MieleメーカーT 8023 Cの使用説明書/サービス説明書
ページ先へ移動 of 40
Operating and Installation Instructions Condenser Dryer T 8023 C To prevent accidents and appliance damage read these instructions before installation or use.
IMPORTANT SAFETY INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Control panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Before loading the dryer . . . .
, WARNING - To reduce the risk of fire, electric shock, or injury to persons when using your appliance, follow basic precautions, including the following: ~ It is essential to read all instructions before using the appliance. ~ Do not allow children to play on or in the appliance.
~ Allow the dryer to complete each stage of the program selected, including the cooling down phase. This will ensure that the items being removed are not too hot to handle ~ Clean the lint filter before or after each load. ~ Keep the area around the air intake (toe kick) and adjacent surrounding areas free from lint, dust and dirt.
a e- "Programs" buttons For selecting a drying program. b "Options" buttons For selecting a drying option. c "Dryness" button For selecting the dryness level of the finished laundry. d "Status" display Shows the current cycle of the drying program.
The dryer must be correctly installed and connected before the first use. Please refer to the "Installation Instructions". ^ Before using for the first time, clean the drum with a cloth. Before drying, check fabric care labels for special drying instructions.
1. Turn on the dryer and load the laundry ^ Press the "On/Off" button to turn on the dryer. ^ Press the "Door" button to open the door. ^ Load the laundry loosely into the drum. ^ Make sure the lint filters are in place. ^ Close the door with a firm swing - do not push it shut.
Program Fabric Note Normal Available drying options: Turbo, Gentle, Anti-crease Extra Dry Multi-layer fabrics, mixed loads of sturdy cottons, e.g. jeans, towels. The "Extra dry" program should not be selected for jersey materials. Items may shrink.
3. Select a drying option (if needed) ^ A drying option can be selected or deselected with each press of the button. OPTIONS Turbo Fast drying for sturdy fabrics with increased temperature and a reduced program length. Gentle For drying delicate fabrics slowly at a lower temperature.
4. Select the dryness level The dryness level can be selected in the "Normal" and "Wrinkle-free" programs. (The dryness level of the other programs cannot be adjusted.) ^ Press the selection button until the desired indicator illuminates.
6. Start the program ^ Press the "Start/Stop" button. Once the program starts, the current cycle of the program will be indicated in the "STATUS" display. 7. At the end of a program The "End/Anti-crease" indicator will light at the end of a program and the buzzer will sound if it was selected.
Canceling or changing a program ^ Press and release the "Start/Stop" button to stop the drying program. To continue drying: ^ Select the new program by pressing the e or - button. ^ Select any desired options. ^ Select a dryness level (available in the "Normal" and "Wrinkle-free" programs).
Child lock When activated, the child lock prevents the dryer from being operated by locking the control panel functions. The dryer can be turned on but not started. The "Child lock" indicator will flash. The door can be opened. To activate the child lock 1.
Cleaning the lint filter The lint filter must be cleaned after every program. ^ Open the door and remove the lint filter, 1 , by gently lifting it upwards. ^ Wipe the lint off the filter with your hand (do not use any sharp objects!) ^ Remove the lint from the door frame lint filter with your fingers.
The lint filters can be rinsed with hot water if necessary. ^ Take the door lint filters out by turning the knob at the filter top. ^ Rinse all lint filters with hot water and dry thoroughly. The filters must be dry before being returned to the dryer.
Emptying the condensed water container Depending on the installation, the condensed water will either be pumped to a drain or collected in the condensed water container, located in the upper left corner of the machine. The container holds approximately 1 gallon of water.
Cleaning the condenser , To reduce the risk of electric shock, disconnect the dryer from the power supply by shutting off the power main, tripping the circuit breaker or unplugging the power cord before performing maintenance. ^ Clean the condenser every 6 months and when the "Filter/Vent" indicator lights.
Rinsing the condenser ^ Rinse the condenser along the left side with warm water. ^ Rinse the condenser from the front with warm water. ^ Check the condenser for visible soiling. Rinse the condenser until clean. ^ Place the condenser lengthwise on a towel to air dry.
Quick Guide Remove this guide for easy reference Please read all instructions, especially the "Important Safety Instructions", before using the dryer.
1.Turn on the dryer and load the laundry ^ Press the "On/Off" button to turn on the dryer. ^ Press the "Door" button to open the door. ^ Load the laundry into the drum. Make sure that there is enough space in the drum for clothes to tumble freely.
4. Select the dryness level ^ Press the selection button until the desired indicator illuminates. 5. Select the buzzer (if desired) 6. Start the program ^ Press the "Start/Stop" button. 7. At the end of a program The "Anti-crease / End" indicator will light.
