Mitsubishi ElectronicsメーカーXD460Uの使用説明書/サービス説明書
ページ先へ移動 of 40
XD490 XD460 DLP™ PROJECTOR MODEL XD490U XD460U User Manual This User Manual is important to you. Please r ead it befor e using your pr ojector . ENGLISH.
EN-2 CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK) NO USER-SERVICEABLE P ARTS INSIDE REFER SERVICING TO QUALIFIED SER VICE PERSONNEL.
EN-3 ENGLISH Contents Declaration of Conformity Model number : XD490U/XD460U T rade name : MITSUBISHI ELECTRIC Responsible party : Mitsubishi Digital Electronics America, Inc. 9351 Jeronimo Road, Irvine, CA 92618 U.S.A T elephone number : +1-(949) 465-6000 This device complies with Part 15 of the FCC Rules.
EN-4 Important safeguar ds Please read all these instructions r egar ding your projector and r etain them for futur e refer ence. Follow all warnings and instructions marked on the projector . 1. Read instructions All the safety and operating instructions should be read befor e the appliance is operated.
EN-5 ENGLISH WARNING: Unplug immediately if there is something wrong with your pr ojector . Do not operate if smoke, strange noise or odor comes out of your projector . It might cause fi re or electric shock. In this case, unplug immediately and contact your dealer .
EN-6 Pr eparing your pr ojector 1 2 3 Checking accessories The following accessories are pr ovided with this pr ojector . Check to be sure that all of the accessories ar e packed in the package. Important: • The attached power cords are to be used exclusively for this pr oduct.
EN-7 ENGLISH Overview 3 2 1 5 7 10 9 8 6 4 2 1 3 4 8 5 6 7 9 KEYSTONE AUTO POSITION VIDEO COMPUTER ENTER MENU VOLUME 1 FOCUS ring 2 ZOOM ring 3 Control panel 4 Air outlet grille 5 Remote contr ol sens.
EN-8 1 2 3 Pr eparating your pr ojector (Continue) Bottom side 1 Adjustment foot (Front) 2 Lamp cover 3 Adjustment feet (Rear) Caution: Do not replace the lamp immediately after using the projector because the lamp would be extr emely hot and it may cause burns.
EN-9 ENGLISH Using the r emote contr ol 30° 30° 30° 30° 20° 10° 20° 10° 20° 20° 20° 20° Operational range of the r emote contr ol • Keep the remote control photo-sensor out of dir ect sunlight or fl uor escent lamp light. • Keep the remote control photo-sensor at least 2 m away from fl uor escent lamps.
EN-10 Setting up your pr ojector W A A=B B Setting up the screen Install the screen perpendicularly to the pr ojector . If the screen can not be installed in such a way , adjust the projection angle of the pr ojector .
EN-11 ENGLISH Front pr ojection, ceiling mounting For ceiling mounting, you need the ceiling mount kit de- signed for this projector . Ask a specialist for installation.
EN-12 Scr een size and pr ojection distance Refer to the following table to determine the screen size. B A Hd When the aspect ratio of the screen is 4:3 40 102 24 61 32 81 51 1.3 62 1.6 2.8 7 60 152 36 91 48 122 77 2.0 94 2.4 4.3 11 80 203 48 122 64 163 103 2.
EN-13 ENGLISH 2 1 2 1 Viewing computer images A. Connecting the projector to a computer Preparation: • Make sure that the power of the projector and that of the computer ar e tur ned off. • When connecting the projector to a desktop computer , disconnect the RGB cable that is connected to the monitor .
EN-14 1 Plug the attached power cor d into the power cord inlet of this projector . 2 Plug the other end of the power cor d into a power outlet. • The power cords for use in the U.S. and Europe ar e included with this projector . Use the appropriate one for your country .
EN-15 ENGLISH C. Projecting images Preparation: • Remove the lens cap. • T ur n on the power of the connected computer . 1. Confi rm the POWER indicator lights up r ed.
