Ariensメーカー932105 - 8526 , 932506 - 8526の使用説明書/サービス説明書
ページ先へ移動 of 30
Owner/Operator Man ual Models 932105 - 8526 932506 - 8526 Sno-Thro ® 00295900 5 / 04 Print ed in USA ENGLIS H FRANÇAI S ESP AÑO L T ransfer model & serial number label from product registration here. Coller l’autocollant du modèle et du numéro de série dans cet encadré.
2 Ariens Company 655 West Ryan S treet P .O. B ox 157 Brillion, Wiscons in 541 10-0157 USA T elephone (920) 756-2141 Facsimile (920) 756-2407 EC DECLARA TION OF CONFORMITY ISSUED BY T HE MANUF ACTURER.
3 CE Sound and Vibrat ion – Niveau sono re et vibration CE – CE-Geräusc hpegel und V ibrations werte – Li vello sonoro e vi b r azioni CE – Sonido y vibrac ión CE – CE-lydnivå o g Vibrasj onsmåling – CE ljud nivå och V ibrations-m ätning – CE- melut aso Tärinä – CE D ź wi ę ku i Wibrac ji Fred J.
GB - 4 Safe ty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Controls a nd Fe a t ure s . . . . . . . . . . . . . . . 12 Oper a t ion . . . . . . . . . . . . . . . . . . .
GB - 5 DISCLAI MER Ariens reserves the r ight to discontinue, make changes to, and ad d improvements upon its products at any time without public notice or obligation. The descriptions and specifications contained in t his manual were in effect at printing.
GB - 6 REQUIRED OPERATOR T RAINING Original purchaser of this unit was instructed by the seller on safe and proper operation. If unit is to be used by som eone other than original purchaser; loaned, r ented or sold, AL WA YS provide this manual and any needed safety training before operation.
GB - 7 AL WA YS remove key and/or wire from spark plug before assembly , maintenance or service. Unintentional engine start up can cause death or serious injury .
GB - 8 DO NOT overload t he mach ine capacity by attempting to clear s now at too fast a rate. DO NOT op erate at too fast a rate. Slow down and t urn corners slowly . Do not operate in r everse unless abs olutely necessary . AL WA YS back up slow ly .
GB - 9 Keep all hardware pr operly tightened. Check shear bolts frequently . Maintain or replace safety and instruction labels, as necessary . NEVER store u nit with fuel in fuel tank, inside a building where an y ignition sources are present such as hot water heaters, space heaters, or clothes dryers .
GB - 10 Inst all Dis charge Chu te Figure 5. 1. Grease discharge chute ring on blower housing (if not already greased). 2. Remove mounting hardware from auger housing. 3. Install discharge chute over opening in the auger housing and secure pedestal to auger housing with hardware removed in step 2.
GB - 1 1 Deflector Remote 1. Remov e e-ring and flat washer from s tud on discharge chute. 2. Route deflector r emote cable between the chute and the chut e pedestal. 3. Slide cable end through hole on bracket on left side of chute (Figure 7). 4. Attach cable eye to stud on deflect or .
GB - 12 Run-in Att achment Belt 1. S t art unit in a well-ventilated area according to Starting and Shut-Off in Operation . 2. Engage attachment clutch lever and run attachment for about 15 minutes. 3. S top unit, wait for all moving parts to st op, and remove spark plug wire.
GB - 13 CONTROLS AND FEA TURES See Figure 8 for all Controls and Feat ures locations. Dual Handle Interlock When Attachment Clutch and th en T raction Drive Clutch are engaged, the Attachment Clutch will remain engaged (leve r down) if released. T o stop attachment, release T raction Drive Clutch and both cl utches will disengage.
GB - 14 Throttle The throttle controls the engine speed. T o increase or decr ease the engine speed, adjust to: 1. Fast (normal or warm starts ) 2. Part-Throttle 3. Slow ( cold weather starts) 4. S top (engine is off) Electric S ta rter (932105) The electric starter will start a properly choked and cranked engine when t he starter button is pushed.
GB - 15 Scraper Blade The scraper blade allows the back of the housing to keep better contact with the surface being cleared. It also prevents damage t o the housing from normal wear . IMPORT ANT : DO NOT allow Scraper Blade to wear too far or Auger/Impeller housing will become damaged.
GB - 16 3. Check Du al Handle Inte rlock Without the engine running, pres s down (engage) both clutch levers. Release attachment clutch lever . Attachment clutch should remain engaged until traction cl utch lever is released, then both clutches must disengage.
