Mitsubishi ElectronicsメーカーHC1500の使用説明書/サービス説明書
ページ先へ移動 of 39
HC1500 DLP™ PROJECTOR MODEL HC1500 User Manual This User Manual is important to you. Please r ead it befor e using your pr ojector ..
EN-2 CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK) NO USER-SERVICEABLE P ARTS INSIDE REFER SERVICING TO QUALIFIED SER VICE PERSONNEL.
EN-3 Contents Declaration of Conformity Model number: HC1500 T rade name: MITSUBISHI ELECTRIC Responsible party: Mitsubishi Digital Electronics America, Inc. 9351 Jeronimo Road, Irvine, CA 92618 U.S.A T elephone number: +1-(949) 465-6000 This device complies with Part 15 of the FCC Rules.
EN-4 Important safeguar ds Please read all these instructions r egar ding your projector and r etain them for futur e refer ence. Follow all warnings and instructions marked on the projector . 1. Read instructions All the safety and operating instructions should be read befor e the appliance is operated.
EN-5 Important safeguar ds (continued) WARNING: Unplug immediately if there is something wr ong with your projector . Do not operate if smoke, strange noise or odor comes out of your projector . It might cause fi re or electric shock. In this case, unplug immediately and contact your dealer .
EN-6 Pr eparing your pr ojector Cables Power supply parts RGB cable for PC (246C521-10) Mini D-SUB 15-pin Mini D-SUB 15-pin D-SUB 9-pin 8-pin RS-232C cable (246C508-10) • Used for projector contr ol by computer .
EN-7 Pr eparing your pr ojector (continued) Overview 3 2 1 57 10 9 8 6 4 2 1 3 4 8 5 6 7 9 1 FOCUS ring 2 ZOOM ring 3 Control panel 4 Air outlet grille 5 Remote contr ol sensor (Front) 6 Air inlet gri.
EN-8 COMPUTER COMPONENT HDMI PC COMP CONTRAST ASPECT CNT M1 AV MEMOR Y BRIGHTNESS BRT M2 COLOR TEMP C. T . GAMMA SHARPNESS SHARP AUTO POSITION A.P . KEYSTONE BLANK KS M3 VIDEO S-VIDEO ENTER MENU 1 2 3.
EN-9 30° 30° 30° 30° Using the r emote control 20° 10° 20° 10° 20° 20° 20° 20° Operational range of the r emote contr ol • Keep the remote contr ol photo-sensor out of direct sunlight or fl uor escent lamp light. • Keep the remote contr ol photo-sensor at least 2 m (6 feet) away from fl uorescent lamps.
EN-10 Setting up your pr ojector W A A=B B Setting up the screen Install the screen perpendicularly to the pr ojector . If the screen can not be installed in such a way , adjust the projection angle of the pr ojector .
EN-11 Setting up your pr ojector (continued) Front pr ojection, ceiling mounting For ceiling mounting, you need the ceiling mount kit designed for this projector .
EN-12 Scr een size and pr ojection distance Refer to the following table to determine the screen size. B A Hd 40 102 19.6 50 34.9 89 56 1.4 68 1.7 6.6 17 60 152 29.4 75 52.3 133 85 2.2 103 2.6 9.9 25 80 203 39.2 100 69.7 177 114 2.9 139 3.5 13.2 33 100 254 49.
EN-13 Viewing video images A. Connecting the pr ojector to video equipment • When the pr ojector and the connected devices are located too close to each other , the projected image may be af- fected by their interference. • See the owner’ s guide of each device for details about its connections.
EN-14 HDMI IN USB SERIAL TRIGGER COMPONENT VIDEO IN S-VIDEO IN VIDEO IN P B /C B Y P R /C R P B /C B Y P R /C R 1 2 COMPONENT VIDEO IN S-VIDEO IN VIDEO IN 1 2 COMPONENT VIDEO IN S-VIDEO IN VIDEO IN Connecting to a video player , etc. 1. Connect one end of the optional video cable to the VIDEO IN terminal of the projector .
EN-15 Connecting to video equipment having a HDMI terminal or DVI-D terminal Y ou can project high-quality images by connecting the HDMI IN terminal of this projector to video equipment having a HDMI output terminal or a DVI-D output terminal.
EN-16 When you connect this projector and a DVI-Digital device (such as a DVD player) via the HDMI terminal or DVI-D (HDCP) terminal, black color may appear dark and deep, depending on the type of the connected device. • This depends on the black level setting of the connected device.
EN-17 C. Pr ojecting images Preparation: • Remove the lens cap. • T urn on the power of the connected video equipment. 1. Confi rm the POWER indicator lights-up r ed.
EN-18 T o stop projecting: 8. Press the POWER button on the projector or the OFF ( ) button on the remote contr ol. • A confi rmation message is displayed. • T o cancel the procedure, leave the pr ojector for a while or press the MENU button. 9. Press the POWER button on the projector or the OFF ( ) button on the remote contr ol again.
EN-19 Sub Title Sub Title Sub Title Sub Title Sub Title Sub Title Sub Title Setting the aspect ratio Y ou can change the aspect ratio of the input video signal (or the ratio of width to height of the image). Change the setting according to the type of the input video signal.
EN-20 2 1 HDMI IN USB SERIAL TRIGGER COMPONENT VIDEO IN S-VIDEO IN VIDEO IN HDMI IN USB SERIAL TRIGGER COMPONENT VIDEO IN S-VIDEO IN VIDEO IN 2 1 Viewing computer images A. Connecting the projector to a computer Preparation: • Make sure that the power of the pr ojector and that of the computer are turned off.
