Mitsubishi ElectronicsメーカーWD8700Uの使用説明書/サービス説明書
ページ先へ移動 of 19
1 DLP™ Pr ojector WD8700U Contr olling the pr ojector via RS-232C connection Contents 1. Introduction ............................................................................................................ 2 1.1 Connection .....................
2 1 . Introduct ion This projector can be contr olled by connecting a personal computer with RS-232C terminal. In addition, by connecting multiple projectors to each other in a daisy chain configuration, you can contr ol each projector fr om one personal computer .
3 • Example of ID setting (When Group A, which performs multi-pr ojection with two projectors, and Group B, which performs multi-projection with thr ee projectors, are connected.
4 2 . Cont rol com man d config ur ati on The command consists of the address code, ID code, function code, data code, ACK/NAK, and end code. The length of the command varies among the functions.
5 • The projector may not r eceive a command when the splash screen is being displayed immediately after turning on the power . Use command “00r10” to cancel the splash screen. • While using the LAN terminals, the LAN functions take precedence.
6 Projector error Send out “00vER” to check error details. Recover from error state. 0– 3 To normal operation 4 Enter password. Send out “00PASS****.
7 4. Execut io n proc edu re of RS -232 C comma nd s via L A N • When you use the LAN function, set the ST ANDBY MODE to ST ANDARD or LAN. • When you execute RS-232C commands via LAN, check that the CONTROL SYSTEM in the NETWORK menu is set to ST ANDARD.
8 5. Comma nd lis t 5. 1 Gen er al co nt rol c omm an ds The general control commands are used for the basic operation setting of this projector . They may not be exe- cuted while the signals are changed. The general control commands have no data codes.
9 5. 2 . 2 Read co mma nd s for i tem s in IN FORMA TION me nu Use the following commands to obtain the values of the items in the INFORMA TION menu. ITEM Function Data (Receive) Character ASCII code .
10 [Example] When checking the currently selected input terminal (when the INPUT VIDEO is being selected). (V alues enclosed in quotation marks are ASCII codes.
11 [Example] When displaying the MENU selection bar . (V alues enclosed in quotation marks are ASCII codes.): • When ID is not specied: Command sent from the PC, etc.
12 5. 5 Funct ion c omma nd s (Not executable in stand-by m ode. When the mute comman ds are sent while the spl ash screen is being displayed, the splash screen is only canceled.
13 ITEM Function Data Character ASCII code NOISE REDUCTION NR 4Eh 52h 0 (OFF), 1 (ON) CTI CTI 43h 54h 49h 0 (OFF), 1 (ON) INPUT LEVEL IPL 49h 50h 4Ch ±5, For DVI input: +0 (NORMAL), +1 (ENHANCED) For.
14 ITEM Function Data Character ASCII code REMOTE 1 MODE (RESET) R1MRST 52h 31h 4Dh 52h 53h 54h FIL TER MENU (CLEANUP PERIOD) FLCP 46h 4Ch 43h 50h xdhh x: Cleanup interval 0 (OFF), 1 (24H), 2 (1WEEK) dhh: Next cleanup time (d: days, hh: hours) OFF: Fixed to 0 days and 00 hours 24H: Max.
15 ITEM Function Data Character ASCII code COLOR MA TCHING- MANUAL (RESET) MNRST 4Dh 4Eh 52h 53h 54h COLOR MA TCHING- -MEASURE-MEASURED DA T A (Y(Relative value)) MSML 4Dh 53h 4Dh 4Ch x00050 to 20000 x: Color selection R (RED), G (GREEN), B (BLUE), W (WHITE) COLOR MA TCHING- -MEASURE-MEASURED DA T A (x) MSMX 4Dh 53h 4Dh 58h x*.
16 5.6 .6 SIG NA L men u ITEM Function Data Character ASCII code MEMOR Y CALL MMC 4Dh 4Dh 43h 0 (AUTO), 1 to 8 (MEMOR Y 1 to 8) HORIZ.POSITION HP 48h 50h + (increment), - (decrement) *1 VERT . POSITION VP 56h 50h + (incr ement), - (decrement) *1 FINE SYNC.
17 How to set the value Use the character or ASCII code as shown below to set the value. Character + - 0 1 2 3 4 5 6 7 8 9 ASCII code ‘2Bh’ ‘2Dh’ ‘30h’ ‘31h’ ‘32h’ ‘33h’ ‘34h’ ‘35h’ ‘36h’ ‘37h’ ‘38h’ ‘39h’ [Example 1] When setting the AUTO POWER ON to ON.
18 [Example 3] When checking the TINT setting (when the TINT is set to +10). (V alues enclosed in quotation marks are ASCII codes.): • When ID is not specied: Command sent from the PC, etc. Status code returned from the pr ojector Description ‘30’ ‘30’ ‘53’ ‘0D’ 00S Command for checking the TINT setting (ID command is omitted.
19 5.7 Passwor d loc k com man ds The password lock commands control the password lock. The password lock enabling or disabling command is sent with a 4 to 8-digit password comprised of any figures 1 to 4 added to the end of the data code.
デバイスMitsubishi Electronics WD8700Uの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Mitsubishi Electronics WD8700Uをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはMitsubishi Electronics WD8700Uの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Mitsubishi Electronics WD8700Uの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Mitsubishi Electronics WD8700Uで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Mitsubishi Electronics WD8700Uを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はMitsubishi Electronics WD8700Uの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Mitsubishi Electronics WD8700Uに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちMitsubishi Electronics WD8700Uデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。