Mitsubishi ElectronicsメーカーEX200Uの使用説明書/サービス説明書
ページ先へ移動 of 49
ENGLISH DLP™ PROJECT OR MODEL EX200U/ES200U User Manual EX200U/ES200U This User Manual is important to you. Please read it before usin g your projec tor .
EN-2 The lightning flash with arrowhea d symbol within an equilateral tria ngle is intended to aler t the user to the presence of unins u- lated "dangerous voltage" wi thin the product ’s encl osure that may be of sufficient magnitude to constitute a risk of electric shock.
EN-3 ENGLISH WA R N I N G • The lens cap is for protecting the lens. If you leave th e l ens cap on the lens with the projector turned on , it may be deformed because of heat build-up. Remove the lens cap when you tu rn on the projector . • One of power cor ds f or th e U.
EN-4 Content s Important safeguards ......... ............ ........... ............. ........... ........... .............. ........... ............. .. ....... ........... 5 Projecto r exterior view ............. ........... ........... ............ .
EN-5 ENGLISH Import ant safeguards Please read all these instructions regarding your projector and retain them for future reference. Fol low all warnings and instructions marked on the projecto r . 1. Read instructions All the safety and operating instr uctions should be read before the appliance is operated.
EN-6 WA R N I N G : Unplug immediately if there is something wrong with your projector . Do not operate if smoke, stra nge noise or odor comes out of your pro- jector . It may cause fire or electric shock. In this case, unplug immedi - ately and contact yo ur dealer .
EN-7 ENGLISH Projector exterior view 1. External control panel (See "Projector" on page 8 for details.) 2. Lamp cover 3. V ent (heated air exhaust) 4. Quick-release button 5. Lens cover 6. Focus ring and Zoom ring 7. Front IR remote sensor 8.
EN-8 Controls and functions Pr ojector 1. Focus ring Adjusts the focus of the pro jected imag e. See "Fine- tuning the image size and clarity" on page 23 for details. 2. Zoom ring Adjusts the size of the image. See "Fine-tuning the image size and clarity" on page 23 for details.
EN-9 ENGLISH Remote control 1. POWER T oggles the projector between standby mode and on. See "Star ting up the projector" on page 19 and "Shutting down the projector" on page 31 for details. 2. FREEZE Freezes the projected i mage. See "Freezing the image" on page 30 for details.
EN-10 Remote control effective range Infra-Red (IR) remote control sensor is located on the front of the pr ojector . The remote control must be held at an angle within 30 degrees perpendicular to the projector's IR remote control sensor to function correctly .
EN-11 ENGLISH Positioning your projector Choosing a location Y our room layout or personal preference will dictate which installation location you select.
EN-12 Thus, a 16:9 aspect image will not utili ze 25% of the height of a 4:3 aspect im age display ed by this projector . This will be seen as darkened (unlit) bars along the top and bottom (vertical 12.
EN-13 ENGLISH Layout of the pr ojector Image size varie s de pending on the distance between the screen and the projector . Front pr ojection (Standar d) (16:9) The above figures are approximate and may be slightly diffe re nt from the actual measurement s.
EN-14 Connection When connecting a signal source to the projector , be sure to: 1. T urn all equipment off before making any connections. 2. Use the correct signal cables for each source. 3. Ensure the cables are firmly inserted. • See the owner ’ s guide of each device for details about it s connections.
EN-15 ENGLISH Connecting a monitor If you want to view your presentation close-up on a monitor as well as on the screen, you can connect the MONITOR OUT signal output jack on the projector to an external monitor following the instructions below: T o connect the projector to a monitor: 1.
EN-16 Connecting a Component V ideo source device Examine your V ideo source device to determine if it has a set of unused Component V ideo output sockets available: • If so, you can continue with this p rocedure. • If not, you will need to reassess which method you can use to connect to the device.
EN-17 ENGLISH Connecting an S-V ideo source device Examine your V ideo source device to determine if it has an unused S-V ideo output socket available: • If so, you can continue with this procedure. • If not, you will need to reassess which method you can use to connect to the device.
