MTDメーカーE760の使用説明書/サービス説明書
ページ先へ移動 of 28
IMPOR T ANT : READ SAFETY R ULES AND INSTR UCTIONS CAREFULL Y MTD PR ODUCTS INC. P .O . BO X 368022 CLEVELAND , OHIO 44136-9722 MODELS E740 E760 Warning: This unit is equipped with an internal combust.
2 SECTION 1: IMPORTANT SAFE OPERATION PRACTICES WARNING: THIS SYMBOL POINTS OUT IMPORTANT SAFETY INSTRUCTIONS WHICH, IF NOT FOLLOWED, COULD ENDANGER THE PERSONAL SAFETY AND/OR PROPERTY OF YOURSELF AND OTHERS. READ AND FOLLOW ALL INSTRUCTIONS IN THIS MANUAL BEFORE ATTEMPTING TO OPERATE YOUR SNOW THROWER.
3 • If the snow thrower should start to vibrate abnormally, stop the engine and check immediately for the cause. Vibration is generally a warning of trouble. • Stop engine whenever you leave the operating position, before unclogging the collector/impeller housing or discharge guide, and making any repairs, adjustments, or inspections.
4 SECTION 2: FINDING YOUR MODEL NUMBER This Operators Manual is an important part of your new snow thrower. It will help you assemble, prepare and maintain your snow thrower.
5 SECTION 4: CONTENTS OF HARDWARE PACK La y out the hardw are according to the illustration for identification purposes. P ar ts are illustrated appro ximately one-half size . P ar t numbers are shown in parentheses . (Hardware pac k may contain e xtra items which are not used on your unit.
6 SECTION 5: ASSEMBLY INSTRUCTIONS NO TE: Ref erence to right or left side of the snow thro wer can be determined from behind the unit in the operating position. Figure 2 Figure 3 Figure 4 UNP A CKING 1. Remove staples or break glue on the top flaps of the carton.
7 Figure 5 Figure 6 Figure 7 Figure 8 A TT A CHING THE CHUTE ASSEMBL Y (Hard ware B) 1. Place chute assembly over chute opening, with the opening in the chute assembly facing the front of the unit. 2. Place chute flange keepers beneath lip of chute assembly with the flat side down.
8 IMPORTANT: Attach the shift rod and clutch cables as follows. THEN CHECK THE ADJUSTMENTS AS INSTRUCTED, AND MAKE ANY FINAL ADJUSTMENTS NECESSARY BEFORE OPERATING YOUR SNOW THROWER. Failure to follow the instructions may cause damage to the snow thrower.
9 4. Attach track control cable to track control handle by inserting cable ball into slot on track control handle. Pull cable down and up until it snaps into front of track control handle. Repeat on other side. 5. Secure the track control cables to the inside of the lower handle using the cable ties provided.
10 SECTION 6: CONTROLS Figure 14 SHIFT LEVER (See figure 14) The shift lever is located in the center of the handle panel. The shift lever may be moved into one of eight positions. Run engine with throttle in the fast position. Use the shift lever to determine ground speed.
11 SECTION 7: OPERATION GAS AND OIL FILL-UP Service the engine with gasoline and oil as instructed in the separate engine manual packed with your snow thrower. Read instructions carefully. WARNING: Ne v er fill fuel tank indoors, with engine running or while engine is hot.
12 T O ST OP ENGINE 1. Run engine for a few minutes before stopping to help dry off any moisture on the engine. 2. To help prevent possible freeze-up of starter, proceed as follows. Connect power cord to switch box on engine, then to 120 volt AC receptacle.
13 SECTION 8: ADJUSTMENTS WARNING: NEVER attempt to clean chute or make an y adjustments while engine is running. CHUTE ASSEMBL Y ADJUSTMENT The distance snow is thrown can be adjusted by adjusting the angle of the chute assembly. Refer to the Control section of this manual.
14 SECTION 9: LUBRICATION WARNING: Disconnect the spark plug wire and ground a gainst the engine before perf orming any lubrication or maintenance. ENGINE Refer to engine manual for all engine lubrication instructions.
15 SECTION 10: MAINTENANCE WARNING: Disconnect the spark plug wire and ground a gainst the engine before perf orming any repairs or maintenance. A UGER BEL TS 1. Remove the plastic belt cover on the front of the engine by removing the two self-tapping screws.
16 Figure 22 CHANGING THE FRICTION WHEEL RUBBER The rubber on the friction wheel is subject to wear and should be checked after 25 hours of operation, and periodically thereafter. Replace the friction wheel rubber if any signs of wear or cracking are found.
17 SECTION 11: OFF-SEASON STORAGE WARNING: Never store engine with fuel in tank indoors or in poorl y ventilated areas, where fuel fumes may reach an open flame, spark or pilot light as on a furnace, water heater , clothes dryer or other gas appliance.
18 SECTION 12: TROUBLE SHOOTING GUIDE For repairs beyond the minor adjustments above, contact your local authorized service dealer. T rouble P ossible Cause(s) Corrective Action Engine f ails to star t Fuel tank empty , or stale fuel. Block ed fuel line.
19 Gear Assembly Ref. No. Part No. Description Qty . Ref. No. Part No. Description Qty . 1 618-0123 Housing-L.H. 1 11 721-0327 Seal-Oil 1 2 618-0124 Housing-R.
20 Handle Assembly.
21 Handle Assembly Ref. No. P art No. Description Qty . Ref. No. P art No. Description Qty . 1 684-0008 Arm-Shift 1 34 741-0475 Bushing-Plastic 1 3 684-0103 P anel-Handle 1 35 747-0798A Rod-Shift 1 4 684-0036 Handle-Engagement-R.H. 1 36 747-0877 Rod-Cam 2 5 684-0037 Handle-Engagement-L.
22 Blower Housing 26’’ Ref. No. Part No. Description Qty . Ref. No. Part No. Description Qty . 1 05931 Housing-Bearing 1 19 731-1379 Adapter-Chute 1 2 605-5193 Spiral Assemb ly-L.
23 Track and Frame.
24 Track and Frame.
25 Track and Frame Ref. No. P art No. Description Qty . Ref. No. P art No. Description Qty . 1 611-0053 Axle Assembly 2 45 732-0209 Spring 2 2 618-0043 Dog Assembly-R.
26 Engine and V-Belts Ref. No. Part No. Description Qty . Ref. No. Part No. Description Qty . 1 05896A Brac ket-Idler 1 17 736-0331 W asher-Bell 1 2 629-0071 Cord-Extension 110V 1 18 736-0505 W asher-.
27 George.
28 MANUF A CTURER’S LIMITED W ARRANTY FOR: For TWO YEARS from the date of retail purchase within the United States of America, its possessions and territories, MTD PRODUCTS INC will, at its option, repair or replace, for the original purchaser, free of charge, any part or parts found to be defective in material or workmanship.
デバイスMTD E760の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
MTD E760をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはMTD E760の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。MTD E760の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。MTD E760で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
MTD E760を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はMTD E760の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、MTD E760に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちMTD E760デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
