MitsubishiメーカーXD1000の使用説明書/サービス説明書
ページ先へ移動 of 41
XD2000 XD1000 DLP™ PROJECTOR MODEL XD2000U XD1000U User Manual This User Manual is important to you. Please read it befor e using your projector . ENGLISH.
EN-2 CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK) NO USER-SERVICEABLE P ARTS INSIDE REFER SERVICING TO QUALIFIED SER VICE PERSONNEL.
EN-3 ENGLISH Contents Important safeguards .......................................................................................................... .............. 4 Preparing your pr ojector ..........................................................
EN-4 Important safeguar ds Please read all these instructions r egarding your projector and r etain them for future refer ence. Follow all warnings and instructions marked on the projector . 1. Read instructions All the safety and operating instructions should be read befor e the appliance is operated.
EN-5 ENGLISH WARNING: Unplug immediately if there is something wrong with your pr ojector . Do not operate if smoke, strange noise or odor comes out of your projector . It might cause fi r e or electric shock. In this case, unplug immediately and contact your dealer .
EN-6 Pr eparing your projector 1 2 3 Checking accessories The following accessories are pr ovided with this projector . Check to be sure that all of the accessories are packed in the package. Important: • The attached power cords are to be used exclusively for this pr oduct.
EN-7 ENGLISH Overview Control panel T erminal board 1 2 6 7 8 4 5 3 POWER MENU ENTER S TAT U S AUTO POSITION COMPUTER ZOOM/FOCUS LENS SHIFT KEYSTONE VIDEO VOLUME 1 5 6 2 3 4 7 8 9 11 10 1 Speaker 2 Co.
EN-8 1 2 Preparating your projector (continued) Bottom side 1 Lamp cover 2 Adjustment feet Caution: Do not replace the lamp immediately after using the projector because the lamp would be extremely hot and it may cause burns.
EN-9 ENGLISH Using the r emote control Operational range of the remote contr ol • Keep the remote control photo-sensor out of dir ect sunlight or fl uor escent lamp light. • Keep the remote contr ol photo-sensor at least 2 m away from fl uorescent lamps.
EN-10 W A A=B B Setting up your pr ojector Setting up the screen Install the screen perpendicularly to the pr ojector . If the screen can not be installed in such a way , adjust the projection angle of the pr ojector .
EN-11 ENGLISH Front pr ojection, ceiling mounting For ceiling mounting, you need the ceiling mount kit de- signed for this projector . Ask a specialist for installation.
EN-12 Screen size and pr ojection distance Refer to the following table to determine the screen size. When the aspect ratio of the screen is 4:3 Screen size Projected distance (L) Lens movable range 4:3 Diagonal size Height (H) Width (W) Min.
EN-13 ENGLISH 2 1 AUDIO OUT AUDIO IN 2 1 2 1 Viewing computer images A. Connecting the projector to a computer Preparation: • Make sure that the power of the projector and that of the computer ar e tur ned off. • When connecting the projector to a desktop computer , disconnect the RGB cable that is connected to the monitor .
EN-14 2 1 1. Plug the attached power cord into the power cord inlet of this projector . 2. Plug the other end of the power cord into a power outlet. • The power cords for use in the U.S. and Europe ar e included with this projector . Use the appropriate one for your country .
EN-15 ENGLISH POWER MENU ENTER S TAT U S AUTO POSITION COMPUTER ZOOM/FOCUS LENS SHIFT KEYSTONE VIDEO VOLUME C. Projecting images Preparation: • Remove the lens cap. 1. Put the projector into standby mode by pressing the main power switch. The POWER indicator lights up r ed.
EN-16 POWER MENU ENTER ST A TUS AUTO POSITION COMPUTER ZOOM/FOCUS LENS SHIFT KEYSTONE VIDEO VOLUME Viewing computer images (continued) T o stop projecting: 13. Press the POWER button. • A confi rmation message is displayed. • T o cancel the procedure, leave the pr ojector for a while or press any button except the POWER button.