EN-18 Connecting a composite V i deo sour ce device Examine your V ideo source device to determine if it has a set of unused composite V ideo output sockets available: • If so, you can continue with this p rocedure. • If not, you will need to reassess which method you can use to connect to the device.
EN-19 ENGLISH Operation S tarting up the pr ojector 1. Plug the power cord into the projector and into a wall socket. Turn on the wall socket switch (where fitted). Check that the POWER indicator light on the projector lights orange after power has been applied.
EN-20 Using the menus The projector is equipped with On-Screen Display (OSD) menus for making various adjustments and settings. Below is the overvie w of the OSD menu. Below is an example about how to set the OSD language. 1. Press MENU/EXIT on the projector or remote control to turn the OSD menu on.
EN-21 ENGLISH Utilizing the password function For security purposes and to help prevent unauthorized use, the projector includes an option for setting up password security . The password can be set through the On-Screen Display (OSD) menu. For details of the OSD menu operation, please refer to "Using the menus" on page 20 .
EN-22 Password: __ __ __ __ __ __ Keep this number i n a safe place. 5. Confirm the new password by re-entering the new password. 6. Y ou have successfully assigned a new password to the projector . Remember to enter the new password next time the projector is started.
EN-23 ENGLISH Adjusting the projected image Adjusting the projection angle The projector is equipped with 1 quick- release adjuster foot and 1 rear adjuster foot. These adjusters change the image height and projection angle. T o adjust the projector: 1.
EN-24 Corr ecting keystone Keystoning refers to the situation where the projected image is noticeably wider at either the top or bottom. It occurs when the projector is not perpendicular to the screen. T o correct this, besides adjusting the height of the projector , you will need to manually correct it following one of these ste ps.
EN-25 ENGLISH Selecting the aspect ratio The 'aspect ratio' is the ratio of the image width to the image height. Most analog TV and computers are in 4:3 ratio, which is the default for this projecto r , and digital TV and DVDs are usually in 16:9 ratio.
EN-26 Optimizing the image Selecting a pictur e mode The projector is preset with several predefined picture modes so that you can choose one to suit your operating en vironment and input signal picture type. T o select a operation mode that suits your need, you can follow one of the following steps.
EN-27 ENGLISH Fine-tuning the image quality in user modes According to the detected signal type, there are some user -definable functions available when User 1 or User 2 mode is selected. Y ou can make adjustments to these functions based on your needs.
EN-28 3D Color Management In most installation situations, color management will not be necessary , such as in classroom, meeting room, or lounge room situations where lights remain on, or where buildin g external windows allow daylight into the room.
EN-29 ENGLISH Setting the pr esentation timer The presentation timer can indicate the presentation time on the screen to help you achieve better time management when giving presentations.
EN-30 Hiding the image In order to draw the audience's full attention to the presenter, you can use BLANK on the projector or remote control to hide the screen image. Press any key on the projector or remote control to restore the image. The word ' BLANK ' appears at the lower right corner of the screen while the imag e is hidden.
EN-31 ENGLISH 1. Repeat steps 1-2 above. 2. Press to highlight Volume and press / to select a desired sound level. Personalizing the pr ojector menu display The On-Screen Display (OSD) menus can be set according to your preferences. The following settings do not affect the projection settings, operation, or performance.
EN-32 Menu operation Menu system Please note that the on-screen display (OSD) menus vary according to the signal type selected. Main menu Sub-menu Options 1. DISPLAY Wall Screen Off/Light Yellow/Pink/Light Green/Blue/ Blackboard Aspect Ratio A uto/Real/4:3/16:9 Keystone Position Phase H.
EN-33 ENGLISH Note that the menu items are available when the projector detects at least one valid signal. If there is no equipment connected to the projector or no signal detected, limited menu items are accessible.
EN-34 Description of each menu FUNCTION DESCRIPTION Wall Screen Corrects the projected picture’ s color w hen the projection surface is not white. See "Using W all Screen" on page 28 for details. Aspect Ratio There are four options to set the image's aspect ratio depending on your input signal source.
EN-35 ENGLISH FUNCTION DESCRIPTION Setting Pre-defined picture modes are provided so you can optimize your projector image set-up to suit your program type. S ee "Selecting a picture mode" on page 26 for details. Brightness Adjusts the brightness of the image.