Program When to use Note Normal Available drying options T urbo, Gentle, Anti-crease Extra Dry For laundry to be folded and shelved immediately, e.g. jeans, towels. The "Extra Dry" program should not be selected for jersey materials. Items may shrink.
Changing the light bulb , To reduce the risk of electric shock, disconnect the dryer from the power supply by shutting off the power main, tripping the circuit breaker or unplugging the power cord before performing maintenance. ^ Open the door. The bulb cover is located along the upper rim of the drum opening.
What if the dryer will not run? Possible fault Solution The "Start/Stop" button was not pressed. Make sure the dryer is on. Press the "Start/ Stop" button to begin the drying program. The circuit breaker tripped or the dryer is unplugged.
What if the "Filter/Vent" fault indicator is lit? Possible fault Solution The lint filter is clogged. Clean the lint filters. See "Dryer care".
Repairs In the event of a fault which you cannot fix yourself, please contact Miele's Technical Service Dept. When contacting Technical Service, please quote the model and serial number of your appliance. They can be found on the data plate located below the drum opening.
Installation Instructions To prevent accidents and machine damage read these instructions before installation or use..
, WARNING - Risk of Fire ~ To reduce the risk of severe injury or death, follow all installation instructions. ~ Clothes dryer installation must be performed by a qualified installer. ~ Install the clothes dryer according to the manufacturer's instructions and local codes.
The tumble dryer can also be placed on top of a Miele washing machine for a stacked installation. An appropriate stacking kit is required. The stacking kit is available from your Miele dealer or the Miele Technical Service Department. , Installation of the stacking kit must be performed by a Miele authorized technician.
GROUNDING INSTRUCTIONS This appliance must be grounded. In the event of malfunction or breakdown, grounding will reduce the risk of electric shock by providing a path of least resistance for electric current. This appliance is equipped with a cord having an equipment grounding conductor and a grounding plug.
Front view a Power cord with plug b Condensed water container c Control panel d Door e Access panel to condenser f Four height adjustable feet g Optional drain hose: An alternative to using the condensed water container is to drain condensed water into a sink, standpipe or gully.
Rear view a Handle for transportation (arrows) b Air intake opening to cool the condenser c Power cord with plug d Condensate drain hose e Accessories for connection to a sink standpipe Installation site , Do not install the dryer in an area where it can be blocked, e.
Installation beneath a counter , When the machine lid needs to be removed to reduce the height of the machine, a built-under spacer kit * is necessary. It must be installed by a Miele Service Technician. The cover plate of the built-under kit replaces the appliance lid and ensures electrical safety.
Installation tips An airflow gap of 3 / 8 " (10 mm) must be provided between the machine and the floor. This airflow gap must not be blocked by a toe-kick or thick piled carpets. Sufficient venting of the installation site, e.g. by opening a window or door, is essential for the dryer's operation.
External water drain When drying is in progress, condensed water is pumped into the condensed water container through the drain hose at the back of the dryer. The condensed water can also be drained directly if the machine is installed near a sink or a standpipe so that the condensed water container does not have to be emptied.
Draining the condensed water into a sink ^ Secure the hose carefully, e.g. by tying the hose to the water tap, to avoid damage by overflowing water. ^ Use the curved guide to prevent the drain hose from becoming kinked (see Front view illustration). Connection to a standpipe ^ Insert the drain hose into the Y-adapter of the sink.
Installation requirements demanding a non-return valve , To prevent water from flowing back into the machine a non-return valve must be installed at the following installations: – Installation to a sink standpipe – Several installation possibilities where additionally another washer or dishwasher is connected to.
1 Connector 2 Sink connecting nut 3 Hose clamp 4 Hose end 5 Non-return valve 6 Dryer drain hose ^ Install the connector 1 with the sink connecting nut 2 to the sink standpipe. Usually the sink connection nut is equipped with a washer. Please remove the washer.
Disposal of the packing materials The packing materials protect the appliance during shipping. They have been designed to be biodegradable and recyclable. To prevent suffocation, ensure that any plastic wrappings, bags, etc. are disposed of safely and kept out of the reach of children.
All rights reserved / 2812 INFORMATION IS SUBJECT TO CHANGE. PLEASE REFER TO OUR WEBSITE TO OBTAIN THE MOST CURRENT PRODUCT SPECIFICATIONS, TECHNICAL & WARRANTY INFORMATION.
デバイスMiele T 8023 Cの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Miele T 8023 Cをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはMiele T 8023 Cの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Miele T 8023 Cの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Miele T 8023 Cで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Miele T 8023 Cを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はMiele T 8023 Cの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Miele T 8023 Cに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちMiele T 8023 Cデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