EN-17 ENGLISH Connecting to a video player , etc. 1. Connect one end (yellow) of the supplied audio/video cable to the VIDEO IN terminal of the projector . 2. Connect one end (white and red) of the supplied audio/ video cable to the audio input terminals (L/MONO, R) of the projector .
EN-18 C B (P B ) Y C R (P R ) B G R AUDIO IN-2 BNC cable (Option) DVD player or HDTV decoder BNC - RCA connector (option) COMPUTER IN/COMPONENT VIDEO IN-2 Connecting to video equipment having a DVI-D terminal Y ou can project high-quality images by connecting the DVI-D terminal of this pr ojector to video equipment having a DVI-D output terminal.
EN-19 ENGLISH C. Projecting images Preparation: • Remove the lens cap. 1. Put the projector into standby mode by pressing the main power switch. The POWER indicator lights up r ed.
EN-20 T o stop projecting: 13. Press the POWER button. • A confi rmation message is displayed. • T o cancel the procedure, leave the pr ojector for a while or press any button except the POWER button. 14. Press the POWER button again. • The lamp goes out and the projector goes into a standby mode.
EN-21 ENGLISH Setting the aspect ratio Y ou can change the aspect ratio of the input video signal (or the ratio of width to height of the image). Change the setting according to the type of the input video signal. How to change the settings: With the remote contr ol: 1.
EN-22 Menu operation • Menus are not displayed when no signal is supplied to the projector . * 1: Not available when COLOR ENHANCER is set to sRGB. * 2: Not available with certain signals. * 3: Available only when the input signal is TV50, TV60, 480i or 576i.
EN-23 ENGLISH IMAGE opt. CONTRAST BRIGHTNESS 0 0 STANDARD 0 0 0 COLOR TINT SHARPNESS COLOR TEMP . AUTO COLOR ENHANCER XGA60 INST ALLATION opt. ON SPLASH SCREEN AUTO POWER OFF BACK COLOR LAMP MODE OFF .
EN-24 3. FEA TURE menu ITEM SETTING FUNCTION ASPECT AUTO Select to change the aspect ratio automatically depending on the input signal. (Select this option for normal use.) 16:9 This option allows you to select the display position of squeezed (or horizontally compressed) images stor ed on DVD discs.
EN-25 ENGLISH Adjusting pr ojected images T o adjust the brightness (CONTRAST and BRIGHTNESS): Y ou can make adjustments for the brightness of the projected image using the menu. (See page 22 for menu setting.) 1. Display the IMAGE menu. 2. Select CONTRAST or BRIGHTNESS by pressing the or button.
EN-26 T o adjust the tone of white (COLOR TEMP .): Y ou can select a preset color temperatur e (white tone) using the menu. (See page 22 for menu setting.) 1. Display the IMAGE menu. 2. Select COLOR TEMP . by pressing the or button. 3. Select your desired color temperature by pr essing the or button.
EN-27 ENGLISH This projector automatically and pr operly projects video signals supplied from the computer . However , some video signals may not be projected, depending on the type of the computer . In such a case, press the AUTO POSITION button. (See page 16.
EN-28 MENU ACCESS FEA TURE XGA60 opt. LOCK UNLOCK OK OK P ASSWORD CONFIRM O K CANCEL MENU ACCESS FEA TURE XGA60 opt. LOCK UNLOCK OK OK P ASSWORD O K CANCEL Password function This projector is equipped.
EN-29 ENGLISH Expand By pressing the EXP AND button on the remote control, you can magnify the image to view the details. Picture in Pictur e (PinP) One of the special features of this pr ojector is the picture-in-pictur e (PinP) mode. The PinP mode allows you to view the images from dif ferent sources at the same time.
EN-30 Mouse remote contr ol By connecting to personal computer through the USB port, you can operate your computer with the pr ojector remote control. Projector + computer with USB connector Operation • Y ou can use the mouse remote contr ol function with a computer supporting USB only .
