Mitsubishi ElectronicsメーカーMELSEC-Fの使用説明書/サービス説明書
ページ先へ移動 of 108
USER’S MANU AL FX 2N -5A S pecia l functi on b loc k.
FX2N-5A Special function b loc k Forew or d • This man ual c ontains t e xt, diag rams a nd e xplanat ions which will guide the re ader in the cor rect ins t all ation and operation of the FX 2N -5A Special function b loc k. It should be read and understood bef ore att empting to install or use the unit.
FX 2N -5A Special function b loc k USER’S MANU AL This manua l confers no in dustria l proper ty right s or any ri ghts of any other kind, nor does it confer any patent licenses .
FX2N-5A Special function b loc k ii.
FX2N-5A Special function b loc k iii Guidelines for the Safety of the User and Pr otection of the FX 2N -5A Special function bloc k. This m anu al pro vides inf or matio n f or the use of th e FX 2N -5A Specia l functi on bl ock. The manua l has been wr itten to be used b y trained and competent personnel.
FX2N-5A Special function b loc k iv Notes on the Symbols Used in this Manua l At v ar ious times through out this manual cer tain sym bols will be us ed to highligh t points which are intended to ens ure the users personal saf ety and protect the integ r ity of equipment.
FX2N-5A Special function b loc k v • Under no ci rcumstances will Mitsubishi Elec tr ic be liab le responsib le f or any consequenti al damage that m ay ar ise as a result of the install ation or use of this equ ipment.
FX2N-5A Special function b loc k vi Note Conce rning the CE Mark ing This docum ent does not guar antee that a mechanic al system incl uding this product will comply with th e f ollowin g stan dards. Compli ance t o EM C stand ards of the en tire mechan ical system should be check ed by the user / manuf actur er .
FX2N-5A Special function b loc k vii EMC The f ollowing produc ts hav e shown compliance through direct testing (of the identified standards belo w) and design analysis (through the creation of a tech.
FX2N-5A Special function b loc k viii T ype : Prog ramma ble Controll er (Open T ype Equipment) Models : FX 2N -5A manuf act ure d from No v ember 1st, 2003 to April 30th, 2006 are complian t with EN5.
FX2N-5A Special function b loc k Contents. ix Guideline ...................... .................................... .............................................. .............. ...... iii 1. Intr oduction . ....... ........ .... ....... ........ ....
FX2N-5A Special function b loc k Contents. x 7.2.12 BFM 21 Writes I/O c haracteristics (o ffset/gain Scaling fun ction setting) (READ/WRITE) ... .............. ............ .............. ........... ............... ........... .............. ... 7-21 7.
FX2N-5A Special function b loc k Contents. xi 8. Adjus tment of I/O Charact eris tics.... ....... ....... ..... ....... ....... ....... ..... ....... 8-1 8.1 Standard I/O characteristi cs ................................ ............................ .
FX2N-5A Special function b loc k Contents. xii.
Introduction 1 1-1 1. Intr od uction The FX 2N -5A analog special function b lock has f our input channels and one output chann el. The input ch annels receiv e analog signals and co nv er ts them to the compar ab le digital v alues . The out put channel ta kes a di gital v alue and outputs an eq uiva lent analog signa l.
FX2N-5A Special function b loc k Introduction 1 1-2 MEMO.
External Dimensions an d Parts 2 2-1 2. External Dimensions and Parts FX -5A POWER 24V AD/DA 2N 24+ 24- VI- OUT V+ I+ V+ VI- V+ I+ VI- I+ VI- V+ I+ V+ I+ VI- IN4 IN3 IN2 IN1 5A 4(0.16") 87(3.43") 9(0.35") 55(2.17") 90(3.54") 1) 10) 9) 2) 80(3.
FX2N-5A Special function block External Dimensions an d Parts 2 2-2 1) Dire ct mo unti ng ho le (2 - φ 4.5) (0.18) 2) Ext ens ion cable 3) P o wer indicator l a mp (LED) 5V po wer is supplied from the progr ammab le controller to lig ht this indicator lamp .
Installation 3 3-1 3. Installation Install the FX 2N -5A to the r ight side of a main unit, e x tensi on unit, e xtension b loc k or special b loc k of the FX 0N /FX 1N /FX 2N /FX 2NC /FX 3G /FX 3GC /FX 3U /FX 3UC Series PLC . The FX 2N -5A can be instal led with DI N rail (DIN46277 of 35 mm in widt h) or directly in stalled with scre ws M4.
