Multi-Tech SystemsメーカーMTS2SA-T-Rの使用説明書/サービス説明書
ページ先へ移動 of 181
MultiConnect Adapter Serial-to-Serial Adapter with IP User Guide.
Multi-Tech Systems, Inc. MultiConnect Adapte rs User Guide (S000344B) 2 MultiConnect Adapter User Guide Serial-to-Serial Adapter (MTS2SA-T & MTS2SA-T-R) PN S000354A, Version A Copyright This publication may not b e reproduced, in whole or in part, without prior e xpressed written permi ssion from Multi-Tech S ystems, Inc.
Table of Contents Multi-Tech Systems, Inc. MultiConnect Seri al-to-Serial Adapter User Guide (S000354A) 3 Table of Contents Chapter 1 – Product Description & Speci fications .......................................................................
Table of Contents Multi-Tech Systems, Inc. MultiConnect Seri al-to-Serial Adapter User Guide (S000354A) 4 Chapter 10 – Modem Mode AT Commands , S-R egisters, Result Codes ............................................. 85 Escape Code Sequence +++ ....
Table of Contents Multi-Tech Systems, Inc. MultiConnect Seri al-to-Serial Adapter User Guide (S000354A) 5 Chapter 14 – POP3 Client ....................................................................................................... ..............
Chapter 1 – Product Description a nd Specifications Multi-Tech Systems, Inc. MultiConnect Seri al-to-Serial Adapter User Guide (S000354A) 6 Chapter 1 – P roduct Descript ion & Specif icat ions.
Chapter 1 – Product Description a nd Specifications Multi-Tech Systems, Inc. MultiConnect Seri al-to-Serial Adapter User Guide (S000354A) 7 T y pes of Adapters A v ailable Product Adapter Descriptio.
Chapter 1 – Product Description a nd Specifications Multi-Tech Systems, Inc. MultiConnect Seri al-to-Serial Adapter User Guide (S000354A) 8 Specif icat ions Category Description Memory 8 MEG Flash M.
Chapter 1 – Product Description a nd Specifications Multi-Tech Systems, Inc. MultiConnect Seri al-to-Serial Adapter User Guide (S000354A) 9 Category Description Intelligent Features High performance.
Chapter 1 – Product Description a nd Specifications Multi-Tech Systems, Inc. MultiConnect Seri al-to-Serial Adapter User Guide (S000354A) 10 LED Indicators Name Description ACT Activity – Lit when data is being transmi tted or received. STS Status – Blinks to indicate that the unit is functioning.
Chapter 2 – Installation Multi-Tech Systems, Inc. MultiConnect Seri al-to-Serial Adapter User Guide (S000354A) 11 Chapter 2 – Instal lat ion A tt aching t he Mult iConnect to a Fixed Locat ion The MultiConnect adapter is design to be use d on the desktop or to be panel-mounted.
Chapter 2 – Installation Multi-Tech Systems, Inc. MultiConnect Seri al-to-Serial Adapter User Guide (S000354A) 12 Serial-to-Ser ial Adapter Instal lat ion Conne ct ing the Cables Serial-to-Serial Adapter Front Back shown with External Power Option 1.
Chapter 2 – Installation Multi-Tech Systems, Inc. MultiConnect Seri al-to-Serial Adapter User Guide (S000354A) 13 Conne ct ing the P ow er The adapters are powered in one of two ways: • Through the DSR Pin of the RS-232 Cable Adapters powered this way are shipped with an RS -232 cable that has a power pin instead of a DSR pin.
Chapter 3 – Managing an d Configuring the MultiConnect Adapter Multi-Tech Systems, I nc. MultiConnect Serial-to-Serial A dapter User Guide (S000354A) 14 Chapter 3 – Manag ing and Conf ig ur ing the Mult iConne ct Adapter T w o W a ys to Log in Login Using TTY • Use TTY to configure your MultiConnect IP for the first time.
Chapter 4 – Command Li ne Interface (CLI) Multi-Tech Systems, I nc. MultiConnect Serial-to-Serial A dapter User Guide (S000354A) 15 Chapter 4 – Command Line Inter f ac e (CLI) The MultiConnect commands are grouped based on the functionality.
Chapter 4 – Command Li ne Interface (CLI) Multi-Tech Systems, I nc. MultiConnect Serial-to-Serial A dapter User Guide (S000354A) 16 General Commands – Setup General Setup Commands General setup of a MultiConnect IP is port-in depend ent (physical S0, S1 etc.
Chapter 4 – Command Li ne Interface (CLI) Multi-Tech Systems, I nc. MultiConnect Serial-to-Serial A dapter User Guide (S000354A) 17 General Commands – Setup Command Syntax reset modem Description At will, reset the built-in modem. Default Value NA Success OK Error 1.
Chapter 4 – Command Li ne Interface (CLI) Multi-Tech Systems, I nc. MultiConnect Serial-to-Serial A dapter User Guide (S000354A) 18 General Commands – Setup Command Syntax user password <usernam e> <new password> Description Change the p assword for a user.
Chapter 4 – Command Li ne Interface (CLI) Multi-Tech Systems, I nc. MultiConnect Serial-to-Serial A dapter User Guide (S000354A) 19 General Commands – Setup Command Syntax set login Description Prompts the Login for the command sh ell when enabled, and doesn't when disabled.
Chapter 4 – Command Li ne Interface (CLI) Multi-Tech Systems, I nc. MultiConnect Serial-to-Serial A dapter User Guide (S000354A) 20 General Commands – Setup Command Syntax show buildrun Description Command Line Configuration - Histo ry. Upon invoking any comm and, either through Telnet or Serial TTY, the command is added to the buildrun file.
Chapter 4 – Command Li ne Interface (CLI) Multi-Tech Systems, I nc. MultiConnect Serial-to-Serial A dapter User Guide (S000354A) 21 General Commands – Show Command Syntax show statistics Description Displays MultiConnect IP statistics. Default Value NA Success OK Error 1.
Chapter 4 – Command Li ne Interface (CLI) Multi-Tech Systems, I nc. MultiConnect Serial-to-Serial A dapter User Guide (S000354A) 22 General Commands – Show Command Syntax show users Description Displays the configured us ers. Default Value NA Success OK Error 1.
Chapter 4 – Command Li ne Interface (CLI) Multi-Tech Systems, I nc. MultiConnect Serial-to-Serial A dapter User Guide (S000354A) 23 IP Commands – Setup IP Set up Commands Command Syntax set ip dns <enable/disable> Description Enables/disables the DNS client.
