Ariensメーカー921008 - ST927LETの使用説明書/サービス説明書
ページ先へ移動 of 42
Owner/Operator Man ual Models 921004 – S T924DLE 921005 – S T927LE 921006 – S T1 130DLE 921007 – S T924LE T 921008 – S T927LE T 921009 – S T1 130LET Sno-Thro ® 03389300 4/08 Printed in US.
GB - 2 SAFETY . . . . . . . . . . . . . . . . . . . . . . . . . 4 ASS EM BL Y . . . . . . . . . . . . . . . . . . . . . . . 8 CONTROLS and FEA TURES. . . . . . . . 13 OPERA TION . . . . . . . . . . . . . . . . . . . . . 16 MAINTENANCE . . . . . . . . .
GB - 3 • Record Unit M odel and Serial numbers here. • Record Engine Model and Serial numbers here. PRODUCT REGISTRATION The Ariens d ealer must register the product at the time of purchase. Registering the product will help the company process warranty claims or contact you with the latest service information.
GB - 4 SAFETY ALERT S Look for these s ymbols to point out important safety precautions. They mean: Attention! Personal Sa fety Is Invo lved! Become Alert! Obey T he Mes sage! The safety alert symbols above an d signal words below are used on decals and in this manual.
GB - 5 2. DANGER! 3. DANGER! SAFETY RULES Read, understand, and follow al l safety practices in Owner/Operator Manual before beginning assembly or operating. Failure to follow instructions could result in personal injury and/or d amage to unit. AL WA YS rem ove key and/or wire from spark plug before assembly , maintenance or service.
GB - 6 DO NOT operate near drop-offs, di tches, or embankments. Unit can s uddenly turn over if a wheel is over the edge of a cliff or ditch, or if an edge caves in. Falling snow , fog, etc. can reduce vision and cause an accident . Operate unit only when there is good visibility and light.
GB - 7 Check clutch and brake operation frequently . Adjust and service as required. All motion of drive wheels and auger/impeller must stop quickly when cont rol levers are released. DO NOT operate on steep slopes. DO NOT clear snow across the fa ce of slopes.
GB - 8 PACKAGE CONTENTS ASSEMBLY T ools Required: •P l i e r s • Open-End Wrenches: 3/8, 7/16, 1/2, 9/16 in. and/or Adjust able Wrench • Ti re Gauge Unfold Handleba r (Figure 5 ) 1. Rem ove the lower and loosen the upper wing knobs on the handlebar assembly .
GB - 9 Inst all D ischarg e Chut e and Discha rge Chu te Cran k (921004, 006, 007, 008, 009) (Figure 6) 1. Grease underside of discharge chute ring (if not already greased). 2. Remove mounting hardware from auger housing. 3. Install discharge chute over opening in the auger housing.
GB - 10 NOTE: After the chute r od has been inserted through the hex hole in the control assembly , placing the unit in the service position (see Service Posit ion on page 22) will ease alignment and installation of the hair pin.
GB - 11 4. Insert the short end of the chute rod into the hole in the front of the control panel. 5. Connect the chute crank to the pinion gear on chut e with spring clip. IMPORT ANT : Rotate the disc harge chute to the lef t when tightening the pedest al hardware to ens ure clearance between t he discharge chute and the belt cover.
GB - 12 Check T rack T ension (921007, 0 08, 009) Check tracking of unit and t ension of tracks (see T r ack T ension Adjustment ( 921007, 008, 009) on p age 34). Check Auger Ge arcas e Oil Check oil level in auger gearcase (see Check Auger Gearc ase on page 23).
GB - 13 1. Attachme nt Clutch Lever 2. Speed Selector 3. Traction Drive Clutch Lever 4. Chute Cont rol 5. Oil Fill/Dips tick 6. Disc harge Chute Deflector 7. Disc harge Chute 8. Impeller 9. Clean-Out T o ol 10. Auger 1 1. Scraper Blade 12. Aug er Gearcase 13.
GB - 14 1. Attachme nt Clutch Lever 2. Speed Selector 3. Deflector Remote Control 4. Chute Cont rol 5. Traction Drive Clutch Lever 6. Oil Fill/Dips tick 7. Disc harge Chute Deflector 8. Disc harge Chute 9. Impeller 10. Clean-O ut T ool 1 1. Aug er 12.