FX2N-5A Special function b loc k Installation 3 3-2 Figure 3.1: Installation with DIN rail •T h e F X 2N -5A can be installed on DIN ra il (DIN46277) of 35 mm in width as it is . F or remov al, pull down on the DIN r ail mounting hook, then rem ov e the FX 2N -5A.
Connection to PLC 4 4-1 4. Co nnectio n to PL C Connect the FX 2N -5A to the right side of a main unit, e xtension uni t or e xtension b lock of FX 0N / FX 1N /FX 2N /FX 2NC /FX 3G /FX 3GC /FX 3U /FX 3UC Series PLC wi th an e xtension cab le.
FX2N-5A Special function b loc k Connection to PLC 4 4-2 MEMO.
Wiring 5 5-1 5. Wiring 5.1 Caution 1) Do not la y signal cab ling near to high v oltage po wer cab ling or house them in the sa me trunking duct. Eff ects of noise or surge induction ma y occur . K eep signal cab les at saf e dis- tance of more than 100 mm (3.
FX2N-5A Special function block Wiring 5 5-2 5.2 Input Wiri ng Figure 5.2: Input Wiri ng *1 Use a two-core , shielded twisted pair f or the analog i nput line , and separ ate it from other po wer lines or a lines easily induced.
FX2N-5A Special function block Wiring 5 5-3 5.3 Output Wiring Please ref er to 5.2 f or the wiring f or "24+", "24- " ter minals . Figure 5.3: Output Wiring *1 Use a twis ted pair s hielded c ab le f or the analog output. This cab le should be wired a wa y from pow er lines or an y other lines which coul d induce noise .
FX2N-5A Special function block Wiring 5 5-4 MEMO.
Specifications 6 6-1 6. Specifica tions *1 The criterion is sho wn in IEC61131-2. *2 If the pre ssure is higher than th e atmospheric pressure , do not use FX 2N -5A.
FX2N-5A Special function b loc k Specifications 6 6-2 T able 6.2: P ower supp ly specifications Item Specifi cation s Interf a ce dr iving pow er supp ly 24 V DC±10%, 90 mA (maximum), e xter nally supp lied CPU driving power supply 5 V DC , 70 mA, supplied via e xtension cable from P LC main unit T able 6.
FX2N-5A Special function b loc k Specifications 6 6-3 T able 6.4 : V oltage/current input specifications Item V olta g e input Curren t input Analog i nput range -10 to +10 V DC (input r esistance: 20.
FX2N-5A Special function b loc k Specifications 6 6-4 Resolution • 312.5 µ V (20 V × 1/6400 0) -10 to +10 V at input • 50 µ V (200 mV × 1/4000) -10 0 to +100 mV at inpu t • 10 µ A (40 mA × 1/4000) -20 to +20 mA at inpu t • 1. 25 µ A (40 mA × 1/3200 0) -20 to + 2 0 mA at input • 10 µ A (40 mA × 1/4000) 4 to 20 mA at input • 1.
FX2N-5A Special function b loc k Specifications 6 6-5 T a ble 6.5: V o ltag e/ curren t ou tpu t spe cif icati ons Item V olta ge output Current outp ut Analog output ran ge -10 to +10 V DC (Exter nal.
FX2N-5A Special function b loc k Specifications 6 6-6 MEMO.
Buffer Memor y (BFM) 7 7-1 7. Buff er Memory (BFM) Caution 1) Do not acces s the “Reser v ed” b uff er memor ies “Reser v ed” (BFM #16, #17, #24 , #31 to #40, #46 to # 50, #56 to #70, #75 to # 80, #85 to #90, # 95 to #98, #100, #110, #120 to #199) usin g FROM/T O instr uctions .
FX2N-5A Special function block Buffer Memor y (BFM) 7 7-2 7.1 Buffer Memories (BFM) lists Table 7.1: BFM Lists BFM No. Descri p tion Ho ld agai nst power fail ure Ini tial valu e #0 Spe cifies input mode of CH1 to CH4. { H0000 at shi pment #1 Spe cifies output mode of C H1.
FX2N-5A Special function block Buffer Memor y (BFM) 7 7-3 #18 Hol d last v alue / reset output to offset v alue when PLC is stopped { K0 #19 Disab les setting ch ange of I/O chara cteristics and con venient func tions .