Chapter 4 – Command Li ne Interface (CLI) Multi-Tech Systems, I nc. MultiConnect Serial-to-Serial A dapter User Guide (S000354A) 24 IP Commands – Setup Command Syntax set ip syslogd-server <ip addr> Description Sets the remote syslog server's IP address.
Chapter 4 – Command Li ne Interface (CLI) Multi-Tech Systems, I nc. MultiConnect Serial-to-Serial A dapter User Guide (S000354A) 25 IP Commands – Setup Command Syntax set ip telnet auto-dialout <en able/disable> Description Enables Telnet connectivity between the MultiConnect IP and the remote device.
Chapter 4 – Command Li ne Interface (CLI) Multi-Tech Systems, I nc. MultiConnect Serial-to-Serial A dapter User Guide (S000354A) 26 IP Commands – Setup Command Syntax set ip telnet inactivity-timeout <t secs> Description If the Telnet session is inactive for ‘t’ secs, the connection is termin ated.
Chapter 4 – Command Li ne Interface (CLI) Multi-Tech Systems, I nc. MultiConnect Serial-to-Serial A dapter User Guide (S000354A) 27 Serial Commands – Setup Serial Set up Commands Command Syntax set serial auto-telnet <enable/disable> Description This command globally enable s serial auto dial-in support.
Chapter 4 – Command Li ne Interface (CLI) Multi-Tech Systems, I nc. MultiConnect Serial-to-Serial A dapter User Guide (S000354A) 28 Serial Commands – Setup Command Syntax hangup [serial interface] Valid serial interface – Modem port S1 Description When this command is issued, the established live link is brought down.
Chapter 4 – Command Li ne Interface (CLI) Multi-Tech Systems, I nc. MultiConnect Serial-to-Serial A dapter User Guide (S000354A) 29 Serial Commands – Setup Command Syntax set serial [s0] auto-dialin <enable/disable> Description Enables/disables the device port to Internet connectivi ty for the serial port S0.
Chapter 4 – Command Li ne Interface (CLI) Multi-Tech Systems, I nc. MultiConnect Serial-to-Serial A dapter User Guide (S000354A) 30 Serial Commands – Setup Command Syntax set serial [s0] auto-dialin-port [port _num] Description Command to specify the auto dial-in port number.
Chapter 4 – Command Li ne Interface (CLI) Multi-Tech Systems, I nc. MultiConnect Serial-to-Serial A dapter User Guide (S000354A) 31 Serial Commands – Setup Command Syntax set serial [s0] auto-dialin trig -mode <char/ dtr/ dtr-char/ none> Description This mode is applicable onl y when auto dial-in is enabled on the serial port S0.
Chapter 4 – Command Li ne Interface (CLI) Multi-Tech Systems, I nc. MultiConnect Serial-to-Serial A dapter User Guide (S000354A) 32 Serial Commands – Setup Command Syntax set serial [s0] auto-dialout-po rt <port_num> Description If auto-dialout is enabled, specifies the auto dialout-po rt on which the client can co nnect.
Chapter 4 – Command Li ne Interface (CLI) Multi-Tech Systems, I nc. MultiConnect Serial-to-Serial A dapter User Guide (S000354A) 33 Serial Commands – Setup Command Syntax set serial [s0/s1] buffer-data size <0/d bytes> Description This command primarily bu ffers the data.
Chapter 4 – Command Li ne Interface (CLI) Multi-Tech Systems, I nc. MultiConnect Serial-to-Serial A dapter User Guide (S000354A) 34 Serial Commands – Setup Command Syntax set serial [s0/s1] chat-script <line- num> <e xpect-stri ng> <send-string> Description Sets expect and send strings for the chat script to act on the modem.
Chapter 4 – Command Li ne Interface (CLI) Multi-Tech Systems, I nc. MultiConnect Serial-to-Serial A dapter User Guide (S000354A) 35 Serial Commands – Setup Command Syntax Set serial [s0/s1] flow-control <no ne/rts-cts> Description Set the flow-control of the serial port .
Chapter 4 – Command Li ne Interface (CLI) Multi-Tech Systems, I nc. MultiConnect Serial-to-Serial A dapter User Guide (S000354A) 36 Serial Commands – Setup Command Syntax set serial [s0/s1] modem dial-prefix <dialprefix > Description Sets the Modem Dial-Prefix.
Chapter 4 – Command Li ne Interface (CLI) Multi-Tech Systems, I nc. MultiConnect Serial-to-Serial A dapter User Guide (S000354A) 37 Serial Commands – Setup Command Syntax set serial [s1] modem diali ng-trig-mode <none/dtr/command> Description Sets the dialing trigger mode for the modem po rt S1.
Chapter 4 – Command Li ne Interface (CLI) Multi-Tech Systems, I nc. MultiConnect Serial-to-Serial A dapter User Guide (S000354A) 38 Serial Commands – Setup Command Syntax set serial [s0/s1] modem ini t-string <init-num > <init-str> Description Configures the modem initial strings.
Chapter 4 – Command Li ne Interface (CLI) Multi-Tech Systems, I nc. MultiConnect Serial-to-Serial A dapter User Guide (S000354A) 39 Serial Commands – Setup Command Syntax set serial [s0] login-string <login-string> Description Sets a login-string to the serial port.
Chapter 4 – Command Li ne Interface (CLI) Multi-Tech Systems, I nc. MultiConnect Serial-to-Serial A dapter User Guide (S000354A) 40 Serial Commands – Setup Command Syntax set serial [s0/s1] stop-bits <1/1.5/2> Description Sets the stop bits.
Chapter 4 – Command Li ne Interface (CLI) Multi-Tech Systems, I nc. MultiConnect Serial-to-Serial A dapter User Guide (S000354A) 41 Serial Commands – Show Command Syntax show serial [s0/s1] statistics Description Displays Serial S tatistics.
Chapter 4 – Command Li ne Interface (CLI) Multi-Tech Systems, I nc. MultiConnect Serial-to-Serial A dapter User Guide (S000354A) 42 PPP Commands – Setup PPP Set up Commands Note: All PPP Commands use the ppp0 interface, which corresp onds to the modem port S1.