GB - 15 1. Attachme nt Clutch Lever 2. Speed Selector 3. Deflector Remote Control 4. Chute Cont rol 5. Traction Drive Clutch Lever 6. Oil Fill/Dips tick 7. Disc harge Chute Deflector 8. Disc harge Chute 9. Impeller 10. Clean-O ut T ool 1 1. Aug er 12.
GB - 16 CONTROLS AND FEA TURE S See CONTROLS and FEA T URES on page 13 for all Controls and Features locations. Dual Handle Interlock When Attachment Clutch and th en T raction Drive Clutch are engaged, the Attachment Clutch will remain engaged (leve r down) if released.
GB - 17 S peed Selecto r Position the Speed Selector in the appropriate speed notch to control forward and reverse t ravel. Forwar d: (6) Fast est (1) Slowest Reverse: (1) Slow (2) Fast IMPORT ANT : DO NOT change motion from forward to reverse with clutch engaged.
GB - 18 Discharge Chute Discharge chute rotates 200°. AL WA Y S position discharge chute in safe direction and angle, away from operator and bystanders, before starting engine.
GB - 19 T rack Angle (92 1007, 0 08, 00 9) (Figure 19) The track angle can be adjusted to position the auger housing for level clearing, deep cutting or transport. Squeeze the ha ndlebar trigger and press down on the handlebar s to move t he auger housing into an up positi on.
GB - 20 2. Check Function o f Clutches If clutches do not engage or disengage properly , adjust or repa ir before operation. See Attachment Clutch/Brak e Adjustment on page 28 and T racti on Drive Clutch Adjustmen t on p age 30. 3. Che ck Dual Ha ndle Inte rlock Without the engine running, pres s down (engage) both clutch levers.
GB - 21 4. Make sure that the traction clutch and attachment drive clutc h levers are fully disengaged. 5. Push Primer Bulb 2 or 3 times for cold engine. NOTE: When temperature is below -15° F (-26° C) additional priming may be needed. 6. Insert key into ignition switch on engine and push into "Run" posit ion.
GB - 22 Ariens Dealers will provide any service or adjustments which may be required to keep your unit operating at peak efficiency . Should engine service be required, contact an Ariens dealer or an auth orized engine manufacturer's service center .
GB - 23 If clutches do not engage or disengage properly , adjust or repa ir before operation. See Attachment Clutch/Brak e Adjustment on page 28 and T racti on Drive Clutch Adjustmen t on p age 30. CLE AN E N GINE Refer to Engine Manual f or detailed instructions.
GB - 24 GENERAL LUBRICATION IMPORT ANT : Wipe each fitting clean before and after lubrication. Do not wipe gea rcase filler plug; wiping the gearcase filler pl ug may remove thread sealant and cause leaks . IMPORT ANT : DO NOT allow grease or oil to get on friction disc, f riction plate or belt s.
GB - 25 SHEAR BOLTS IMPORT ANT : Use only Ariens shear b olts for replacement. Use of any other type of s hear bolt may result in severe damage to unit. See SERVICE P A RTS on page 35. Occasionally a foreign object may enter the auger/impeller housing and jam the auger , breaking shear bolts (Figure 25) which secure the aug er to the shaft.
GB - 26 4. T o adjust deflector higher: Slide cable up. Tighten top nut. 5. Check travel and repeat adjustment as necessary . DISCHARGE CHUTE (9 21004, 006, 007, 0 08, 009 ) If chute does not st ay in.
GB - 27 DISCHARGE CHUTE (9 21005) If discharge chute does not stay in position while operating, tighten nut on carriage bolt at pivot point to increase tension on spring (Figure 31). SPEE D SEL ECTOR ADJUSTMEN T T o adjust (Figure 32): 1. Disc onnect adjustment pivot pin from speed selector lever by removing hair pin.
GB - 28 ATT ACHMENT CLUTCH/BRAKE ADJUSTMENT (Figures 33, 34 and 35) Remove Att achment Cable Slack 1. Remove t he belt cover . 2. Loosen jam nut on cable adjustment barrel, and then turn the adjustment barrel up or down to lengthen or shorten cable and remove all cable slack.
GB - 29 Adjust th e Att achm ent Clutch Cable S pring Extension 1. Check the attachment clutch cable spring extension. Measure the length o f the attachment clutch cable spring with the clutch lever disengaged. Then measure the attachment clutch spring with the clutch lever engaged.