FX2N-5A Special function block Buffer Memor y (BFM) 7 7-4 #25 F ilter mode select ion regi ster { K0 # 2 6 Upper/lower l imit value al ar m status (v alid while BFM #22 b0 or b1 is ON ) ⎯ K0 #27 A/D.
FX2N-5A Special function block Buffer Memor y (BFM) 7 7-5 • • • Reser v ed ⎯⎯ #51 CH1 gai n data (mV , 10 µ V or µ A) { K500 0 at shipment #52 CH2 gai n data (mV , 10 µ V or µ A) { K500 .
FX2N-5A Special function block Buffer Memor y (BFM) 7 7-6 • • • Reser v ed ⎯⎯ #71 CH1 low er limit v alue ala r m set v alue (v alid while BFM #22 b0 or b1 is ON ) { K-3200 0 #72 CH2 low er .
FX2N-5A Special function block Buffer Memor y (BFM) 7 7-7 #84 CH4 upper li mit va lue alarm set val ue (val id while BFM #2 2 b0 or b1 is ON ) { K32000 #85 Reser v ed ⎯ ⎯ #86 Reser v ed ⎯ ⎯ #8.
FX2N-5A Special function block Buffer Memor y (BFM) 7 7-8 #99 Clear upper and low er limit v alue alar m and su dden change detection alar m ⎯ K0 • • • Reser v ed ⎯⎯ #101 CH1 a v erage dat.
FX2N-5A Special function block Buffer Memor y (BFM) 7 7-9 #111 CH1 a v erage data pea k v alue (maximum v alue) (v alid while BFM #22 b2 is ON) ⎯⎯ #112 CH2 a v erage data pea k v alue (maximum v a.
FX2N-5A Special function block Buffer Memor y (BFM) 7 7-10 #200 CH1 Sc aling func tion Anal og V alue 1 This functi on define s a Scalin g input cur v e (simi lar to a look up tab le) f or each chann el.
FX2N-5A Special function block Buffer Memor y (BFM) 7 7-11 #219 CH2 Sc aling func tion Digital V alue 5 This functi on define s a Scalin g input cur v e (simi lar to a look up tab le) f or each chann el.
FX2N-5A Special function block Buffer Memor y (BFM) 7 7-12 7.2 Details of buffe r memories 7.2.1 BFM 0 input mode specification (READ/WRITE) BFM 0 specifies the inp ut mode of CH1 to CH4. T he BFM consists of a 4-d igit he xadecimal code, where one digit is assigned to each input channel.
FX2N-5A Special function block Buffer Memor y (BFM) 7 7-13 8: V oltmeter displa y mode (-100m V to + 100mV) (Displa y r ange -10000 to +10000) 9: Scaling function V oltage input mo de (-10 to +10 V) (.
FX2N-5A Special function block Buffer Memor y (BFM) 7 7-14 7.2.2 BFM 1 output mode specification (READ/WRITE) BFM 1 specifies the output mode of t he analog output CH1 . The BFM consists of a 4-digit he xadec imal cod e , wher e only the lowest digit is assigned t o the an alog o utput cha nnel.
FX2N-5A Special function block Buffer Memor y (BFM) 7 7-15 The out put ch aracter isti cs such as the offs et and gain set tings a re aut omatica lly ch anged dependin g on the setti ngs of B FM 1. A m ode ch ange in B FM 1 will a lso af f ect the se ttings o f BFM 45 (offse t data), BFM 55 (gain dat a), and BFM 240 to 249 (Scaling function da ta).
FX2N-5A Special function block Buffer Memor y (BFM) 7 7-16 7.2.3 BFM 2 to BFM 5 Numbe r of av eraging times (READ/WRITE) The n umber of a v eragi ng times of BFM 2 to BFM 5 s pecify the nu mber of sample s that is used to calcul ate the a v erag e v alues which are d i spla y ed in BFM 6 to BFM 9.
FX2N-5A Special function block Buffer Memor y (BFM) 7 7-17 7.2.4 BFM 6 to BFM 9 A veraged Input Channel data (READ only) The a v er age A/D con v ersion data of each input channel is displa yed i n B FM 6 to BFM 9. The num ber of samples to calcula te the av erage data is influenced b y the setting in BFM 2 to BFM 5) described abo v e.