Chapter 4 – Command Li ne Interface (CLI) Multi-Tech Systems, I nc. MultiConnect Serial-to-Serial A dapter User Guide (S000354A) 43 PPP Commands – Setup Command Syntax set ppp <interface> diali ng-max-retries <0-100> Description Configures the maximum number of dialing retri es.
Chapter 4 – Command Li ne Interface (CLI) Multi-Tech Systems, I nc. MultiConnect Serial-to-Serial A dapter User Guide (S000354A) 44 PPP Commands – Setup Command Syntax set ppp <interface> local -ip-addr <ipaddr> mask <ipmask> Description During IPCP negotiations, t he configured IP address i s sent for the local interface.
Chapter 4 – Command Li ne Interface (CLI) Multi-Tech Systems, I nc. MultiConnect Serial-to-Serial A dapter User Guide (S000354A) 45 PPP Commands – Show Command Syntax show ppp ppp0 con figuration .
Chapter 4 – Command Li ne Interface (CLI) Multi-Tech Systems, I nc. MultiConnect Serial-to-Serial A dapter User Guide (S000354A) 46 PPP Commands – Show Command Syntax show ppp <interface> statistics Description Displays PPP Statistics. Default Value - Success OK Error 1.
Chapter 4 – Command Li ne Interface (CLI) Multi-Tech Systems, I nc. MultiConnect Serial-to-Serial A dapter User Guide (S000354A) 47 HTTP Server Commands – Setup HT T P Ser ver Commands The commands in this section are listed in the order in which they might be used.
Chapter 4 – Command Li ne Interface (CLI) Multi-Tech Systems, I nc. MultiConnect Serial-to-Serial A dapter User Guide (S000354A) 48 HTTP Server Commands – Setup Command Syntax save param Description Invoking this command will save the ho st parameters into the flash.
Chapter 4 – Command Li ne Interface (CLI) Multi-Tech Systems, I nc. MultiConnect Serial-to-Serial A dapter User Guide (S000354A) 49 SMTP Client Commands – Setup SMTP Client C ommand s The commands in this section are listed in the order in which they might be used.
Chapter 4 – Command Li ne Interface (CLI) Multi-Tech Systems, I nc. MultiConnect Serial-to-Serial A dapter User Guide (S000354A) 50 SMTP Client Commands – Setup Command Syntax set send-mail to-address <n > <email-address> where n = 1 to 5.
Chapter 4 – Command Li ne Interface (CLI) Multi-Tech Systems, I nc. MultiConnect Serial-to-Serial A dapter User Guide (S000354A) 51 SMTP Client Commands – Setup Command Syntax send-mail [-b] [-t <email-address1, email-address2, ...>] [-c <email-address1, email-address2, .
Chapter 4 – Command Li ne Interface (CLI) Multi-Tech Systems, I nc. MultiConnect Serial-to-Serial A dapter User Guide (S000354A) 52 POP3 Client Commands – Setup POP3 Client Commands Command Syntax.
Chapter 4 – Command Li ne Interface (CLI) Multi-Tech Systems, I nc. MultiConnect Serial-to-Serial A dapter User Guide (S000354A) 53 POP3 Client Commands – Setup Command Syntax set recv-mail leave-.
Chapter 4 – Command Li ne Interface (CLI) Multi-Tech Systems, I nc. MultiConnect Serial-to-Serial A dapter User Guide (S000354A) 54 POP3 Client Commands – Setup Command Syntax recv-mail top <index> <n> Description Displays the first <n> lines of the mail co rresponding to index.
Chapter 4 – Command Li ne Interface (CLI) Multi-Tech Systems, I nc. MultiConnect Serial-to-Serial A dapter User Guide (S000354A) 55 FTP Client Commands – Setup FTP Client C ommands Command Syntax .
Chapter 4 – Command Li ne Interface (CLI) Multi-Tech Systems, I nc. MultiConnect Serial-to-Serial A dapter User Guide (S000354A) 56 FTP Client Commands – Setup Command Syntax ftp < [-l] [-t] [-.
Chapter 4 – Command Li ne Interface (CLI) Multi-Tech Systems, I nc. MultiConnect Serial-to-Serial A dapter User Guide (S000354A) 57 SNTP Client Commands – Setup SN T P C lient Commands Command Syn.
Chapter 4 – Command Li ne Interface (CLI) Multi-Tech Systems, I nc. MultiConnect Serial-to-Serial A dapter User Guide (S000354A) 58 SNTP Client Commands – Setup Command Syntax set sntp-client polling-time <value > where value = 2 to 1440 Description Sets the polling time at which SNTP clie nt request s the server to update the time.
Chapter 4 – Command Li ne Interface (CLI) Multi-Tech Systems, I nc. MultiConnect Serial-to-Serial A dapter User Guide (S000354A) 59 SNTP Client Commands – Setup Command Syntax set sntp-client daylight-saving start-week day <dayofweek> where dayofweek = sunday, monday .
Chapter 4 – Command Li ne Interface (CLI) Multi-Tech Systems, I nc. MultiConnect Serial-to-Serial A dapter User Guide (S000354A) 60 SNTP Client Commands – Setup Command Syntax set sntp-client dayl.
Chapter 5 – Setting Country or Region Codes Using the CLI Multi-Tech Systems, I nc. MultiConnect Serial-to-Serial A dapter User Guide (S000354A) 61 Chapter 5 – Sett ing Count r y or R eg ion Codes Using the CLI The Default Country or Region Code is B5.
Chapter 6 – Prerequisite Config urations Multi-Tech Systems, I nc. MultiConnect Serial-to-Serial A dapter User Guide (S000354A) 62 Chapter 6 – P rer equisite Conf ig ur at ions This chapter covers prerequisite tasks, those tasks or configurations that must be completed before you can set up certain operating scena rios.
Chapter 6 – Prerequisite Config urations Multi-Tech Systems, I nc. MultiConnect Serial-to-Serial A dapter User Guide (S000354A) 63 2. MultiConne ct IP Modes of Operation The MultiConnect IP can function in two modes: • Transparent Mode When the MultiConnect IP is configured to function in the modem operation mode, it functions as a modem.
Chapter 6 – Prerequisite Config urations Multi-Tech Systems, I nc. MultiConnect Serial-to-Serial A dapter User Guide (S000354A) 64 3. Phy sical Link Established over the Modem Port For any application such as SMTP Client, HTTP Se rver, POP3 Client, etc.
