Moxa TechnologiesメーカーEDS-508の使用説明書/サービス説明書
ページ先へ移動 of 46
MOXA EtherDevice TM Switch EDS - 508 Hardware Installation Guide First Edition, April 200 4.
MOXA EtherDevice TM Switch EDS - 508 Hardware Installation Guide The software described in this manual is furnished under a license agreement and may be used only in accordance with the terms of that agreement. Copyright Notice Copyright ? 200 4 Moxa Networking Co.
Table of Contents 1 Chapter 1: I ntroduction ............................................................ 1 - 1 Why EDS - 508 is ideal for Industr ial Control and Automation ............... 1 - 2 Package Checklist .....................................
4 Chapter 4: H ardware Overview ............................................... 4 - 1 Redundant Power Inputs ................................................................................ 4 - 2 Relay Contacts ........................................
1 1 1 Introduction Welcome to MOXA EtherDevice ™ S witch EDS - 508 , an i ndustrial 8 - Port Managed Redundant Ethernet Switches . The following topics are covered in this chapter: ? ? Why EDS - 508.
MOXA EtherDevice S witch Hardware Installation Guide 1 - 2 Why EDS - 508 is ideal for Industrial Control and Automation ? ? Advanced Network Control Function Multicast traffic management — IGMP Snooping function provides the ability to manage multicast traffic.
Introduction MOXA EtherDevice S witch Hardware Installation Guide 1 - 3 ? ? Industrial Grade Reliability Extended operating temperature capability — To ensure that your Ethernet equipment can withstand harsh environmental conditions ( - 40 to 75°C).
MOXA EtherDevice S witch Hardware Installation Guide 1 - 4 ? ? EDS - SNMP OPC Server: CD with EDS - SNMP OPC Server Software and manual ? ? ADP - SCm - STf - M : Multi - mode SC male to ST female dupl.
Introduction MOXA EtherDevice S witch Hardware Installation Guide 1 - 5 o - 40 to 75°C operating temperature range o IP 30, rugged high - strength case o DIN - Rail or panel mo unting ability ?? Usef.
MOXA EtherDevice S witch Hardware Installation Guide 1 - 6 Panel Views of ED S - 508 1. 1. Grounding screw 2. Console port 3. Heat dissipation orifices 4. 6 - pin t erminal block for DI 1, DI 2 and PWR 2 5. 6 - pin t erminal block for PWR1, Relay 1 and Relay 2 6.
Introduction MOXA EtherDevice S witch Hardware Installation Guide 1 - 7 Panel V iews of ED S - 508 - MM - SC 1. Grounding screw 2. Console port 3. Heat dissipation orifices 4. 6 - pin t erminal block for DI 1, DI 2 and PWR 2 5. 6 - pin t erminal block for PWR1, Relay 1 and Rela y 2 6.
MOXA EtherDevice S witch Hardware Installation Guide 1 - 8 Panel Views of ED S - 508 - SS - SC 1. Grounding screw 2. Console port 3. Heat dissipation orifices 4. 6 - pin t erminal block for DI 1, DI 2 and PWR 2 5. 6 - pin t erminal bl ock for PWR1, Relay 1 and Relay 2 6.
2 2 2 Installing MOXA EtherDevice TM Switch This chapter includes information about installing MOXA EtherDevice TM Switch . The following topics are covered: ? ? Mounting Dimensions ? ? DIN - Rail Mou.
MOXA EtherDevice S witch Hardware Installation Guide 2 - 2 Mounting Dimensions.
Install in g MOXA EtherDevice S witch MOXA EtherDevice S witch Hardware Installation Guide 2 - 3 DIN - Rail Mounting The aluminum DIN - Rail attachment plate should already be fixed to the back panel of EDS - 508 when yo u take it out of the box.
MOXA EtherDevice S witch Hardware Installation Guide 2 - 4 Wall Mounting (O ptional ) For some applications, you will find it convenient to mount MOXA EDS - 508 on the wall, as illustrated below.