FX2N-5A Special function block Buffer Memor y (BFM) 7 7-18 7.2.9 BFM 18 hold/ reset analog output when PLC is stopped (READ/WRITE) If BFM 18 is 0, while the PLC base unit is in Stop mode the v alue of BFM15 (v alue of BFM14 + direct ou tput function) will be output.
FX2N-5A Special function block Buffer Memor y (BFM) 7 7-19 7.2.10 BFM 19 setting change enab le/disable (READ/WRITE) BFM 19 per mi ts or proh ibits th e change of the I/O ch aracter is tics f or th e .
FX2N-5A Special function block Buffer Memor y (BFM) 7 7-20 7.2.11 BFM 20 Initialization function (reset all v alues to default) (READ/WRITE) BFM 20 will re set the FX 2N -5A to the f a ctor y def ault.
FX2N-5A Special function block Buffer Memor y (BFM) 7 7-21 7.2.12 BFM 21 Writes I/O characteristi cs (offset/gain Scaling function setting) (READ/WRITE) The b0 to b4 bit s of BFM 21 are assigned to ea ch channel of the FX 2N -5A.
FX2N-5A Special function block Buffer Memor y (BFM) 7 7-22 7.2.13 BFM 22 Con venient functions settin g (RE AD/WRITE) The functio ns descr ibed belo w are assigned to b0 to b3 of BFM 22.
FX2N-5A Special function block Buffer Memor y (BFM) 7 7-23 b8 to b11: s witch of f range o ver/r ange under ala r m f or corresponding i nput channel The v alue of BFM 22 is stored non-v olatile in the int er nal EEPROM.
FX2N-5A Special function block Buffer Memor y (BFM) 7 7-24 Example: V alue in BFM 23 is s e t to H1234. Output v a lue (BFM 15) = BFM 14(T O) - BFM 10 - BFM 7 + BFM 1 2 + BFM 9 If at least o ne He x d.
FX2N-5A Special function block Buffer Memor y (BFM) 7 7-25 7.2.16 BFM 25 Filter -lev el selection register (READ/WRI TE) The f ollo wing T ab le sho ws the possi b le v alues of BFM 25 f or using th e digital Fil ter of the FX 2N -5A-De vice: Table 7.
FX2N-5A Special function block Buffer Memor y (BFM) 7 7-26 F or mula f or filter cut-off freq uency f L : f L = F 1 /(sampling time × no . of activ e channels) [Hz] with cut-off freque ncy f actor F 1 =0.1, 0.05, 0 .025 or 0.01. There are two filter parameters that can be changed, the filter-l e v el and th e cut-off frequency .
FX2N-5A Special function block Buffer Memor y (BFM) 7 7-27 A/D con v ersion v alue when input fil ter is used. Time Analog value Digital value When input filter is used The change of the A/D conversion v alue becomes s mooth. It is smooth when numerical value at leve l is large.
FX2N-5A Special function block Buffer Memor y (BFM) 7 7-28 7.2.17 BFM 26 Upper/lo wer limit v alue alarm status (READ onl y) If the upper/lo wer limit v alue detection function (BFM 22 b0, b1) is used, the detection results are written to BFM 26.
FX2N-5A Special function block Buffer Memor y (BFM) 7 7-29 Table 7.4: Bit assignment in BFM 2 6 Bit No. Channel No. Description b0 CH1 av erage data lower limit v alue alar m b1 av erage data upper li.
FX2N-5A Special function block Buffer Memor y (BFM) 7 7-30 7.2.18 BFM 27 A/D data sud den cha ng e detection status (READ onl y) When the su dden change detect ion function is used, the detection resul t is wr itten to BFM 27. The sudden change detection is activ ated, if the v alues in BFM 91 to BFM 94 are bigger than 0.
FX2N-5A Special function block Buffer Memor y (BFM) 7 7-31 Table 7.5: Bit assignment in BFM27 Bit No. Channel No. Description b0 CH1 a verage data sudden change error in - direction b1 a verage data s.
FX2N-5A Special function block Buffer Memor y (BFM) 7 7-32 7.2.19 BFM 28 Scale o ver status (READ/WRITE) When the a nalog input v alue o f each ch annel (BFM 10 to BF M 13) is outsi de the maximum r ange of the A/D con ver ter , a r ange error alar m is written to BFM 28.
