MieleメーカーT7944Cの使用説明書/サービス説明書
ページ先へ移動 of 64
Operating instructions for condenser tumble dryer T 7944 C To avoid the risk of accidents or damage to the appliance it is essential to read these instructions before it is installed and used for the first time.
Disposal of the packing material The transport and protective packing has been selected from materials which are environmentally friendly for disposal and should be recycled. Ensure that any plastic wrappings, bags, etc are disposed of safely and kept out of the reach of babies and young children.
Caring for the environment ..........................................2 Warning and Safety instructions .....................................6 Operating the tumble dryer .........................................1 4 Control panel .......................
Cleaning and care ................................................2 6 Emptying the condensed water container ...............................2 6 Cleaning the fluff filters .............................................2 7 Cleaning them whilst dry ......
External condensed water outlet ......................................4 4 Arranging the drain hose .........................................4 4 External drainage via a sink or gully ................................4 5 Installation conditions requiring a non-return valve .
~ It is essential to read these instructions. This tumble dryer conforms to current safety requirements. Inappropriate use can, however, lead to personal injury and damage to property. To avoid the risk of accidents and damage to the tumble dryer, please read these instructions carefully before using it for the first time.
~ The tumble dryer can only be used by people with reduced physical, sensory or mental capabilities, or lack of experience or knowledge, if they are are supervised whilst using it or have been shown how to use it in a safe way and understand the hazards involved.
Technical safety ~ Before setting up the tumble dryer, check it for any externally visible damage. Do not install or use a damaged tumble dryer. ~ Before connecting the tumble dryer, ensure that the connection data on the data plate (voltage and frequency) match the mains electricity supply.
~ Faulty components must only be replaced by genuine Miele original spare parts. Only when these parts are fitted can the safety standards of the tumble dryer be guaranteed. ~ The tumble dryer must be isolated from the electricity supply in the event of a fault and during cleaning and maintenance.
Correct use ~ To prevent the risk of fire, the following textiles must not be dried in this appliance: – items which have not been washed. – items, such as workwear, which have not been thoroughly cleaned and which are still soiled with grease, oil or other deposits (such as cosmetics, lotions etc).
~ Danger. This tumble dryer must not be connected to a controllable socket (e.g. a timer switch or a peak load shut-off device). If the dryer programme were to be interrupted before the end of the cooling down phase, the laundry could self-combust.
~ The dryer must not be used without the fluff filters in place or if the fluff filters are damaged in any way. ~ The fluff filters must be cleaned regularly. ~ The dryer must not be used without the condenser unit in place. ~ The fluff filters must be thoroughly dried after cleaning.
Accessories ~ Only use genuine Miele original spare parts and accessories with this tumble dryer. If non-Miele parts are used, guarantee, performance and product liability claims may be invalidated. Miele cannot be held liable for damage caused by non-compliance with these Warning and Safety instructions.
Control panel a Perfect Dry indicator For all drying level programmes. See next page. b Display See next page. c Delay start button This button is used for: - Delaying the start of a programme - Selecting the duration of the timed drying Warm air and Cool air programmes d Buzzer button An audible tone sounds at the end of the programme.
The display shows: – Programme duration – Programme stage Drying Cooling down Finish – Check and fault messages The following are also selected via the display: – Duration of the Warm air and Cool air programmes – Delay start You can select a programme and set it to start at a later time.
Garment care label symbols Drying q Normal/higher temperature r Reduced temperature: Select Low temperature (for delicate textiles) s Do not tumble dry Ironing I Very hot H Hot G Warm J Do not iron Tips on drying – Always observe the maximum recommended loads given in the "Programme chart".
Brief instructions The headings numbered ( A , B , C ...) show the operating sequence and can be used as a brief guide to using your dryer. A Sort the laundry To ensure an even drying result sort laundry according to: . . . the drying level required .
D Select a programme ^ Select the programme you want. The indicator for the programme selected will light up. A drying level or extra option indicator may also light up and the duration may also be displayed.
F Start the programme The Start/Stop button will flash when a programme is being selected. The flashing indicates that a programme can be started. ^ Press the Start/Stop button. The Start/Stop button will now light up constantly. The Perfect Dry indicator will flash or light up constantly with the sensor controlled drying programmes.
Extra options Low temperature Delicate and minimum iron fabrics with the r symbol on the care label (e.g. acrylic garments) are dried at a lower temperature. The programme duration is longer. On some programmes Low temperature is permanently activated and so cannot be deselected.
Cottons Max. load 7 kg* Extra dry, Normal** Use for Single and multi-layered cotton fabrics such as towelling, T-shirts, underwear, flannelette bed linen. Notes – Select Extra dry for multi-layered and very thick fabrics. – Do not use Extra dry for loopknit fabrics (e.
Woollens handcare Max. load 2 kg* Use for Woollen items. Notes – This programme only fluffs up woollen garments. They are not dried completely by this programme. – Remove garments as soon as the programme has finished and leave to finish drying at room temperature.