Chapter 7 – Telnet Dialout Multi-Tech Systems, I nc. MultiConnect Serial-to-Serial A dapter User Guide (S000354A) 65 Chapter 7 – T elnet Dialout Int roduction Telnet Dialout Feature The Telnet feature allows you to access the serial po rt and estab lish two-way traffic between the Telnet/RAW-TCP client and the serial d evice.
Chapter 7 – Telnet Dialout Multi-Tech Systems, I nc. MultiConnect Serial-to-Serial A dapter User Guide (S000354A) 66 Optional Configuration Commands (Return to Scenario 1 - Setup Manual Di alout Not.
Chapter 7 – Telnet Dialout Multi-Tech Systems, I nc. MultiConnect Serial-to-Serial A dapter User Guide (S000354A) 67 Sc enario 1 – Manu al Dialout Connect to the MultiConnect IP using a Tel net Client on po rt 23 (c onfiguration port). At the command prompt, invoke # dialout serial s0 .
Chapter 7 – Telnet Dialout Multi-Tech Systems, I nc. MultiConnect Serial-to-Serial A dapter User Guide (S000354A) 68 MultiConnect IP Manual Dialout Setup Commands # set serial s0 stop-bits 1 # set s.
Chapter 7 – Telnet Dialout Multi-Tech Systems, I nc. MultiConnect Serial-to-Serial A dapter User Guide (S000354A) 69 Sc enario 2 – Auto Dialout In this scenario, the Auto Dialout session in Telnet mode is opened usin g a Telnet client. Prerequisites RAW mode (global and each port) MUST BE DISABLED using th e Optional Configuration Commands .
Chapter 7 – Telnet Dialout Multi-Tech Systems, I nc. MultiConnect Serial-to-Serial A dapter User Guide (S000354A) 70 MultiConnect IP Auto Dialout in Telnet Mode Setup Commands # set ip telnet auto-d.
Chapter 7 – Telnet Dialout Multi-Tech Systems, I nc. MultiConnect Serial-to-Serial A dapter User Guide (S000354A) 71 Sc enario 3 – Auto Dialout in R A W Mode In this scenario, the Auto-Dialout session in RAW mode is opened u sing a RAW-TCP client.
Chapter 7 – Telnet Dialout Multi-Tech Systems, I nc. MultiConnect Serial-to-Serial A dapter User Guide (S000354A) 72 Commands to Setup Auto Dial-out in RAW-Mode for MultiConnect IP # set ip telnet a.
Chapter 8 – Auto Dial-in Feature Multi-Tech Systems, I nc. MultiConnect Serial-to-Serial A dapter User Guide (S000354A) 73 Chapter 8 – Auto Dial-in F eature Int roduction The auto dial-in feature .
Chapter 8 – Auto Dial-in Feature Multi-Tech Systems, I nc. MultiConnect Serial-to-Serial A dapter User Guide (S000354A) 74 Sc enario 1 – Manu al Serial Dial-in Login to the Command prchat -scriptompt from the serial si de. Invoke # telnet <ip-address> <port> at the comma nd prompt.
Chapter 8 – Auto Dial-in Feature Multi-Tech Systems, I nc. MultiConnect Serial-to-Serial A dapter User Guide (S000354A) 75 MultiConnect IP Manual Dial-In Setup Commands # set serial s0 baud-rate 115.
Chapter 8 – Auto Dial-in Feature Multi-Tech Systems, I nc. MultiConnect Serial-to-Serial A dapter User Guide (S000354A) 76 Sc enario 2 – Ser ial Auto Dial-in in T elnet Mode This example shows h ow to setup a seri al auto dial-i n session in Telnet mod e.
Chapter 8 – Auto Dial-in Feature Multi-Tech Systems, I nc. MultiConnect Serial-to-Serial A dapter User Guide (S000354A) 77 MultiConnect IP Auto Dial-In Setup in Telnet Mode Commands # set serial auto-telnet enable # set serial s0 auto-dialin enable # set serial s0 auto-dialin trig-mode dtr-char # set serial s0 auto-dialin-ipaddress 202.
Chapter 8 – Auto Dial-in Feature Multi-Tech Systems, I nc. MultiConnect Serial-to-Serial A dapter User Guide (S000354A) 78 Sc enario 3 – Auto Dial-in Ses sion in RA W Mode This scenario shows h ow to configure an auto dial -i n session in RA W mode.
Chapter 8 – Auto Dial-in Feature Multi-Tech Systems, I nc. MultiConnect Serial-to-Serial A dapter User Guide (S000354A) 79 Sc enario 4 – Ser ial Tunneling Mode The scenario shows a se rial tunnel .
Chapter 8 – Auto Dial-in Feature Multi-Tech Systems, I nc. MultiConnect Serial-to-Serial A dapter User Guide (S000354A) 80 Commands for Serial Tunneling Setup Using Two MultiConnec t IP Modules Comm.
Chapter 9 – Modem (Transparent) Mode Multi-Tech Systems, I nc. MultiConnect Serial-to-Serial A dapter User Guide (S000354A) 81 Chapter 9 – Modem (Tr anspar ent) Mode Int roduction In the modem mode (also called transparent mode ), raw data is communicated between serial port s 1 and 2.
Chapter 9 – Modem (Transparent) Mode Multi-Tech Systems, I nc. MultiConnect Serial-to-Serial A dapter User Guide (S000354A) 82 Sc enario 1 – Mult iConnect IP as a Modem In this scenario, once the physical link is up on the built -in modem in terface; i.
Chapter 9 – Modem (Transparent) Mode Multi-Tech Systems, I nc. MultiConnect Serial-to-Serial A dapter User Guide (S000354A) 83 Sc enario 2 – Ser ial Tunneling in Tr ansparent Mode In this scenario.
Chapter 9 – Modem (Transparent) Mode Multi-Tech Systems, I nc. MultiConnect Serial-to-Serial A dapter User Guide (S000354A) 84 Commands for MultiConnect IP - 1 (Dialing End) # set operation-mode mod.
Chapter 10 − Modem Mode AT Commands, S-Registers, an d Result Codes Multi-Tech Systems, I nc. MultiConnect Serial-to-Serial A dapter User Guide (S000354A) 85 Chapter 10 – Modem Mode A T Comm ands , S -Reg isters , R esult Codes This chapter cove rs the V.
Chapter 10 − Modem Mode AT Commands, S-Registers, an d Result Codes Multi-Tech Systems, I nc. MultiConnect Serial-to-Serial A dapter User Guide (S000354A) 86 Command T y pes The following list should help if you are looki ng for a particular type of command.