Install in g MOXA EtherDevice S witch MOXA EtherDevice S witch Hardware Installation Guide 2 - 5 STEP 2 : Mounting MOXA EDS - 508 on the wall requires 4 screws. Use the EDS - 508 , with wall mount plates attached, as a guide to mark the correct locations of the 4 screws.
.
3 3 3 Wiring MOXA EtherDevice TM S witch This chapter includes technical information about connecting MOXA EDS - 508 to an external power source and to an external alarm system, and shows you what types of cables you should use for the Conso le port, Ethernet ports, and optical fiber ports.
MOXA EtherDevice S witch Hardware Installation Guide 3 - 2 Wiring Requirements War n ing Do not disconnect modules or wires unless power has been switched off or the area is known to be nonhazardous. The devices may only be connected to the supply voltage shown on the type plate.
Install in g MOXA EtherDevice S witch MOXA EtherDevice S witch Hardware Installation Guide 3 - 3 You should also pay attention to the following items : ? ? Use separate paths to route wiring for power and devices. If power wiring and device wiring paths must cross, make sure the wires are perpendicular at the intersection point.
MOXA EtherDevice S witch Hardware Installation Guide 3 - 4 Wiring the Relay Contact EDS - 508 has two sets of relay output — relay 1 and relay 2 . Each Relay Contact consists of the two contacts of the terminal block on EDS - 508 ’ s top panel.
Install in g MOXA EtherDevice S witch MOXA EtherDevice S witch Hardware Installation Guide 3 - 5 Wiring the Redun dant Power Inputs EDS - 508 has two sets of power input — power input 1 and power input 2.
MOXA EtherDevice S witch Hardware Installation Guide 3 - 6 Wiring the Digital Inputs EDS - 508 has two sets of digital input, DI 1 and DI 2. Each DI consist s of two contacts of the 6 - pin terminal block connector on EDS ’ s top panel , which are used for other device ’ s digital inputs.
Install in g MOXA EtherDevice S witch MOXA EtherDevice S witch Hardware Installation Guide 3 - 7 Communication Connections All models of EDS - 508 have one RJ45 console port (RS - 232 interface), and between six and eight 10/100BaseTX Ethernet ports. Some models also have two 100BaseFX (SC - type connector) fiber ports.
MOXA EtherDevice S witch Hardware Installation Guide 3 - 8 NOTE 1. The pin numbers for male DB9 and DB25 connectors, and hole numbers for female DB9 and DB25 connectors are labeled on the connector . However, the numbers are typically quite small, so you may need to use a magnifying glass to see the numbers clearly.
Install in g MOXA EtherDevice S witch MOXA EtherDevice S witch Hardware Installation Guide 3 - 9 RJ45 (10 - pi n) to DB9 (F) Cable Wiring RJ45 (10 - pin) to DB25 (F) Cable Wiring.
MOXA EtherDevice S witch Hardware Installation Guide 3 - 10 10/100BaseTx Ethernet Port Connection The 10/100BaseTX ports located on MOXA EtherDevice TM S witch ’s front panel are used to connect to Ethernet - enabled devices.
Install in g MOXA EtherDevice S witch MOXA EtherDevice S witch Hardware Installation Guide 3 - 11 RJ45 (8 - pin) to RJ45 (8 - pin) Straight - Through Cable Wiring RJ45 (8 - pin) to RJ45 (8 - pin) Cross - Over Cable Wiring 100BaseFx Ethernet Port Connection The concept behind the SC port and cable is quite straightforward.
MOXA EtherDevice S witch Hardware Installation Guide 3 - 12 (A - to - A and B - to - B, as shown below, or A1 - to - A2 and B1 - to - B2). SC - Port Pinouts.
Install in g MOXA EtherDevice S witch MOXA EtherDevice S witch Hardware Installation Guide 3 - 13 SC - Port to SC - Port Cable Wiring This is Class 1 Laser/LED product.
.