GB - 17 IMPORT ANT : DO NO T operate starter more than 15 seconds per minute, as overheating and damage can occur . (If engine does not start, re fer t o T roubleshooting .) 10. Adjust choke as needed. 1 1. Disconnect power cord from outlet, then starter .
GB - 18 * After first two hours of operation. CHECK DUAL HANDLE IN TERL OCK Without the engine running, pres s down (engage) both clutch levers. Release attachment clutch lever . Attachment clutch should remain engaged until traction cl utch lever is released, then both clutches must disengage.
GB - 19 GENERAL LUBRICATION IMPORT ANT : Wipe each fitting clean before and after lubrication. IMPORT ANT : DO NOT allow grea se or oil to get on friction disc, f riction plate or belts. NOTE: Apply Stens Mix Hi-T em p Grease or equivalent to the lubrication fi ttings.
GB - 20 RUNNERS Runners should be adjusted (Figure 14) as conditions require. 1. Position unit on a har d, flat, smooth level surface. 2. Adjust runners by inserting a spacer of desired thickness under center of scraper blade, loosen runner hardware, slide runners to flat surface.
GB - 21 SCRAPER BLADE IMPORT ANT : Dam age to auger/impeller housing will result if blade wears down too far . Scraper blade is adjustable to compensate for wear . T o adjust scraper blade: 1. T ip unit back onto handlebar , support housing and loosen nuts ret a ining blade.
GB - 22 5. Thread the adjustment pivot pin along th e shift rod until it aligns with the mating hole on the speed selector lever . 6. Reinsert the pivot pin int o the hole on t he speed selector lever . 7. Check forward and reverse speeds. a. St art unit.
GB - 23 6. Adjust clutch per Attac hme nt Clutch/Impeller Brake Adjustment below . 7. Replace chute crank and secure with spring pin. 8. Replace belt cover and secure with screws.
GB - 24 d. If spring do es not stretch at least 3/16 in. (4.7 mm), or the belt tension is insufficient to throw snow properly , remove the attachment belt idler (see Figure 18) and replace it in the hole on the idler arm closer to the belt. Adjust cable slack until spring stretch is 3/16 –3/8 in.
GB - 25 2. T urn t he adjustment barrel up t he cable to decrease the d istance between clutch lever and handlebar . T urn the adjustment barrel down the cable to increase the distance between clutch lever and handlebar . 3. Check traction clutch lever distance and repeat adjustment steps if necessary .
GB - 26 5. Bolt new friction disc to shift carrier . T ighten hardware to 5- 6 lbf-ft (6.8 to 8.13 N•m). 6. Install roll pins in hex shaft. Ensure roll pins are centered in hex shaft. 7. Install shift rod on speed selector arm. 8. Install bottom cover .
GB - 27 T ROUBLESHOOTING PROBLEM PROBABLE CAUSE CO RRECTION Engine wi ll not crank/ start. 1. Fuel tank i s empty . 2. Fuel shut-off valve closed. 3. Build up of dirt and residue around governor/carburetor . 4. Key Switch not in run position. 5. Ignition switch starter circuit not functioning.
GB - 28 SPECIFICATIO NS Model Number 932506 932105 Description 8526 8526 Engine - T ecumseh LH318SA LH318SA Pow er Max - HP (Kw/ min -1 ) 8.5 (6.3) Fast Idle S peed-RPM (min -1 ) 3600 ± 150 Displacement - in. (cc) 19.43 (318.3) Electric St art Optional 240V 120V Fuel See Engine Manual T a n k Capa c i ty - q t.
GB - 29 3-Y ear Limited Sno-Thr o W arranty Ariens Company warr ants to the original purchaser that consumer products manufactured by Ariens Company will be free from def ects in material and workmans.
Ariens Company 655 West Ryan Street P .O. Box 157 Brillion, WI 541 10-0157 920-756-2141 Fax 920-756-2407 www .ariens.com.
デバイスAriens 932105 - 8526 , 932506 - 8526の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Ariens 932105 - 8526 , 932506 - 8526をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはAriens 932105 - 8526 , 932506 - 8526の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Ariens 932105 - 8526 , 932506 - 8526の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Ariens 932105 - 8526 , 932506 - 8526で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Ariens 932105 - 8526 , 932506 - 8526を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はAriens 932105 - 8526 , 932506 - 8526の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Ariens 932105 - 8526 , 932506 - 8526に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちAriens 932105 - 8526 , 932506 - 8526デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