GB - 30 Check Attac hment Brake See Figure 38. 1. With the clutch lever disengaged, brake pad must contact a ttachment belts . With clutch lever engaged, brake pad must be more than 1/16 in. (1.6 m m) from belts. If there is more than 1/16 in. (1.6 mm ) gap, go to Check Belt Finger Clearance on page 30.
GB - 31 a. With the traction drive clutch lever disengaged, loosen the jam nut on the cable adjuster. b. Turn the adjuster body up the cable to decrease the distance between the clutch lever and handlebar . c. Turn the adjuster body dow n the cable to increase the distance between the clutch lever and handlebar .
GB - 32 8. Remove hex bolts securing housing to frame (two on each side). Tip housing and frame apart on pivot pin (Figure 43). 9. Remove attachment driv e belts from attachment pulley (hold brak e away from belt). Inst all ne w att ach ment dri ve belt s: 1.
GB - 33 2. T o gain belt clearance, remove swing gate spacer and slide drive plate over so that finger clears stop hole in f rame and can swing past it. See F igure 45. 3. Pull idler away from t raction drive belt and remove belt from idler pulley , engine sheave and driven pulley (it may be necessary to turn engine pulley using recoil handle).
GB - 34 T RACK T ENSION ADJ USTMENT (9210 07, 008, 00 9) Check the track tension by applying pressu re on the track mi dway between the uppe r and rear track rollers. Deflection should be approximately 3/8 in. (9. 6 mm). See Figure 47. If deflection is exces sive, tighten the track tension.
GB - 35 SHORT T ERM IMPORT ANT : NEVE R spray unit with high pressure wa ter or store unit outdoors . Run with attachment clutch engag ed a few minutes after each use to free unit of any loose or melting snow . Close fuel shut-off valve. Inspect unit for v isible signs of wear , breakage or damag e.
GB - 36 TROUBLESHOOTING PROBLEM PROBABLE CAUSE CORRECTION Engine wi ll not crank/ st art. 1. Fuel tank is empty . 2. Fuel shut-off valve closed. 3. Build up of dirt and residue around governor/carburetor . 4. Key Switch not in run position. 5. Electric starter not functioning.
GB - 37 SPECIFICA T IONS Model Num ber 921004 921005 921006 Description ST924DLE ST927LE ST1 130DLE Engine - T ecumse h LH318SA Te c u m s e h LH318SA Te c u m s e h LH358SA Pow er Max - HP (kW) 9.0 (6.71) 1 1.0 (8.20) Fast Idle S peed - RPM (min) 3600 ± 150 Displacement - in.
GB - 38 SPECIFICA T IONS Model Num ber 921007 921008 921009 Description ST924LET ST927LET ST 1 1 30LET Engine - T ecums eh LH318SA Te c u m s e h LH358SA Pow er Max - HP (kW) 9.0 (6.71) 9.0 (6.71) 1 1.0 (8.20) Fast Idle S peed - RPM (min) 3600 ± 150 Displacement - in.
ARIENS COMP ANY GRA VEL Y ® | STENS ® | LOCKE ® | NA TIONAL ® | BYNORM ® | EVERRIDE ® | GREA T DANE ® Snow_200 8 39 of 40 Three-Y ear Lim i ted Sno-Thro ® Wa r r a n t y Ariens Company (Ariens.
ARIENS COMP ANY GRA VEL Y ® | STENS ® | LOCKE ® | NA TIONAL ® | BYNORM ® | EVERRIDE ® | GREA T DANE ® Snow_200 8 40 of 40 Limitations • Batteries are war ranted only f or a pe riod of 12 m onths after dat e of pur chase, on a p rorated b asis.
.
Ariens Company 655 West Ryan St reet Brillion, W I 541 10-1 072 920-756-2141 Fax 920-756-2407 www . ariens.com.
デバイスAriens 921008 - ST927LETの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Ariens 921008 - ST927LETをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはAriens 921008 - ST927LETの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Ariens 921008 - ST927LETの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Ariens 921008 - ST927LETで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Ariens 921008 - ST927LETを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はAriens 921008 - ST927LETの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Ariens 921008 - ST927LETに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちAriens 921008 - ST927LETデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