Cool air Max. load 7 kg* Use for Any item which only needs airing. Warm air Max. load 7 kg* Use for – Drying voluminous and multi-layered fabrics whose layers have different drying characteristics, e.g. jackets, pillows. – Drying individual items, e.
Once a programme has started - changing the programme You cannot change to another programme once a programme has started (this prevents unintentional alterations). You will need to cancel the current programme before you can select a new one. - cancelling the programme and then selecting a different programme ^ Press the Start/Stop button.
The system lock prevents the dryer being used without your knowledge. It can be activated if wished. The dryer's electronics are then locked. The dryer can still be switched on but a programme cannot be started.
Emptying the condensed water container The condensed water will be collected in the condensed water container unless the appliance has been fitted with a drain hose (see "Installation"). Empty the condensed water container after every drying programme.
Cleaning the fluff filters The fluff which is created by the drying process is collected by the fluff filters in the door and the door opening. Clean the filters after each drying programme*. Cleaning them whilst dry Tip: You can also use a vacuum cleaner to remove the fluff.
Cleaning them with water If there is a great deal of compacted fluff on any of the filters, they can be removed and cleaned under hot running water. ^ Open the door and pull the fluff filter out of the door as described previously. The two filters in the door opening can also be removed if you need to clean them with water.
Cleaning the tumble dryer Disconnect the tumble dryer from the mains electricity supply. Miele branded cleaning and conditioning products are available to order via the internet on www.miele-shop.com. ^ Clean the housing and control panel with a slightly damp cloth and a mild detergent or soapy water.
Cleaning the condenser unit Detergent residue, hair and fine fluff from the dryer can get through the fluff filters and block the condenser unit. Dust from the room in which the dryer is installed can also get into the condenser unit and cause a blockage.
^ Pull the condenser unit out of its housing by the handle. Checking the condenser unit ^ Hold the condenser unit up to the light as shown . ^ Check to see if there is any fluff inside it. The arrows in the illustration above indicate where to look. If you cannot see any fluff: ^ Replace the condenser unit (see following page).
^ Then flush the unit through from the front. ^ Check the condenser unit again for any visible fluff and if necessary flush it through again until it has all gone. ^ Repeat as required. ^ Also make sure the rubber seals are clean. The rubber seals must not be removed and must be free of kinks.
With the help of the following notes minor faults in the performance of the appliance, some of which may result from incorrect operation, can be put right without contacting the Service Department.
Problem Possible cause Remedy The Clean out airways indicator light comes on. The dryer is not working efficiently or economically. Possible cause: the filters are clogged with fluff or with detergent residues. – Cleaning the filters is usually all that is required.
Problem Possible cause Remedy The Start/Stop button is flashing slowly and the display is dark. The dryer is in Standby mode. This is quite normal and not indicative of any fault. See "Programmable functions". Sometimes a programme cannot be started and the corresponding programme indicator light does not light up.
An unsatisfactory drying result Problem Possible cause Remedy The laundry is not sufficiently dry. The load consisted of different fabrics. – Finish drying using the Warm air programme. – Select a different programme next time *. Items made of synthetic fibres are charged with static electricity after drying.
Other problems Problem Possible cause Remedy The drying process goes on too long or even switches off. In some circumstances, the Clean out airways indicator light still comes on, even though the filters are clean. Please check all the possible causes and switch the dryer off and then back on again.
Problem Possible cause Remedy Water leaks from the dryer after the condenser unit has been cleaned. – The inner cover of the condenser unit has not been locked properly and/or the condenser unit has not been positioned correctly. – Fluff has collected in the condenser unit housing.
Changing the lamp Disconnect the tumble dryer from the mains electricity supply. ^ Open the door. You will find the interior light cover at the top of the drum aperture. ^ Insert a suitable tool, such as a wide bladed screwdriver, under the side edge of the light cover as illustrated.
Repairs In the event of any faults which you cannot remedy yourself, please contact – your Miele dealer or – the Miele Service Department (see back cover for contact details). When contacting your dealer or the Service Department, please quote the model and serial number of your appliance, both of which are shown on the data plate.
Front view a Mains connection cable b Control panel c Condensed water container d Door e Service panel for condenser unit f Four height adjustable screw feet g Air inlet and outlet vent for cooling the condenser unit h External drainage options (e.
Rear view a Protruding lid for holding when moving the machine (see arrows) b Air inlet vent for cooling the condenser unit c Mains connection cable d External drainage of the condensed water e Accessories for connection to a sink drain outlet Installation site , The machine lid must not be removed.
Levelling the machine The machine must be perfectly level to ensure safe and proper operation. ^ The screw feet can be adjusted to compensate for any unevenness in the floor. , The air inlet and outlet vents on the front and back of the machine must not be covered as this would prevent sufficient ventilation for cooling the condenser unit.
External condensed water outlet General notes When drying is in progress, condensed water is pumped into the condensed water container through the drain hose at the back of the dryer. The condensed water can also be drained off directly if the tumble dryer is installed near a sink, drain outlet etc.