Chapter 10 − Modem Mode AT Commands, S-Registers, an d Result Codes Multi-Tech Systems, I nc. MultiConnect Serial-to-Serial A dapter User Guide (S000354A) 87 Call Control Commands +MS Modulation Sel.
Chapter 10 − Modem Mode AT Commands, S-Registers, an d Result Codes Multi-Tech Systems, I nc. MultiConnect Serial-to-Serial A dapter User Guide (S000354A) 88 Command Det ail Command: AT Attention Co de Values: n/a Description: The attention code pr ecedes all command li nes except for escape sequen ces.
Chapter 10 − Modem Mode AT Commands, S-Registers, an d Result Codes Multi-Tech Systems, I nc. MultiConnect Serial-to-Serial A dapter User Guide (S000354A) 89 P Select pulse dialin g: pulse dial the numb ers that follow until a "T " is encountered.
Chapter 10 − Modem Mode AT Commands, S-Registers, an d Result Codes Multi-Tech Systems, I nc. MultiConnect Serial-to-Serial A dapter User Guide (S000354A) 90 Command: I n Identification (for V.22bis) This command cause s the modem to reports the requested re sult according to the command parameter.
Chapter 10 − Modem Mode AT Commands, S-Registers, an d Result Codes Multi-Tech Systems, I nc. MultiConnect Serial-to-Serial A dapter User Guide (S000354A) 91 Command: P Set Pulse Dial Default Values: P, T Default: T Description: This command forces pulse d ialing until t he next T dial modif ier of T command is received.
Chapter 10 − Modem Mode AT Commands, S-Registers, an d Result Codes Multi-Tech Systems, I nc. MultiConnect Serial-to-Serial A dapter User Guide (S000354A) 92 Command: X n Extended Re sult Codes and .
Chapter 10 − Modem Mode AT Commands, S-Registers, an d Result Codes Multi-Tech Systems, I nc. MultiConnect Serial-to-Serial A dapter User Guide (S000354A) 93 Command: &F n Restore Fac tory Configuration (Profile ) Values: n = 0 Default: None Description: The modem loads the fact ory default configu ration (profile).
Chapter 10 − Modem Mode AT Commands, S-Registers, an d Result Codes Multi-Tech Systems, I nc. MultiConnect Serial-to-Serial A dapter User Guide (S000354A) 94 Command: &T n Local Analog Loopback Test Values: n = 0, 1, Default: None Description: The modem can perform the local analog l oopback test if &T1 is selected.
Chapter 10 − Modem Mode AT Commands, S-Registers, an d Result Codes Multi-Tech Systems, I nc. MultiConnect Serial-to-Serial A dapter User Guide (S000354A) 95 Command: &V1 Display Last Connection Statistics (&V1 has no functiona lity in V.
Chapter 10 − Modem Mode AT Commands, S-Registers, an d Result Codes Multi-Tech Systems, I nc. MultiConnect Serial-to-Serial A dapter User Guide (S000354A) 96 Command: &Z y=x Store Tele phone Number (Not available in V.
Chapter 10 − Modem Mode AT Commands, S-Registers, an d Result Codes Multi-Tech Systems, I nc. MultiConnect Serial-to-Serial A dapter User Guide (S000354A) 97 Command: N n Operating Mode – Error Correction Values: n = 0–5 Default: 5 Description: Cont rols the pr eferred error-correcti ng mode to be negotiated in a subsequent data connectio n.
Chapter 10 − Modem Mode AT Commands, S-Registers, an d Result Codes Multi-Tech Systems, I nc. MultiConnect Serial-to-Serial A dapter User Guide (S000354A) 98 Command: – Kn MNP Extended Services (Not avail able in V.22bis) Values: n = 0, 1, 2. Default: 0 Description: Enab les or disables conversion of a V.
Chapter 10 − Modem Mode AT Commands, S-Registers, an d Result Codes Multi-Tech Systems, I nc. MultiConnect Serial-to-Serial A dapter User Guide (S000354A) 99 Case 3: Telephone L ine is Not Connecte .
Chapter 10 − Modem Mode AT Commands, S-Registers, an d Result Codes Multi-Tech Systems, I nc. MultiConnect Serial-to-Serial A dapter User Guide (S000354A) 100 Command: %L n Line Signal Level Report Returns a value, which indic ates the received signal lev el.
Chapter 10 − Modem Mode AT Commands, S-Registers, an d Result Codes Multi-Tech Systems, I nc. MultiConnect Serial-to-Serial A dapter User Guide (S000354A) 101 Command: +A 8I CI Signal Indica tion (Not available in V.22bis) This indication is issued b y an answering modem, if + A8E,<v8a> does not equal 0, t o indicate detecti on of a V.
Chapter 10 − Modem Mode AT Commands, S-Registers, an d Result Codes Multi-Tech Systems, I nc. MultiConnect Serial-to-Serial A dapter User Guide (S000354A) 102 Command: +EB Break Handling in Error Control Operation (Not available in V.22b is) Values: n/a Description: This extended-format compou nd parameter controls t he break handling i n V.
Chapter 10 − Modem Mode AT Commands, S-Registers, an d Result Codes Multi-Tech Systems, I nc. MultiConnect Serial-to-Serial A dapter User Guide (S000354A) 103 Command: +ES Error Control Selection De.
Chapter 10 − Modem Mode AT Commands, S-Registers, an d Result Codes Multi-Tech Systems, I nc. MultiConnect Serial-to-Serial A dapter User Guide (S000354A) 104 Command: +ETBM Call Termination Buffer .
Chapter 10 − Modem Mode AT Commands, S-Registers, an d Result Codes Multi-Tech Systems, I nc. MultiConnect Serial-to-Serial A dapter User Guide (S000354A) 105 Command: +IFC DTE-Modem Local Flow Cont.
Chapter 10 − Modem Mode AT Commands, S-Registers, an d Result Codes Multi-Tech Systems, I nc. MultiConnect Serial-to-Serial A dapter User Guide (S000354A) 106 Command: +MR Modulation Reporting Control (Not available in V.
Chapter 10 − Modem Mode AT Commands, S-Registers, an d Result Codes Multi-Tech Systems, I nc. MultiConnect Serial-to-Serial A dapter User Guide (S000354A) 107 Command: +MS Modulation Selection Description: This extended-format compou nd parameter cont rols the manner of operati on of the modulation capabil ities in the modem.