4 4 4 Hardware Overview This chapter is an overview of MOXA EDS - 508 ’s various hardware feature s. The following topics are discussed: ? ? Redundant Power Inputs ? ? Relay Contact s ? ? LED Indica.
MOXA EtherDevice S witch Hardware Installation Guide 4 - 2 Redundant Power Inputs MOXA EDS - 508 has two DC power inputs located on its top panel. For detailed instructions on how to connect the power wires to the terminal block connector, see the Wi ring the Redundant Power Inputs section from Chapter 3.
Hardware Overview MOXA EtherDevice Switch Hardware Installation Guide 4 - 3 LED Indicators The front panel of MOXA EDS - 508 contains several LED indicators.
MOXA EtherDevice S witch Hardware Installation Guide 4 - 4 On FX port’s 100 Mbps is active Blinking Data is being transmitted at 100 Mbps 100M (FX) GREEN Off 100BaseFX port is inactive Auto MDI/MDI .
Hardware Overview MOXA EtherDevice Switch Hardware Installation Guide 4 - 5 ? ? A cross - over cable is used to connect like ports: MDI ? MDI or MD I - X ? MDI - X.
MOXA EtherDevice S witch Hardware Installation Guide 4 - 6 Dual Speed Functionality and Switching MOXA EDS - 508 ’s 10/ 100 Mbps RJ45 switched ports can be configured for 10 Mbps operation, 100 Mbps operation, or to auto - negotiate with the connected device for the fastest data transmission rate supported by both devices.
Hardware Overview MOXA EtherDevice Switch Hardware Installation Guide 4 - 7 Switching and Address Learning MOXA EDS - 508 has an address table that can hold up to 2 K node addresses, which makes it suitable for use with large networks.
MOXA EtherDevice S witch Hardware Installation Guide 4 - 8 Specifications Technology Standards IEEE802.3, 802.3u, 802.3x, 802.1D, 802.1 W, 802.1Q, 802.1p Protocols GVRP, SNMP, DHCP Server/Client, BOOTP, TFTP, NTP Forwarding and Filtering Rate 148800 pps Processing Type Store and Forward Flow Control IEEE802.
Hardware Overview MOXA EtherDevice Switch Hardware Installation Guide 4 - 9 Optical Fiber Distance Single mode fiber for 15 , 40 or 80 km, Multi mode fiber for 2 km Wavelength 1310 nm Min.
MOXA EtherDevice S witch Hardware Installation Guide 4 - 10 Environment Operating Temperature 0 to 60°C (32 to 14 0°F) - 40 to 75°C (for " - T" models) Storage Temperature - 40 to 85°C ( - 40 to 185°F) Ambient Relative Humidity 5% to 95% (non - condensing) Regulatory Approvals Safety UL60950, UL 508, CSA C22.
A A A Service Information This appendix shows you how to contact Moxa for information about this and other products, and how to report problems. ? ? MOXA Internet Services ? ? Problem Report Form ? ? .
MOXA EtherDevice S witch Hardware Installation Guide A - 2 MOXA Internet Services Customer satisfaction is our number one concern, and to ensure that customers receive the full benefit of our products, Moxa Internet Services has been set up to provide technical suppo rt, driver updates, product information, and user’s manual updates.
Service Information MOXA EtherDevice Switch Hardware Installation Guide A - 3 Problem Report Form MOXA EDS - 508 Series Customer name: Company: Tel: Fax: Email: Date: 1.
MOXA EtherDevice S witch Hardware Installation Guide A - 4 Return Procedure For product repair, exchange, or refund, the customer must: ? ? Provide evidence of original purchase. ? ? Obtai n a Product Return Agreement (PRA) from the sales representative or dealer.
デバイスMoxa Technologies EDS-508の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Moxa Technologies EDS-508をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはMoxa Technologies EDS-508の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Moxa Technologies EDS-508の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Moxa Technologies EDS-508で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Moxa Technologies EDS-508を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はMoxa Technologies EDS-508の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Moxa Technologies EDS-508に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちMoxa Technologies EDS-508デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