EN-16 Viewing computer images (continued) T o stop projecting: 8. Pr ess the POWER button. • A confi rmation message is displayed. • T o cancel the procedur e, leave the projector for a while or press the MENU button. 9. Pr ess the POWER button. • The lamp goes out and the projector goes into a standby mode.
EN-17 ENGLISH 1 2 3 4 1 3 4 2 Connecting to a video player , etc. 1. Connect one end (yellow) of the supplied audio/video cable to the VIDEO terminal of the projector . 2. Connect one end (white and r ed) of the supplied audio/ video cable to the audio input terminals (L/MONO, R) of the projector .
EN-18 Connecting to video equipment having a DVI-D terminal Y ou can project high-quality images by connecting the DVI-D terminal of this projector to video equipment having a DVI-D output terminal. In addition, this projector supports HDCP and is able to r eceive encrypted digital video data that are output fr om DVD players.
EN-19 ENGLISH C. Pr ojecting images Preparation: • Remove the lens cap. • T ur n on the power of the connected video equipment. 1. Confi rm the POWER indicator lights up r ed.
EN-20 T o stop projecting: 8. Press the POWER button. • A confi rmation message is displayed. • T o cancel the procedur e, leave the projector for a while or press the MENU button. 9. Pr ess the POWER button. • The lamp goes out and the projector goes into a standby mode.
EN-21 ENGLISH Setting the aspect ratio Y ou can change the aspect ratio of the input video signal (or the ratio of width to height of the image). Change the setting according to the type of the input video signal. How to change the settings: With the remote contr ol: 1.
EN-22 Menu operation • Menus are not displayed when no signal is supplied to the projector . * 1: Not available when GAMMA MODE is set to sRGB. * 2: Not available with certain signals. * 3: Setting range differs depending on the setting of SCREEN SIZE.
EN-23 ENGLISH IMAGE opt. CONTRAST BRIGHTNESS 0 0 ST ANDARD 0 0 0 COLOR TINT SHARPNESS COLOR TEMP . AUTO COLOR ENHANCER XGA60 INST ALLATION opt. ON SPLASH SCREEN WALL SCREEN VIRTUAL LENS SHIFT AUTO POWER OFF BACK COLOR LAMP MODE OFF OFF OFF BEIGE ON BLUE AUTO POWER ON ST ANDARD OFF IMAGE REVERSE XGA60 FEA TURE AUTO XGA60 AUTO opt.
EN-24 3. FEA TURE menu ITEM SETTING FUNCTION ASPECT AUTO Select to change the aspect ratio automatically depending on the input signal. 16:9 Select to project images with an aspect ratio of 16:9. REAL Select to pr oject images in their original size as input.
EN-25 ENGLISH Adjusting pr ojected images T o adjust the brightness (CONTRAST and BRIGHTNESS): Y ou can make adjustments for the brightness of the projected image using the menu. (See Page 22 for menu setting.) 1. Display the IMAGE menu. 2. Select CONTRAST or BRIGHTNESS by pressing the or button.
EN-26 T o adjust the tone of white (COLOR TEMP .): Y ou can select a preset color temperature (white tone) using the menu. (See Page 22 for menu setting.) 1. Display the IMAGE menu. 2. Select COLOR TEMP . by pressing the or button. 3. Select your desired color temperature by pr essing the or button.
EN-27 ENGLISH This projector automatically and pr operly projects video signals supplied from the computer . However , some video signals may not be projected, depending on the type of the computer . In such a case, press the AUTO POSITION button. (See Page 16.
EN-28 MENU ACCESS XGA60 opt. LOCK UNLOCK OK OK P ASSWORD CONFIRM O K CANCEL MENU ACCESS XGA60 opt. LOCK UNLOCK OK OK P ASSWORD O K CANCEL Password function This projector is equipped with the passwor d function that is designed for prevention of wr ong operation by children and r estriction on operation by other than specifi ed users.
EN-29 ENGLISH Expand By pressing the EXP AND button on the remote control, you can magnify the image to view the details. • The EXP AND mode doesn't function with some input signals. For details, see page 38. Still T o stop the motion in the image temporarily (or to dis- play a still image): Press the STILL button on the r emote control.
