MTDメーカー551の使用説明書/サービス説明書
ページ先へ移動 of 20
Edger Models 520 5 5 0 5 5 1 Oper ator’ s Man ual IMPOR T ANT : READ SAFETY R ULE S AND INSTR UCTIONS CAREFULL Y MTD LLC, P .O . BO X 361131 CLEVELAND , OH IO 44136-0019 Warning: This unit is equipp.
2 TABLE OF CONTENTS FINDING MODEL NUMBER This Operator’s Manual is an import ant part of your new lawn mower. It will help you asse mble, prepare and maintain the unit fo r best performance.
3 SECTION 1: IMPORTANT SAFE OPERATION PRACTICES WARNING: THIS SYMBOL POINTS OUT IMPORTANT SAFETY INSTRUCTIONS WHICH, IF NOT FOLLOWED, COULD ENDA NGER THE PERSONAL SAFE TY AND/OR PROPER TY OF YOURSELF AND OTHERS. READ AND FOLLOW ALL INSTRUCTIONS IN THIS MANUAL BEFORE ATTEMPTING TO OPERATE THIS MACHINE.
4 4. Never operat e with damaged safety devices. Failure to do so, can resu lt in personal injury. 5. Never run an engi ne indoors or in a poorly ventilated area. Engine exhaust contains carbon monoxide, an odo rless and deadly gas. 6. Do not op erate machin e while under th e influence of alcohol or drugs.
5 SECTION 2: ASSEMBLING YOUR EDGER IMPORT ANT: This unit is shipped WITHOUT GASOLINE or OI L. After setting up the unit, service engine with gasoline and oil as instr ucted in the separate engine manual packed with your unit. NOTE: Reference to right or left hand sid e of t he e dger is observed from the opera ting position.
6 SECTION 3: KNOW YOUR EDGER Figure 4 WARNING: Be familiar wi th all controls and their proper opera tion. Know how to stop the machi ne and disengage t hem quickly. NOTE: Refer to the En gine Manual packed with your edger for a detailed description of all engine-relat ed controls and components.
7 SECTION 4: OPERATING YOUR EDGER The operation of an y edger can result in foreign object s being thrown into the eyes, which ca n result in severe eye damage.
8 SECTION 5: MAKING ADJUSTMENTS Bevel Adjustment (models so equipped) NOTE: Edger features var y by model. All edger models do NOT com e equipped f or blade tilt ad justment nor is there a blade tilt kit available to modify your edger if it was not purchased equ ipped to do so.
9 • Remove the spindle sh eaves belt guard by removing t he two se lf-tappi ng s crews which secure it to the blade plate assemb ly. See Figure 9. Figure 9 • Use two wrenches (one wrench to pr eve.
10 • Lower the righ t, rear wheel by m oving the curb height adjustm ent lever s lightly to the left. See Figure 12. Figure 12 • Pivot the right, rear wheel into an applicable position in relation to the height of the curb to be edged along. • Release the curb height adjustment lever to lock the wheel in po sition.
11 • With your othe r hand, carefully reach under the rear of the unit and re move the belt from around the engine flywheel pulley. • Remove the spindle sh eaves belt guard by removing t he two se lf-tappi ng s crews which secure it to the blade plate assemb ly.
12 SECTION 7: OFF-SEASON STORAGE Observe the following whe n preparing the edger for long-term storage : • Clean and lubricate uni t thoroughly as instructed on page 10 of this manual. • Refer to the Eng ine Manual packed separately with the edger for engin e manufacturers’s storage instructions.
13 REF . NO . PA R T NO . DESCRIPTION 1 710-3103 Screw, 5/16-18 2 710-0449 Screw, 5/16-18 3 710-1205 Eye Bolt 4 710-3008 Screw, 5/16-18 5 710-0606 Screw 6 712-3004A Hex Lock Nut, 5/16-18 7 720-0279 Wing Nut 8 720-0142 Grip 9 720-0241 Wing Knob 10 732-0369 Compression Spring 11 736-0451 Saddle Washer,.
14 REF . NO . PA R T NO . DESCRIPTION 1 710-0191 Screw, 3/8-24 2 710-0599 Screw, 1/4-20 3 710-0654A Screw, 3/8-16 4 710-0944 Screw, 3/8-16 5 712-0431 Flange Lock Nut, 3/8-16 6 731-04168 Debris Guard 7 736-0320 Flat Washer, 3/8 ID x 1.37 OD 8 736-0452 Bell Washer,.
15 REF . NO . PA R T NO . DESCRIPTION 1 687-02019 Blade Plate Assembly 2 710-0395 Hex Screw, 5/16-18 3 710-0599 Self-tapping Screw, 1/4-20 4 710-1143A Hex Screw, 5/8-18 5 711-1017 Clevis Pin 6 712-300.
16 REF . NO . PA R T NO . DESCRIPTION 1 687-02019 Blade Plate Assembly 2 710-0395 Hex Screw, 5/16-18 3 710-0599 Self-tapping Screw, 1/4-20 4 710-1143A Hex Screw, 5/8-18 5 712-3004A Hex Lock Nut, 5/16-.
17 REF . NO . PA R T NO . DESCRIPTION 1 712-0431 Flange Lock Nut, 3/8-16 2 732-04045 Torsion Spring 3 734-1987 Wheel 8x1.8 4 734-1988 Wheel 7x1.8 5 738-04037 Shoulder Screw,.50 x 9.36, 3/8-16 6 738-04038 Shoulder Screw,.50 x 12.90, 3/8-16 7 738-04039 Shoulder Screw,.
18 Model 550 And 551 Wheel Assembly REF . NO . PA R T NO . DESCRIPTION 1 687-02022 Curb Height Adjustment Lever 2 712-0431 Flange Lock Nut, 3/8-16 3 732-04045 Torsion Spring 4 734-1987 Wheel 8x1.8 5 734-1988 Wheel 7x1.8 6 736-0182 Spring Washer,.500 x 1.
19 NOTES.
MANUF A CTURER’S LIMITED W ARRANTY FOR: The limited warranty set forth below is given by MTD LLC with respect to new merchandise purchased and used in the United States, its poss essions and territo ries.
デバイスMTD 551の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
MTD 551をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはMTD 551の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。MTD 551の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。MTD 551で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
MTD 551を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はMTD 551の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、MTD 551に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちMTD 551デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