Chapter 10 − Modem Mode AT Commands, S-Registers, an d Result Codes Multi-Tech Systems, I nc. MultiConnect Serial-to-Serial A dapter User Guide (S000354A) 108 Command: +VCID Caller ID (CID) Descript.
Chapter 10 − Modem Mode AT Commands, S-Registers, an d Result Codes Multi-Tech Systems, I nc. MultiConnect Serial-to-Serial A dapter User Guide (S000354A) 109 Command: #UD Last Call Status Report (Not available in V.22bis) Description: #UD is an action command requesting l ogged operatio n events reporting.
Chapter 10 − Modem Mode AT Commands, S-Registers, an d Result Codes Multi-Tech Systems, I nc. MultiConnect Serial-to-Serial A dapter User Guide (S000354A) 110 Notes for AT#UD Tables 1. The modem may insert a dela y (e.g., 10 ms) bet ween information te xt lines.
Chapter 10 − Modem Mode AT Commands, S-Registers, an d Result Codes Multi-Tech Systems, I nc. MultiConnect Serial-to-Serial A dapter User Guide (S000354A) 111 Table 8-4. Multimedia Modes Code Definition 0 Data Only 1 Fax Onl y 2 Voice 9 Video-tele phony, H.
Chapter 10 − Modem Mode AT Commands, S-Registers, an d Result Codes Multi-Tech Systems, I nc. MultiConnect Serial-to-Serial A dapter User Guide (S000354A) 112 Table 8-10. callCleared c odes fro m 3.6.4/V.58-1994 Value Description Notes 0 CauseUn identified Call setup issues 1 No Previous call Not in V.
Chapter 10 − Modem Mode AT Commands, S-Registers, an d Result Codes Multi-Tech Systems, I nc. MultiConnect Serial-to-Serial A dapter User Guide (S000354A) 113 Example Modem Response and Usage Example #UD commen d response are shown in T able 8-11. Table 8-11.
Chapter 10 − Modem Mode AT Commands, S-Registers, an d Result Codes Multi-Tech Systems, I nc. MultiConnect Serial-to-Serial A dapter User Guide (S000354A) 114 F astConne ct Commands Command: $F FastCo nnect Control Description: Allows configur ing of the client modem to connect to a central site mod em that supports non-standar d V.
Chapter 10 − Modem Mode AT Commands, S-Registers, an d Result Codes Multi-Tech Systems, I nc. MultiConnect Serial-to-Serial A dapter User Guide (S000354A) 115 V . 92 Commands (+P and –Q Comm ands) This section describes the +P (PCM DCE) and –Q commands and parameters used t o control the V.
Chapter 10 − Modem Mode AT Commands, S-Registers, an d Result Codes Multi-Tech Systems, I nc. MultiConnect Serial-to-Serial A dapter User Guide (S000354A) 116 Command: +PMHT Modem-on-Hold Timer Description: Controls whether or not the modem will grant or den y a modem-on-hold (MOH) request as well as setting t he MOH Timeout value.
Chapter 10 − Modem Mode AT Commands, S-Registers, an d Result Codes Multi-Tech Systems, I nc. MultiConnect Serial-to-Serial A dapter User Guide (S000354A) 117 Command: +PSS Use Short Sequence Description: Causes a calling modem t o force ei ther a V.
Chapter 10 − Modem Mode AT Commands, S-Registers, an d Result Codes Multi-Tech Systems, I nc. MultiConnect Serial-to-Serial A dapter User Guide (S000354A) 118 S- R egi st e r s This section covers S-Registe r descriptions and their defau lt values (which may be loaded at any time by using the Z command).
Chapter 10 − Modem Mode AT Commands, S-Registers, an d Result Codes Multi-Tech Systems, I nc. MultiConnect Serial-to-Serial A dapter User Guide (S000354A) 119 Register Unit Range Def ault Description S6 seconds 2–255 2 Wait Time Before Blind Dialing or for Dia l Tone.
Chapter 10 − Modem Mode AT Commands, S-Registers, an d Result Codes Multi-Tech Systems, I nc. MultiConnect Serial-to-Serial A dapter User Guide (S000354A) 120 Register Unit Range Def ault Description S14 138 (8Ah) General Bit-Mapped Options Status. Indicates the status of command options.
Chapter 10 − Modem Mode AT Commands, S-Registers, an d Result Codes Multi-Tech Systems, I nc. MultiConnect Serial-to-Serial A dapter User Guide (S000354A) 121 Register Unit Range Def ault Description S22 117 (75h) Speaker/Results Bit-Mapped Options Status.
Chapter 10 − Modem Mode AT Commands, S-Registers, an d Result Codes Multi-Tech Systems, I nc. MultiConnect Serial-to-Serial A dapter User Guide (S000354A) 122 Register Unit Range Def ault Description S27 73 (49Ah) General Bit-Mapped Options Status. Indicates the stat us of command options.
Chapter 10 − Modem Mode AT Commands, S-Registers, an d Result Codes Multi-Tech Systems, I nc. MultiConnect Serial-to-Serial A dapter User Guide (S000354A) 123 Register Unit Range Def ault Description S36 7 L APM Failure Control. T his value indicates what should h appen upon a LAPM failure.
Chapter 10 − Modem Mode AT Commands, S-Registers, an d Result Codes Multi-Tech Systems, I nc. MultiConnect Serial-to-Serial A dapter User Guide (S000354A) 124 Register Unit Range Def ault Description S40 104 (68h) General Bit-Mapped Op tions Status.
Chapter 10 − Modem Mode AT Commands, S-Registers, an d Result Codes Multi-Tech Systems, I nc. MultiConnect Serial-to-Serial A dapter User Guide (S000354A) 125 Register Unit Range Def ault Description S82 3, 7, or 128 128 Break Handling Optio ns (V.22bis only) Break Signals provide a way for the user to get the at tention of the remote modem.
Chapter 10 − Modem Mode AT Commands, S-Registers, an d Result Codes Multi-Tech Systems, I nc. MultiConnect Serial-to-Serial A dapter User Guide (S000354A) 126 Register Unit Range Def ault Description S95 0 Extended Result Codes Control.
Chapter 10 − Modem Mode AT Commands, S-Registers, an d Result Codes Multi-Tech Systems, I nc. MultiConnect Serial-to-Serial A dapter User Guide (S000354A) 127 Result Codes The modem responds to commands from t he DTE and to activi t y on the line by signa ling to the DT E in the form of result codes.
