MieleメーカーT 8005の使用説明書/サービス説明書
ページ先へ移動 of 44
Vented Dryer T 8002 T 8003 T 8005 To prevent accidents and appliance damage read these instructions before installation or use. M.-Nr. 06 879 010 en - US, CA.
IMPORTANT SAFETY INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Control panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Before loading the dryer . . . .
, WARNING - To reduce the risk of fire, electric shock, or injury to persons when using your appliance, follow basic precautions, including the following: ~ It is essential to read all instructions before using the appliance. ~ Do not allow children to play on or in the appliance.
~ Allow the dryer to complete each stage of the program selected, including the cooling down phase. This will ensure that the items being removed are not too hot to handle ~ Clean the lint filter before or after each load. ~ Keep the area around the air intake (toe-kick) and adjacent surrounding areas free from lint, dust and dirt.
a e- "Programs" buttons For selecting a drying program. b "Options" buttons For selecting a drying option. c "Dryness" button For selecting the dryness level of the finished laundry. d "Status" display Shows the current cycle of the drying program.
The dryer must be correctly installed and connected before the first use. Please refer to the "Installation Instructions". ^ Before using for the first time, clean the drum with a cloth. Before drying, check fabric care labels for special drying instructions.
1. Turn on the dryer and load the laundry ^ Press the "On/Off" button to turn on the dryer. ^ Press the "Door" button to open the door. ^ Load the laundry loosely into the drum. ^ Make sure the lint filters are in place. ^ Close the door.
Program When to use Note Normal Available drying options: Turbo, Full load, Gentle, Anti-crease Extra Dry Multi-layer, mixed loads of sturdy cottons, e.g. jeans, towels. The "Extra Dry" program should not be selected for jersey materials. Items may shrink.
3. Select a drying option (if needed) ^ A drying option can be selected or deselected with each press of the button. OPTIONS Turbo Fast drying for sturdy fabrics with increased temperature and a reduced program length. Full load Select this option for efficient drying of a standard size load.
4. Select the dryness level The dryness level can be selected in the "Normal" and "Wrinkle-free" programs. (The dryness level of the other programs cannot be adjusted.) ^ Press the selection button until the desired indicator illuminates.
6. Start the program ^ Press the "Start/Stop" button. Once the program starts, the current cycle of the program will be indicated in the "STATUS" display. 7. At the end of a program The "End/Anti-crease" indicator will light at the end of a program and the buzzer will sound if it was selected.
Canceling or changing a program ^ Press and release the "Start/Stop" button to stop the drying program. To continue drying: ^ Select the new program by pressing the e or - button. ^ Select any desired options. ^ Select a dryness level (available in the "Normal" and "Wrinkle-free" programs).
Child lock When activated, the child lock prevents the dryer from being operated by locking the control panel functions. The dryer can be turned on but not started. The "Child lock" indicator will flash. The door can be opened. To activate the child lock 1.
Cleaning the lint filters , A clogged filter is a fire hazard! The lint filter must be cleaned after every program. ^ Open the door and remove the lint filter, 1 , by gently lifting it upwards. ^ Wipe the lint off the filter with your hand (do not use sharp objects).
Cleaning the grille filters ^ Clean the grille filters in the door opening regularly. While the filters are removed also clean the opening beneath the filters with a dust brush or vacuum. ^ Take the grille filters out by turning the knob at the top of the filter, a , until it clicks and pull them out, b .
Cleaning the exterior and the control panel , To reduce the risk of electric shock, disconnect the dryer from the power supply by shutting off the power main, tripping the circuit breaker or unplugging the power cord before performing maintenance. Never use abrasive cleaners, scouring pads, steel wool or caustic (oven) cleaners on the dryer.
Changing the light bulb , To reduce the risk of electric shock, disconnect the dryer from the power supply by shutting off the power main, tripping the circuit breaker or unplugging the power cord before performing maintenance. ^ Open the door. The bulb cover is located along the upper rim of the drum opening.
What if the dryer will not run? Possible fault Solution The "Start/Stop" button was not pressed. Make sure the dryer is on. Press the "Start/ Stop" button to begin the drying program. The circuit breaker tripped or the dryer is unplugged.
What if the "Filter/Vent" indicator lights after cleaning the exhaust system? Possible fault Solution The dryer is not operating efficiently because the duct hose is too long. Check the exhaust length and diameter (see "How to calculate the effective duct length").
Repairs In the event of a fault which you cannot fix yourself, please contact Miele's Technical Service Dept. When contacting Technical Service, please quote the model and serial number of your appliance. They can be found on the data plate located below the drum opening.
Quick Guide Remove this guide for easy reference Please read all instructions, especially the "Important Safety Instructions", before using the dryer.