External drainage via a sink or gully ^ See "Front view" illustration. , If you want to drain the water off into a sink you will need to secure the hose carefully, e.g. by tying it to a tap to make sure it cannot slip during use. Otherwise there is a risk of overflowing water which could cause damage.
1 Adapter 2 Nut 3 Hose clip 4 End of the hose 5 Non-return valve 6 Tumble dryer drain hose ^ Fit adapter 1 to the sink drain outlet using nut 2 . If this nut has a flat disc in it you should take the disc out first. ^ Attach the end of hose 4 to adapter 1 .
Electrical connection U.K. All electrical work should be carried out by a suitably qualified and competent person, in strict accordance with current national and local safety regulations (BS 7671 in the UK). Ensure power is not supplied to the appliance until after installation work has been carried out.
Load 1 Final spin speed in a domestic washing machine Residual moisture Energy Duration kg rpm % kWh min. Cottons Normal 2 7.0 3.5 1000 1000 60 60 4.14 2.28 109 65 Cottons Normal 7.0 7.0 7.0 7.0 1200 1400 1600 1800 53 50 44 43 3.75 3.55 3.15 3.10 100 95 86 84 Cottons Normal + Low temperature 7.
Height 850 mm Width 595 mm Depth 634 mm Depth with door open 1074 mm Suitable for pushing under a worktop – Height – Width Yes 850 mm 600 mm Suitable for stacking Yes Weight 52 kg Drum volume 111 l Maximum capacity 7 kg dry weight Capacity of condensed water container approx.
Altering the residual moisture level in the Cottons programme The tumble dryer is designed to dry effectively using as little energy as possible. However, if you require the laundry to be drier or damper, you can reduce or increase the default residual moisture in the Cottons programme.
Altering the residual moisture level in the Minimum iron programme The tumble dryer is designed to dry effectively using as little energy as possible. However, if you require the laundry to be drier or damper, you can reduce or increase the default residual moisture in the Minimum iron programme.
Anti-crease Anti-crease helps prevent creasing, if laundry is not normally removed im - mediately after the end of a programme. The anti-crease function – is activated when the tumble dryer is delivered. You can shorten the duration of the anti-crease phase or deactivate it if wished.
Altering the volume of the buzzer The buzzer has two volumes. Follow the steps ( A , B , C ...) to programme and store in memory. Before you begin, ensure that: – The tumble dryer is switched off. – The door is closed. A Press the Start/Stop button and keep it pressed in whilst carrying out steps B - C .
Altering the standard drying level in the Automatic plus programme The tumble dryer is designed to dry effectively using as little energy as possible. However, if you require the laundry to be drier or damper, you can reduce or increase the default residual moisture in the Automatic plus programme.
Extending the cooling down time The cooling down phase which takes place before the end of a programme can be extended by 5 or 10 minutes, if required. This makes the garments easier to handle. The cooling down time can only be extended for programmes with drying levels.
Standby To save energy, the display and the programme sequence/check lights go out after 10 minutes and the Start/Stop button starts flashing slowly. To come out of standby mode ^ Turn the programme selector or press a button. Neither will have any effect if a programme is running.
Before you begin, ensure that: – The tumble dryer is switched off. – The door is closed. A Press the Start/Stop button and keep it pressed in whilst carrying out steps B - C . B Switch the dryer on. Wait until the Start/Stop button lights up constantly .
Memory function The electronics will memorise any extra options selected for a programme. The duration selected for the Warm air or Cool air timed drying programmes will also be stored in memory. These settings will be selected automatically the next time the programme is chosen.
Clean out airways indicator Fluff should be removed after drying. The Clean out airways indicator will remind you to clean the filters when a certain amount of fluff has collected in the filters. You can decide at what level of fluff this reminder should be given.
Keypad tone An audible tone sounds each time a button is pressed. Follow the steps ( A , B , C ...) to programme and store in memory. Before you begin, ensure that: – The tumble dryer is switched off. – The door is closed. A Press the Start/Stop button and keep it pressed in whilst carrying out steps B - C .
Adjusting the dryer's electronics for very soft water , In some areas of the UK, water is extremely soft which can affect the sensitivity of the control electronics. If the dryer is installed in an area of very soft water, you should contact your local water supplier for information and advice regarding water hardness and water conductivity.
Extending the range of the drying levels You can extend the range of the drying levels for many of the programmes: Machine iron+ (drier than Machine iron). Slightly dry (drier than Hand iron). Normal+ (drier than Normal). This programmable function is only available for programmes with drying levels.
63.
M.-Nr. 07 851 060 / 05 Alteration rights reserved/0113.
デバイスMiele T7944Cの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Miele T7944Cをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはMiele T7944Cの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Miele T7944Cの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Miele T7944Cで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Miele T7944Cを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はMiele T7944Cの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Miele T7944Cに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちMiele T7944Cデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