Chapter 10 − Modem Mode AT Commands, S-Registers, an d Result Codes Multi-Tech Systems, I nc. MultiConnect Serial-to-Serial A dapter User Guide (S000354A) 128 Short Form Long Form Description 11 CONNECT 4800 Connected at 4800 bp s and speed reporting enabled.
Chapter 10 − Modem Mode AT Commands, S-Registers, an d Result Codes Multi-Tech Systems, I nc. MultiConnect Serial-to-Serial A dapter User Guide (S000354A) 129 Short Form Long Form Description 59 CONNECT 16800 Connected at 16800 bp s and DTE speed reporting enabled.
Chapter 10 − Modem Mode AT Commands, S-Registers, an d Result Codes Multi-Tech Systems, I nc. MultiConnect Serial-to-Serial A dapter User Guide (S000354A) 130 Short Form Long Form Description 153 * +MRR: 38000 Connected at 38000 b ps. Modem connects to the line at 38000 bps and carrier reporting is enabled.
Chapter 10 − Modem Mode AT Commands, S-Registers, an d Result Codes Multi-Tech Systems, I nc. MultiConnect Serial-to-Serial A dapter User Guide (S000354A) 131 Short Form Long Form Description 187 * CONNECT 41333 Connected at 41333 bp s. Modem connects to the line at 41333 bps and DCE SPEED reporting is enabled.
Chapter 11 – Point-to-Point Protocol Multi-Tech Systems, I nc. MultiConnect Serial-to-Serial A dapter User Guide (S000354A) 132 Chapter 11 – P oint-to-P oint P rotoc ol Int roduction Point-to-Point Protocol (PPP) is the Internet Standard for transmissi on of IP packets over serial links.
Chapter 11 – Point-to-Point Protocol Multi-Tech Systems, I nc. MultiConnect Serial-to-Serial A dapter User Guide (S000354A) 133 Setting Passwords Upon successful execution of this comm and, the MultiConnect IP will return an OK or an error message.
Chapter 11 – Point-to-Point Protocol Multi-Tech Systems, I nc. MultiConnect Serial-to-Serial A dapter User Guide (S000354A) 134 PPP Inter f ac e R elated P ar ameters Enabling/Disabling Authentication This command enables or disables a PPP Authentic ation session .
Chapter 11 – Point-to-Point Protocol Multi-Tech Systems, I nc. MultiConnect Serial-to-Serial A dapter User Guide (S000354A) 135 Serial Inter f ac e R elated P ar ameters Connect Type This command sets the co nnection type. A conne ctio n type can be either a direct connection or a connection through a modem.
Chapter 12 – HTTP Server Multi-Tech Systems, I nc. MultiConnect Serial-to-Serial A dapter User Guide (S000354A) 136 Chapter 12 – HT T P Ser v er Int roduction The HTTP Server on the MultiConnect IP supp orts hosting of embedded Web page s on behalf of the host.
Chapter 12 – HTTP Server Multi-Tech Systems, I nc. MultiConnect Serial-to-Serial A dapter User Guide (S000354A) 137 Set up and Conf ig uration Prerequisite for Enabling the HTTP Server Before being .
Chapter 12 – HTTP Server Multi-Tech Systems, I nc. MultiConnect Serial-to-Serial A dapter User Guide (S000354A) 138 Conf ig uration Modes The embedded HTTP Server on the MultiConn ect IP su pports two configuration modes. This option is available when the http-page is set to serial (se e Mandatory Setup instruct ions).
Chapter 12 – HTTP Server Multi-Tech Systems, I nc. MultiConnect Serial-to-Serial A dapter User Guide (S000354A) 139 Example: P0:temperature:I:1:65535:100 P1:username:S:8:50:M ultiConnect IP Here, P0 and P1 are two parameters , which correspond to the nam es like Temperature & username specified in the HTML page.
Chapter 12 – HTTP Server Multi-Tech Systems, I nc. MultiConnect Serial-to-Serial A dapter User Guide (S000354A) 140 The Embedded HTML Page The embedde d Web pa ge stored on the MultiConnect IP cons ists of normal ASCII text HTML code, which can be genera ted using any HTML editing tool.
Chapter 12 – HTTP Server Multi-Tech Systems, I nc. MultiConnect Serial-to-Serial A dapter User Guide (S000354A) 141 Uploading the Web Page and Parameter List The Host Device Files (.HTML, default parameter Li st ….) can be uploaded to the MultiConne ct IP using TFTP CLIENT.
Chapter 12 – HTTP Server Multi-Tech Systems, I nc. MultiConnect Serial-to-Serial A dapter User Guide (S000354A) 142 Monitoring and Conf ig uring t he Host through a Bro wser If you have successfully.
Chapter 13 – SMTP Client Multi-Tech Systems, I nc. MultiConnect Serial-to-Serial A dapter User Guide (S000354A) 143 Cha pt er 13 – SM TP Cli e n t Int roduction SMTP Client is used to establish a TCP sessi on on a n SMTP server running on port 25.
Chapter 13 – SMTP Client Multi-Tech Systems, I nc. MultiConnect Serial-to-Serial A dapter User Guide (S000354A) 144 Set up and Conf ig uration P rerequisites The following details are mandatory for configuration and have to be validated before sen ding an email: • Host Interaction Mode enabled to restrict Telnet-D ialout and PPP.
Chapter 13 – SMTP Client Multi-Tech Systems, I nc. MultiConnect Serial-to-Serial A dapter User Guide (S000354A) 145 Sc enario 1 – Sending a T e xt Email f rom the Command P rompt Issue the followi.
Chapter 13 – SMTP Client Multi-Tech Systems, I nc. MultiConnect Serial-to-Serial A dapter User Guide (S000354A) 146 Sc enario 2 – Sending a T e xt Email f rom the Inter act iv e Mode Message body .
Chapter 13 – SMTP Client Multi-Tech Systems, I nc. MultiConnect Serial-to-Serial A dapter User Guide (S000354A) 147 Sc enario 3 – Sending a T e xt Email Using Conf ig uration and Interactive Mode • The to-addresses, cc-addresses, and subject taken from the configuration and • The message body is entered in interactive mode.