FX2N-5A Special function block Buffer Memor y (BFM) 7 7-33 Table 7.6: Bit assignment in BFM28 Bit No. Channel No. Description b0 CH1 Scale o v er : Less than lo wer limit and disconn ecti on detection.
FX2N-5A Special function block Buffer Memor y (BFM) 7 7-34 7.2.20 BFM 29 Err or status The error inf or mation is ass igned to eac h bit of BFM 29. Table 7.7: Bit assignment in BFM 2 9 Bit No. Assignm ent Description b0 Error dete cted b0 is ON if at leas t one output of b1 to b5 is ON.
FX2N-5A Special function block Buffer Memor y (BFM) 7 7-35 b10 Numbe r of a v erag ing times set ting err or Number of a ver aging times is incorrectly set.Set it within range from 1 to 256. If the no . of av erage data was set to a va lue o utside th e range of 1 to 256, the co rresponding BFM was set to 1.
FX2N-5A Special function block Buffer Memor y (BFM) 7 7-36 The error b1 ap pears when: - in v oltage-mod e: offset data > 5000 gain data < -5000 gain data - offset data < 1000 - in current-mo.
FX2N-5A Special function block Buffer Memor y (BFM) 7 7-37 7.2.21 BFM 30 Model ID code (READ only ) BFM 30 stores the fix ed v alue K1010. Write attempts b y T O instruction are ignored.
FX2N-5A Special function block Buffer Memor y (BFM) 7 7-38 7.2.25 BFM 51 to BFM 54 Analog Input Ga in data (READ/WRITE) Input Gain data : Analog input v alue when the digital v alue is 16000 (or 1 000 in mode 4). The offset d ata and the gain data f or each cha nnel can be s et independently .
FX2N-5A Special function block Buffer Memor y (BFM) 7 7-39 Setting range Ho we ver , the actual eff ectiv e input r ange is "-10 to +10 V", "-20 to +20 mA", "4 to +20 m A" or "-100 to +1 00mV".
FX2N-5A Special function block Buffer Memor y (BFM) 7 7-40 7.2.26 BFM 55 Analog output Gain data (READ/WRITE) Output Gain data : Analog output v oltage or current if digital input in BFM 14 is 1 6000 .
FX2N-5A Special function block Buffer Memor y (BFM) 7 7-41 7.2.27 BFM 71 to BFM 74 Lo wer limit, alarm set v alue (READ/WRITE) 7.2.28 BFM 81 to BFM 84 Upper limit, alarm se t valu e (READ/WRITE) The u.
FX2N-5A Special function block Buffer Memor y (BFM) 7 7-42 A: Scaling fun ction current input mode -32768 to +32767 B: Scaling fun ction voltage input mode -32768 to +327 67 C to E: It is not possible t o set.
FX2N-5A Special function block Buffer Memor y (BFM) 7 7-43 7.2.29 BFM 91 to BFM 94 Su dden c hange detection set v alue (READ/WRITE) When using the sud den change detection func tions , the set va lue to judge the sudden change is written to BFM 91 to 94.
FX2N-5A Special function block Buffer Memor y (BFM) 7 7-44 7.2.30 BFM 99: Clear s upper/lower limit v alue err or and sudd en change detection err or (REA D/ WRITE) The commands to clear the lo wer limit v alue error , upper lim it v alue error and sudden c hange detection error are assigned to the l owe r three bits of BFM 99.
FX2N-5A Special function block Buffer Memor y (BFM) 7 7-45 7.2.31 BFM 101 to BFM 108 P eak v alue (minim um v alue) (READ onl y) 7.2.32 BFM 111 to BFM 118 P eak v alue (maxim um v alue) (READ onl y) W.
FX2N-5A Special function block Buffer Memor y (BFM) 7 7-46 7.2.33 BFM 109: P eak v alue reset flag (minim um v alue) (READ/WRITE) 7.2.34 BFM 119: P eak v alue reset flag (maximum v alue) (READ/WRITE) .
FX2N-5A Special function block Buffer Memor y (BFM) 7 7-47 7.2.35 BFM 200 to BFM 249 Scali ng function (READ/WRITE) The Scalin g function enab les an analog input or output cur v e, f or processes th at are not linear ov er the whole da ta range .
