wash basin drain outlet, or gully).
Installation site , Make sure the dryer door can be opened without hindrance after installation. T ransporting the machine to its installation site When moving the machine you can hold it by the lid where it pr otrudes to the rear of the dryer .
Aligning the machine The machine must be perfectly level to ensure safe and pr oper operation. ^ The screw feet can be adjusted to compensate for any unevenness in the floor . , The ventilation gaps in the plinth must not be covered over as this would prevent a suf ficient intake of air .
External condensed water outlet When drying is in progress, condensed water is pumped into the condensed water container through the drain hose at the back of the dryer . The condensed water can also be drained off dir ectly if the machine is installed near a sink, drain outlet etc.
Connection to a sink drain outlet The drain hose can be connected directly to a sink drain outlet. ^ Remove the following from the back of the dryer at the bottom: Adapter 1 and hose clip 3 behind it. ^ Fit adapter 1 to the sink drain outlet using nut 2 .
Electrical connection U .K. All electrical work should be carried out only by a suitably qualified and competent person, in strict accordance with national and local safety regulations. Ensure power is not supplied to the machine while installation work is being carried out.
If the colours of the wires in the mains lead of this machine do not correspond with the coloured markings identifying the terminals of your plug, proceed as follows: ^ The wire which is colour ed gre.
Programme Capacity Final spin speed (in a domestic washing machine) Electricity consump- tion Drying time incl. cooling down time kg rpm kWh Minutes CO TT ONS Extra dry 5.0 1200 1400 1600 3.25 3.10 2.85 86 83 76 Normal + 5.0 1200 1400 1600 2.80 2.65 2.
Height 85 cm (adjustable +0.7/- 0.7 cm) Height without lid 82 cm Width 59.5 cm Depth 58 cm Depth with door open 106 cm Weight 54 kg Drum volume 100 litres Maximum capacity 5 kg dry weight Capacity of condensed water container approx. 3.5 litr es Length of connection cable 1.
Progr ammable functions f or changing standard settings 43.
Increased drying level The machine is designed to dry using as little energy as possible. However , if you require the laundry to be drier , it is possible to reduce the final moisture level in the COTTONS and MINIMUM IRON programmes. Note that programme durations will be longer if this option is activated.
Memory function The additional options selected previously for specific pr ogrammes are stor ed in the machine’s memory . The machine is supplied ex-works with the memory function switched off.
46.
47.
M.-Nr . 05 993 030 / 01 Alteration rights reserved/4703 This paper consists of cellulose which has been bleached without the use of chlorine..
デバイスMiele t 250 cの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Miele t 250 cをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはMiele t 250 cの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Miele t 250 cの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Miele t 250 cで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Miele t 250 cを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はMiele t 250 cの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Miele t 250 cに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちMiele t 250 cデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