1. Turn on the dryer and load the laundry ^ Press the "On/Off" button to turn on the dryer. ^ Press the "Door" button to open the door. ^ Load the laundry into the drum. Make sure that there is enough space in the drum for clothes to tumble freely.
4. Select the dryness level ^ Press the selection button until the desired indicator illuminates. 5. Select the buzzer (if desired) 6. Start the program ^ Press the "Start/Stop" button. 7. At the end of a program The "Anti-crease / End" indicator will light.
Program When to use Note Normal Available drying options: Turbo, Full load, Gentle, Anti-crease Extra Dry For laundry to be folded and shelved immediately, e.g. jeans, towels. The "Extra Dry" program should not be selected for jersey materials.
Installation Instructions To prevent accidents and appliance damage read these instructions before installation or use..
, WARNING - Risk of Fire ~ To reduce the risk of severe injury or death, follow all installation instructions. ~ Clothes dryer installation must be performed by a qualified installer. ~ Install the clothes dryer according to the manufacturer's instructions and local codes.
~ The installation of this unit in non stationary locations (e.g. ships) must be performed by a qualified installer or service agency, in strict accordance with national and local safety regulations and standards. ~ Do not install the machine in rooms where temperatures below freezing may occur.
The tumble dryer can also be placed on top of a Miele washing machine for a stacked installation. An appropriate stacking kit is required. The stacking kit is available from your Miele dealer or the Miele Technical Service Department. , Installation of the stacking kit must be performed by a Miele authorized technician.
GROUNDING INSTRUCTIONS This appliance must be grounded. In the event of malfunction or breakdown, grounding will reduce the risk of electric shock by providing a path of least resistance for electric current. This appliance is equipped with a cord having an equipment grounding conductor and a grounding plug.
a Exhaust connection: The exhaust hose/pipe can be installed either at the rear, left or right of the dryer. b Power cord with plug c Control panel d Door e Four height adjustable feet Installation 26.
Rear view a Handle for easy transport (arrows) b Power cord with plug c Vent connection rear Installation site , Do not install the dryer in a location where its door could conflict with room doors. , This appliance is not intended to be mounted in a wall or other vertical surface of a building or cabinet.
Installation beneath a counter , When removing the machine lid to reduce the height of the machine, a built under spacer kit *i s necessary. It must be installed by a Miele Service Technician. The cover plate of the built under kit replaces the appliance lid and ensures electrical safety.
Leveling the dryer The dryer must be level to ensure safe and proper operation. Minor discrepancies do not however, have an adverse effect on operation.
Installation tips An airflow gap of 3 / 8 " (10 mm) must be provided between the machine and the floor. This airflow gap must not be blocked by a toe-kick or thick piled carpets. Sufficient venting of the installation site, e.g. by opening a window or door, is essential for the dryer's operation.
Exhaust connection Using the connector supplied, an exhaust hose (4" [100 mm] diameter) can be installed. Necessary materials: – a wall or window duct (available from Miele) – an exhaust hose/pipe made of approved non-flammable material ^ Install the exhaust hose/pipe, 2 , with the connector, 1 , to the dryer.
Direct wall connection Necessary materials: – a wall pipe – flexible foam gasket Dryer top view 1 Wall pipe 2 Flexible foam gasket Dryer side view 1 Wall pipe 2 Flexible foam gasket ^ Connect the flexible foam gasket, 2 , to the wall pipe connector, 1 .
How to calculate the effective duct length The overall duct length will determine the duct diameter (see the "Additional duct lengths" table). In Canada the exhaust duct must be 4" (102 mm) in diameter. ^ Measure the actual duct length needed to go from the dryer’s exhaust connection to the vent outlet: 1.
Tips about the duct work – Check with your local building code to determine the maximum allowable duct length. – Only use rigid or flexible metal duct for exhausting.
Additional duct lengths (4" rigid pipe only) Type of bend Radius Additional duct length ft cm ft cm Flexible metal duct – 3’ 3" (1 m) straight – 45° angle – 90° angle 10" 10&q.
Example: Calculating the effective duct length and required internal duct diameter Rigid pipe Duct length ft Duct length m A Wall duct with louvered wall vent 12’ 5" 3.8 m B 90° bend 2’ 7" 0.8 m C 20" (0.5 m) rigid pipe 1’ 7" 0.
Disposal of the packing materials The packing materials protect the appliance during shipping. They have been designed to be biodegradable and recyclable. To prevent suffocation, ensure that any plastic wrappings, bags, etc. are disposed of safely and kept out of the reach of children.
38.
39.
All rights reserved / 0309 For the most updated manual check the Miele web site. M.-Nr. 06 879 010 / 03.
デバイスMiele T 8005の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Miele T 8005をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはMiele T 8005の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Miele T 8005の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Miele T 8005で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Miele T 8005を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はMiele T 8005の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Miele T 8005に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちMiele T 8005デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