FX2N-5A Special function block Buffer Memor y (BFM) 7 7-48 Scaling function se tting procedures The Scaling function is set acc ording to the f ollow ing procedure . 1) Please mak e a set change in the I/O char acter istic per mission (BFM 19=K 1). ↓ 2) Please wr ite the mode whi ch uses the Scaling function in BFM0 and BFM1.
FX2N-5A Special function block Buffer Memor y (BFM) 7 7-49 Program example when Scal ing function is used Set change permi s sion of I/O characteristic Input mode setti n g Analog input CH1 is set i n.
FX2N-5A Special function block Buffer Memor y (BFM) 7 7-50 Reading of average value data of analog input CH1 (Average value of CH1 → D106) Reading of imm e diate data of analog input CH1 (I mmediate.
FX2N-5A Special function block Buffer Memor y (BFM) 7 7-51 • The r ange in whi ch the analog sca l e v alue and digital v alue can be set v ar ies acco rding to the I/O mode selected f or BFM0 and BFM1. When setting t he analog scale v alue , wr ite the v alue con v er ted to percentage (1/1 00).
FX2N-5A Special function block Buffer Memor y (BFM) 7 7-52 Setting range of analog input Set BFM 0 to 9 Set BFM 0 to A Analog sca le v alue : -10000 to +10000 Analog scale v alue: 2000 to 10000 Digita.
FX2N-5A Special function block Buffer Memor y (BFM) 7 7-53 Set BFM 0 to B Analog sca le v alue : -10000 to +10000 Digital v alue : -32768 to +32 767 Digital value 32767 -10000 (-100mV) -32768 10000 (1.
FX2N-5A Special function block Buffer Memor y (BFM) 7 7-54 Setting range of analog output Set BFM 1 to 9 Set BFM 1 to A Analog sca le v alue : -10000 to +10000 Analog sc ale v alue : 0 to 10000 Digita.
FX2N-5A Special function block Buffer Memor y (BFM) 7 7-55 • The v alue which can be set d epends on the selecti on of BFM 0 and 1. Analog v alues and digit al v alues outside the range selected b y BFM 0 and 1 are set, thus, offset/gain s et v alue error (BFM 29 b1) will occur .
FX2N-5A Special function block Buffer Memor y (BFM) 7 7-56 • When using K0 a s a change point settin g v alue , the subsequent change point v alue must the larger in bo th the "Digital v alue" and "Analog scale val ue". (See figure 2.
FX2N-5A Special function block Buffer Memor y (BFM) 7 7-57 The figure be low sho ws the e xample f or an analog i nput. BFM#206:10000 BFM#207:425 BFM#200:-10000 BFM 201 :50 BFM#202:-4000 BFM#203:275 B.
FX2N-5A Special function block Buffer Memor y (BFM) 7 7-58 If the Scaling f unction is selec ted, the analog m odule will return the f ollo wing v alues in BFM 10: analog inp ut val ue: x < -10000: y = const. 50 (r ange error is entered in BFM28) analog inp ut val ue: -10000 < x < -4000 y = 0.
Adjustment of I/O Characterist ics 8 8-1 8. Adjustment of I/O Characteristics The f actor y , the FX 2N -5A has sta ndard I/O chara cter istics in accordan ce with each input mode (BFM #0, BFM #1 ) set as the f actor y def ault. In the v oltage input mo de and current input mode , adjust th e standar d I/O char acteristics f or each channel.
FX2N-5A Special function b loc k Adjustment of I/O Characterist ics 8 8-2 Input c haracteristics 0. V oltage input, -1 0 to 10V → -32000 to +32000 1. Curre nt input, 4 to 20 mA → 0 to 32000 Digit al val ue -10 10 32000 Approx .327 67 Approx . 10.24 0V Approx .
FX2N-5A Special function b loc k Adjustment of I/O Characterist ics 8 8-3 2.Curr ent inpu t, -20 to 20mA → -32000 t o +320 00 3.V oltage input, -100 to 100mV → - 3 2 00 0 t o + 3 2 0 0 0 4.V oltag e input, -100 t o 100mV → -2000 to +200 0 5. V ol tmete r mode, di rect displa y , -10 to 10 V Digit al val ue -20 20 32000 Approx .
FX2N-5A Special function b loc k Adjustment of I/O Characterist ics 8 8-4 6. Direct current in put, 2 to 20mA 7. Direct current inp ut, -20 to 20mA 8. Direct v oltage input, -100 to 100mV Digit al val ue Input curre nt (mA) 04 2 0 20000 4000 2000 2 Approx .