EN-36 FUNCTION DESCRIPTION Presentation T imer Reminds the presenter to finish the presentation within a certain time frame. See "Setting the presentation timer" on page 29 for details. Language Sets the languag e for the On-Screen Display (OSD) menus.
EN-37 ENGLISH FUNCTION DESCRIPTION Security Settin gs Change password Y ou will be asked to ente r the current password b efore changing to a new one. Power on lock See "Utilizing the password function" on page 21 for details.
EN-38 Maintenance Car e of the projector Y our projector needs little maintenance. The only thing you need to do on a regular basis is to keep the lens clean. Never remove any parts of the projector except the lamp. Contact your dealer if other par ts need replacing.
EN-39 ENGLISH Lamp information Getting to know the lamp hour When the projector is in operation, the duration (in hours) of lamp usage is automatically calculated by the built-in timer .
EN-40 Timing of r eplacing the lamp When the lamp indicator lights up red or a message appears suggesting it is time to replace the lamp, please install a new lamp or consult your dealer . An old lamp may cause a malfunction in the projector and in some instances the lamp may explode.
EN-41 ENGLISH Replacing the lamp Spare lamp for EX200U/ES200U: VL T -EX 240L P • Be sure to replace the lamp with a new lamp sep arately sold that is exclusive to this projec tor .
EN-42 13. Restart the projector . Do not t urn the p ower on with the l amp cove r removed. Resetting the lamp timer 14. After the startup logo, open the On-Screen Display (OSD) menu. Go to the SYSTEM SET UP : Ad van ced > Lamp Settings menu. Press MODE/ENTER .
EN-43 ENGLISH • Do not reset if the lamp is not new or replaced as this could cause damage. • This projector uses a lamp that cont ains mercury . Disposal of the lamp or the projector with the lamp may be regulated due to environment al considerations.
EN-44 Indicators Light St atus & Description Power Te m p Lamp Power events Orange Off Off Stand-by mode Green Flashing Off Off Powering up Green Off Off Normal operation Orange Flashing Off Red • The projector needs 90 seconds to cool down as it was abnormally shut down without the normal cooling down process.
EN-45 ENGLISH T roubleshooting The projector does not turn on. No picture Blurred image Remote control does not work The password is incorrect Cause Remedy There is no power from the power cable. Plug the power cord into the AC inlet on the projector, and plug the power cord into the power outlet.
EN-46 Specifications Pr ojector specifications All specifications are subject to change without notice. General Product name DLP™ Projector Model name EX200U ES200U Optical Resolution 1024 x 768 XGA 800 x 600 SVGA Display system 1-CHIP DMD Lens F/Number F = 2.
EN-47 ENGLISH Dimensions 282 mm (W) x 94 mm (H ) x 229 mm (D) (Not including protrusion) T iming chart Supported timing for PC input * The projector only supports the timi ng (720 x 400) with 5 lines (R, G , B, H, V).
EN-48 Supported timing for Component-YP b P r input Displaying a 1080i(1 125i)@60Hz or 1080i(1 125i)@50Hz signal may result in slight image vibration. Supported timing for V id eo and S-V ideo inputs What’ s included in the box Replacement part Signal Format Horizontal Frequency (kHz) V ertical Frequency (Hz) 480i(525i)@60Hz 15.
EN-44 Mitsubishi Projector W arranty , Sales Suppor t and Ser vice Inf ormation North Amer ica MDEA (Mitsubishi Digital Electronics America, Inc.) Presentation Products Division 9351 Jeronimo Road Irvine CA 92618, USA For Warranty Registration, visit: http://www .
デバイスMitsubishi Electronics EX200Uの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Mitsubishi Electronics EX200Uをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはMitsubishi Electronics EX200Uの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Mitsubishi Electronics EX200Uの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Mitsubishi Electronics EX200Uで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Mitsubishi Electronics EX200Uを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はMitsubishi Electronics EX200Uの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Mitsubishi Electronics EX200Uに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちMitsubishi Electronics EX200Uデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