EN-21 POWER ST A TUS C. Projecting images Preparation: • Remove the lens cap. • T urn on the power of the connected computer . 1. Confi rm the POWER indicator lights-up r ed.
EN-22 BLANK mode The video signal is temporarily muted when the BLANK button is pressed. T o cancel muting, press the BLANK button again. • It takes several seconds to disable the BLANK mode. AUTO POSITION button When the image supplied from the computer is displaced, carry out the following pr ocedure.
EN-23 Menu operation • Menus are not displayed when no signal is supplied to the pr ojector . * 1: Not available with certain signals. * 2: Available only when the input signal is TV50, TV60, 480i, or 576i. * 3: Available only when the input signal is from the VIDEO IN or S-VIDEO IN terminal.
EN-24 How to set the menus: The following describes how to set AUTO POWER OFF time as an example. 1. Press the MENU button. • When no signal is applied, the menu would not appear . 2. Press the or button to select a menu to use. 3. Press the ENTER button (or button).
EN-25 2. INST ALLA TION menu ITEM SETTING FUNCTION LAMP MODE ST ANDARD Select this option when you want to view images in a well-lit r oom. LOW Select to moderate the intensity of the lamp. The fan operating sound is reduced and the lamp lifetime becomes longer .
EN-26 4. SIGNAL menu 5. USER menu Menu operation (continued) 4. SIGNAL menu ITEM SETTING FUNCTION HORIZ. POSITION 0 - 999 * Use to adjust the horizontal position of the projected image. VERT . POSITION 0 - 999 * Use to adjust the vertical position of the projected image.
EN-27 Adjusting pr ojected images T o adjust the brightness (CONTRAST and BRIGHTNESS): Y ou can make adjustments for the brightness of the projected image using the menu. (See page 24 for menu setting.) 1. Display the IMAGE menu. 2. Select CONTRAST or BRIGHTNESS by pressing the or button.
EN-28 T o adjust the tone of white (COLOR TEMP .): Y ou can select a preset color temperature (white tone) using the menu. (See page 24 for menu setting.) 1. Display the IMAGE menu. 2. Select COLOR TEMP . by pressing the or button. 3. Select your desired color temperature by pr essing the or button.
EN-29 This projector automatically and pr operly projects video signals supplied from the computer . However , some video signals may not be projected, depending on the type of the computer . In such a case, press the AUTO POSITION button. (See page 22.
EN-30 DISPLA Y INPUT LOCK UNLOCK OK OK P ASSWORD CONFIRM O K CANCEL DISPLA Y INPUT LOCK UNLOCK OK OK P ASSWORD O K CANCEL Password function This projector is equipped with the passwor d function that is designed for prevention of theft and wr ong op- eration by children and r estriction on operation by other than specifi ed users.
EN-31 This projector is equipped with a lamp to pr oject images. This lamp is a consumable. It may bur n out or its brightness may decrease during use. In such cases, r eplace the lamp with a new one as soon as possible. Be sure to replace the lamp with a new lamp sold separately that is exclusive to this projector .
EN-32 (c) (a) (b) (c) T o replace the lamp: 1. Unplug the power cord. 2. Reverse the projector gently . 3. Loosen the screw (a) using a Phillips screwdriver (+), and remove the lamp cover (b). 4. Loosen the screws (c) using a Phillips screwdriver (+).
EN-33 POWER Off Steady red Blinking red / green ST A TUS Off Off Blinking orange Blinking green Steady red Off Steady or Blinking Solution • Connect the power cord to the projector . • Plug the power cord into a wall outlet. • If any objects are blocking the air inlet or outlet grill, remove them and carry out the following.
EN-34 Images are not displayed corr ectly . Problem Projected images ar e shaking. Projected images ar e displaced. Projected images ar e distorted. Projected images ar e dark. Projected images ar e blurred. White dots are seen on projected images. Black dots are seen on projected images.
EN-35 Others Problem The exhaust vents emit warm air . The menu can’t be used. “TEMPERA TURE!!” is displayed. The mark appears. The remote contr ol doesn’t function easily or at all. The buttons on the control panel (except for the POWER button) don’t function.
EN-36 Indicators POWER Steady green or Steady red Steady red Steady green Steady red Steady red Blinking green/red Blinking green/red ST A TUS Blinking orange Blinking green Blinking green/red Blinking red Steady red Off Steady or Blinking CONDITION Abnormal temperature • The ventilation grilles are clogged with dust or dirt.
EN-37 Specifi cations The specifi cations and outside appearance of the pr ojector are subject to change without prior notice. Ty p e Model Display technology Projection lens Light-source lamp Image.
EN-38 TV60, 480i (525i) - 15.73 59.94 1280 x 720 - TV50, 576i (625i) - 15.63 50.00 1280 x 720 - 1080i 60 (1125i 60) - 33.75 60.00 1280 x 720 - *2 1080i 50 (1125i 50) - 28.13 50.00 1280 x 720 - *2 480p (525p) - 31.47 59.94 1280 x 720 - *2 576p (625p) - 31.
MITSUBISHI Pr ojector Contact Information M I T SUBIS HI ELECTRIC CORPORA T I O N North America MESCA (Mitsubishi Electric Sales Canada Inc.) http://www .
デバイスMitsubishi Electronics HC1500の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Mitsubishi Electronics HC1500をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはMitsubishi Electronics HC1500の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Mitsubishi Electronics HC1500の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Mitsubishi Electronics HC1500で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Mitsubishi Electronics HC1500を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はMitsubishi Electronics HC1500の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Mitsubishi Electronics HC1500に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちMitsubishi Electronics HC1500デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。