EN-31 ENGLISH Supervising and controlling by computer Y ou can supervise and control the pr ojector’ s operation using a personal computer via a LAN network. • T o supervise and control the pr ojector , install the software “Mitsubishi Pr ojector Control Device Installer *” con- tained in the attached CD-ROM.
EN-32 Replacing the lamp This projector is equipped with a lamp to pr oject images. This lamp is a consumable. It may bur n out or its brightness may decrease during use. In such cases, r eplace the lamp with a new one as soon as possible. Be sure to replace the lamp with a new lamp separately sold that is exclusive to this projector .
EN-33 ENGLISH T o replace the lamp: 1. Reverse the projector gently . 2. Loosen the screw (a) using a Phillips screwdriver (+), and remove the lamp cover (b). 3. Loosen the screws (c) using a Phillips screwdriver (+). 4. Pull up the handle. 5. Pull out the lamp box by the handle while holding the projector .
EN-34 POWER Off Steady red Blinking red / green ST A TUS Off Off Blinking orange Blinking green Steady red Off Steady or Blinking Solution • Connect the power cord to the projector . • Plug the power cord into a wall outlet. • If any objects are blocking the air inlet or outlet grille, remove them and carry out the following.
EN-35 ENGLISH Images are not displayed corr ectly . Problem Projected images ar e shaking. Projected images ar e displaced. Projected images ar e distorted. Projected images ar e dark. Projected images ar e blurred. White dots are seen on projected images.
EN-36 Others Problem The exhaust vents emit warm air . No audio is output. The menu can't be used. “TEMPERA TURE!!” is displayed. The mark appears. The remote contr ol doesn't function easily or at all. The buttons on the control panel (except for the POWER button) don’t function.
EN-37 ENGLISH Indicators POWER Steady green or Steady red Steady red Steady green Steady red Steady red Blinking green/red Blinking green/red ST A TUS Blinking orange Blinking green Blinking green/red Blinking red Steady red Off Steady or Blinking CONDITION Abnormal temperature • The ventilation grilles ar e clogged with dust or dirt.
EN-38 Specifi cations The specifi cations and outside appearance of the pr ojector are subject to change without prior notice. *1 : Wireless LAN unit isn’ t packaged together with the projector .
EN-39 ENGLISH TV60, 480i(525i) - 15.73 59.94 1024 x 768 - *1, *3 TV50, 576i(625i) - 15.63 50.00 1024 x 768 - *1, *3 1080i 60 (1125i 60) - 33.75 60.00 1024 x 576 - *1, *2 1080i 50 (1125i 50) - 28.13 50.00 1024 x 576 - *1 1080i 50a (1250i 50) - 31.25 50.
EN-40 1 R(RED)/C R 2 G(GREEN)/Y 3 B(BLUE)/C B 4 GND 5 GND 6 GND 7 GND 8 GND 9 DDC 5V 10 GND 11 GND 12 DDC Data 13 HD/CS 14 VD 15 DDC Clock 1 - - 2 TXD IN 3 RXD OUT 4 - - 5 GND - 6 - - 7 - - 8 - - 9 - - 1 5 11 6 10 15 SERIAL (D-SUB 9-pin) Pin No. Name I/O COMPUTER IN / COMPONENT VIDEO IN (Mini D-SUB 15-pin) Pin No.
MITSUBISHI Projector Contact Information Manufactured by Mitsubishi Electric Corporation 1 Zusho Baba, Nagaokakyo-City , Kyoto Japan M I T SUBIS HI ELECTRIC CORPORA T I O N North America MESCA (Mitsubishi Electric Sales Canada Inc.) http://www .mitsubishielectric.
デバイスMitsubishi XD1000の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Mitsubishi XD1000をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはMitsubishi XD1000の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Mitsubishi XD1000の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Mitsubishi XD1000で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Mitsubishi XD1000を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はMitsubishi XD1000の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Mitsubishi XD1000に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちMitsubishi XD1000デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。