FX2N-5A Special function b loc k Adjustment of I/O Characterist ics 8 8-5 Output charac teristics 0.V oltage output, -32 000 to +32000 → -10 to 1 0V 1.V oltage outpu t, -2000 to +2000 → -10 to 10V Digit al valu e -10 10 32000 Approx .10. 240 Approx .
FX2N-5A Special function b loc k Adjustment of I/O Characterist ics 8 8-6 2. Current output , 0 to 32000 → 4 to 20 mA 3. Current output, 0 to 1000 → 4 to 20mA 4. Current output , 0 to 32000 → 0 to 20 mA 5. Current output, 0 to 1000 → 0 to 20mA Digit al val ue Output cu rrent (m A) 0 4 20 32000 Approx .
FX2N-5A Special function b loc k Adjustment of I/O Characterist ics 8 8-7 6. Analog v alue direct outp ut, -10 to 10V 7. Analog v alue direct output , 4 to 20mA 8. Analog v alue direct outp ut, 0 to 20mA Digit al valu e -10 10 10000 Approx .10. 239 Approx .
FX2N-5A Special function b loc k Adjustment of I/O Characterist ics 8 8-8 8.2 A djustment o f I/O c haracteri stics Adjust the I/ O characte r istics using the b uff er memories in the FX 2N -5A.
FX2N-5A Special function b loc k Adjustment of I/O Characterist ics 8 8-9 Figure 8.1: Example pr ogram The I/O character istics can be wr itten (BFM #21) to one channel at a time , or two or more channels at a time .
FX2N-5A Special function b loc k Adjustment of I/O Characterist ics 8 8-10 MEMO.
Example program 9 9-1 9. Ex ample pr ogram 9.1 Pr ogram example f or analog input/output The secti on introduces an e xample prog ram to ma nipulate analog input/o utput using the FX 2N -5A.
FX2N-5A Special function b loc k Example program 9 9-2 Figure 9.1: Example pr ogram M8002 K0 K0 H1100 K1 K0 K1 H0000 K1 K0 K10 D110 K4 K0 D114 Spec ifi es t he input mode of CH1 to CH4. Spec if icat ion of a nalog o utput c hannel' s outpu t mo de.
FX2N-5A Special function b loc k Example program 9 9-3 Reading of error st atus (BFM#29 → M120 to M135) K0 K28 H0000 K1 K0 K29 K4M120 K1 M200 M8000 RUN monitor Clears t he s cal e over error FNC 79 TO END FNC 78 FROM K4M120 K4Y 010 FNC 12 MOV Output of error stat us b0 → Y010 b1 → Y011.
FX2N-5A Special function b loc k Example program 9 9-4 9.2 Outline of FROM/T O c ommands FX 2N -5A reads and writes FR OM/T O commands of PLC . FR OM/T O commands are outlined a s f ollows . • When X010 and X011 are OFF , the tr ansf er is not e x ecuted and the data of the transf er destination does not v ar y .
Appendix A A-1 Append ix A: Assoc iated Man uals L ist F or fur ther inf or mation manua l about FX Ser ies , ref er to f ollo wing tab le: T able A-1: Fur ther Inf ormation Manual Manual Name Manual No.
FX2N-5A Special function b loc k Appendix A A-2 FX 3U Series User’ s Manual - Hardware Edition JY997D16501 Th is manual e xplains th e wir ing, installation an d specification for FX 3U Series pr og rammab le contr oller s.
.
HEAD OFFICE: TOKYO BUILDING, 2-7- 3 MARUNOUCHI, CHIYODA- KU, TOKYO 100-8310 , JAPAN HIMEJI WORKS: 840, CHIYODA CHO, HIMEJI, JAPAN JY997D1 1401F (MEE) Effective J uly 2012 Specificatio ns are subject to chan ge without notice.
デバイスMitsubishi Electronics MELSEC-Fの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Mitsubishi Electronics MELSEC-Fをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはMitsubishi Electronics MELSEC-Fの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Mitsubishi Electronics MELSEC-Fの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Mitsubishi Electronics MELSEC-Fで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Mitsubishi Electronics MELSEC-Fを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はMitsubishi Electronics MELSEC-Fの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Mitsubishi Electronics MELSEC-Fに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちMitsubishi Electronics MELSEC-Fデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