EN-30 Mouse remote contr ol By connecting to personal computer through the USB port, you can operate your computer with the pr ojector remote control. Projector + computer with USB connector Operation • Y ou can use the mouse remote control function with a computer supporting USB only .
EN-31 ENGLISH Replacing the lamp This projector is equipped with a lamp to pr oject images. This lamp is a consumable. It may bur n out or its brightness may decrease during use. In such cases, r eplace the lamp with a new one as soon as possible. Be sure to replace the lamp with a new lamp separately sold that is exclusive to this projector .
EN-32 T o replace the lamp: 1. Reverse the pr ojector gently . 2. Loosen the scr ew (a) using a Phillips screwdriver (+), and remove the lamp cover (b). 3. Loosen the scr ews (c) using a Phillips screwdriver (+). 4. Pull up the handle. 5. Pull out the lamp box by the handle while holding the projector .
EN-33 ENGLISH POWER Off Steady red Blinking red / green ST A TUS Off Off Blinking orange Blinking green Steady red Off Steady or Blinking Solution • Connect the power cord to the projector . • Plug the power cord into a wall outlet. • If any objects are blocking the air inlet or outlet grille, remove them and carry out the following.
EN-34 Images are not displayed corr ectly . Problem Projected images ar e shaking. Projected images ar e displaced. Projected images ar e distorted. Projected images ar e dark. Projected images ar e blurred. White dots are seen on projected images. Black dots are seen on projected images.
EN-35 ENGLISH Others Problem The exhaust vents emit warm air . No audio is output. The menu can't be used. “TEMPERA TURE!!” is displayed. The mark appears. The remote contr ol doesn't function easily or at all. The buttons on the control panel (except for the POWER button) don’t function.
EN-36 Indicators POWER Steady green or Steady red Steady red Steady green Steady red Steady red Blinking green/red Blinking green/red ST A TUS Blinking orange Blinking green Blinking green/red Blinking red Steady red Off Steady or Blinking CONDITION Abnormal temperature • The ventilation grilles are clogged with dust or dirt.
EN-37 ENGLISH Specifi cations The specifi cations and outside appearance of the pr ojector are subject to change without prior notice. Replacement part (Option / Not included in the box) Spare lamp .
EN-38 TV60, 480i(525i) - 15.73 59.94 1024 x 768 - *1 TV50, 576i(625i) - 15.63 50.00 1024 x 768 - *1 1080i 60 (1125i 60) - 33.75 60.00 1024 x 576 - *1, *3 1080i 50 (1125i 50) - 28.13 50.00 1024 x 576 - *1 1080i 50a (1250i 50) - 31.25 50.00 1024 x 576 - *1 480p (525p) - 31.
EN-39 ENGLISH 1 R(RED)/C R 2 G(GREEN)/Y 3 B(BLUE)/C B 4 GND 5 GND 6 GND 7 GND 8 GND 9 DDC 5V 10 GND 11 GND 12 DDC Data 13 HD/CS 14 VD 15 DDC Clock 1 TXD IN 2 - - 3 - - 4 GND - 5 - - 6 - - 7 RXD OUT 8 - - 1 35 2 68 1 5 11 6 10 15 SERIAL (8-pin) Pin No.
MITSUBISHI Pr ojector Contact Information Manufactur ed by Mitsubishi Electric Corporation 1 Zusho Baba, Nagaokakyo-City , Kyoto Japan M I T SUBIS HI ELECTRIC CORPORA T I O N North America MESCA (Mitsubishi Electric Sales Canada Inc.) http://www .mitsubishielectric.
デバイスMitsubishi Electronics XD460Uの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Mitsubishi Electronics XD460Uをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはMitsubishi Electronics XD460Uの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Mitsubishi Electronics XD460Uの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Mitsubishi Electronics XD460Uで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Mitsubishi Electronics XD460Uを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はMitsubishi Electronics XD460Uの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Mitsubishi Electronics XD460Uに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちMitsubishi Electronics XD460Uデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