Chapter 13 – SMTP Client Multi-Tech Systems, I nc. MultiConnect Serial-to-Serial A dapter User Guide (S000354A) 148 Sc enario 4 – Sending a T ex t Email Using No Conf ig uration The to-address , cc-address , and subject are NOT configured in this example .
Chapter 13 – SMTP Client Multi-Tech Systems, I nc. MultiConnect Serial-to-Serial A dapter User Guide (S000354A) 149 Sc enario 5 – Sending a M ime Encoded Binary A tt achment Using Command P rompt The email addresses, subject, and message body are taken from the command prompt.
Chapter 13 – SMTP Client Multi-Tech Systems, I nc. MultiConnect Serial-to-Serial A dapter User Guide (S000354A) 150 Sc enario 6 – Sending a M ime Encoded Binary A ttac hm e nt Usi n g th e C om ma.
Chapter 13 – SMTP Client Multi-Tech Systems, I nc. MultiConnect Serial-to-Serial A dapter User Guide (S000354A) 151 Sc enario 7 – Sending a M ime Encoded Binary A tt achment Using Conf ig uration and Inter act iv e Mode • The to-address, cc-address, a nd subject ar e pre-configured.
Chapter 13 – SMTP Client Multi-Tech Systems, I nc. MultiConnect Serial-to-Serial A dapter User Guide (S000354A) 152 Sc enario 8 – Sending a M ime Encoded Binary Email wit h Att achment Using Inter.
Chapter 14 – POP3 Client Multi-Tech Systems, I nc. MultiConnect Serial-to-Serial A dapter User Guide (S000354A) 153 Chapter 1 4 – PO P3 Client Int roduction The MultiConnect IP can be configured as a POP3 cli ent to retrieve emails from a POP3 server.
Chapter 14 – POP3 Client Multi-Tech Systems, I nc. MultiConnect Serial-to-Serial A dapter User Guide (S000354A) 154 Example of the show recv-mail configuration Use the show recv-mail configuration to che ck the configuration.
Chapter 14 – POP3 Client Multi-Tech Systems, I nc. MultiConnect Serial-to-Serial A dapter User Guide (S000354A) 155 Sc enario 1 – Ret rie v ing Email s The command recv-mail mail can be used to retrieve all the emails from a POP3 server. Th is command will retrieve all the email with head ers, messag e body, and attachments.
Chapter 14 – POP3 Client Multi-Tech Systems, I nc. MultiConnect Serial-to-Serial A dapter User Guide (S000354A) 156 Sc enario 3 – Ret rie v ing the Em ail List Use the command recv-mail list to retrieve the email list containi ng the message number and the size of the individual messages (in octets).
Chapter 14 – POP3 Client Multi-Tech Systems, I nc. MultiConnect Serial-to-Serial A dapter User Guide (S000354A) 157 Sc enario 5 – Ret rieving First t Lines To retrieve the first few lines of an email, use the command recv -mail top <n> <t> , where n is the message number and t is the number o f lines to be retrieved.
Chapter 14 – POP3 Client Multi-Tech Systems, I nc. MultiConnect Serial-to-Serial A dapter User Guide (S000354A) 158 Error Messages • ERROR Invalid parameters. Check POP3 parameters This error message is displayed if the POP3 paramet ers are not configured correctly.
Chapter 14 – POP3 Client Multi-Tech Systems, I nc. MultiConnect Serial-to-Serial A dapter User Guide (S000354A) 159 Sc enario 8 – Sending a M ime Encoded Binary Email Using Interactiv e Mode Issue.
Chapter 15 – FTP Client Multi-Tech Systems, I nc. MultiConnect Serial-to-Serial A dapter User Guide (S000354A) 160 Chapter 15 – FTP Client Int roduction The FTP Client is used to establish a TCP session to the FTP server run ning on port 21. This chapter covers the FTP Client Feat ures and prov ides you with ten FTP Clien t Scenarios.
Chapter 15 – FTP Client Multi-Tech Systems, I nc. MultiConnect Serial-to-Serial A dapter User Guide (S000354A) 161 Prerequisites The host/serial device m ust ensure the validity of the following details before u sing FTP client: 1.
Chapter 15 – FTP Client Multi-Tech Systems, I nc. MultiConnect Serial-to-Serial A dapter User Guide (S000354A) 162 Sc enario 1 - List ing Directory C ontents This scenario describe s how to list the contents of the specified dire ctory of the FTP server without Automatic Authentication (default) a nd the data connection in A CTIVE mode.
Chapter 15 – FTP Client Multi-Tech Systems, I nc. MultiConnect Serial-to-Serial A dapter User Guide (S000354A) 163 Sc enario 3 - List ing Directory C ontents This scenario describe s how to list the.
Chapter 15 – FTP Client Multi-Tech Systems, I nc. MultiConnect Serial-to-Serial A dapter User Guide (S000354A) 164 Sc enario 5 - Sending a File to t he FT P Ser ver This scenario describe s how to send a file to the FTP server: a) Without Automatic Authentication (defau lt).
Chapter 15 – FTP Client Multi-Tech Systems, I nc. MultiConnect Serial-to-Serial A dapter User Guide (S000354A) 165 Sc enario 7 - Sending a File to t he FT P Ser ver This scenario describe s how to s.
Chapter 15 – FTP Client Multi-Tech Systems, I nc. MultiConnect Serial-to-Serial A dapter User Guide (S000354A) 166 Sc enario 9 - Re c eiv ing a File f rom the FT P Ser v er This scenario describe s .
Chapter 15 – FTP Client Multi-Tech Systems, I nc. MultiConnect Serial-to-Serial A dapter User Guide (S000354A) 167 Sc enario 10 - Re c eiv ing a File f rom the FT P Ser v er This scenario describe s.
Chapter 16 – SNTP Client Multi-Tech Systems, I nc. MultiConnect Serial-to-Serial A dapter User Guide (S000354A) 168 Chapter 1 6 – SN T P Client Int roduction SNTP Client is used to synchronize timekee ping among a set of distributed time servers and clients.
Chapter 16 – SNTP Client Multi-Tech Systems, I nc. MultiConnect Serial-to-Serial A dapter User Guide (S000354A) 169 Optional Prerequisites: The following configuration s are optional and can be used when you want the host device to enable dayli ght savings mode.
Chapter 16 – SNTP Client Multi-Tech Systems, I nc. MultiConnect Serial-to-Serial A dapter User Guide (S000354A) 170 Sc enario 1 - Updat ing T ime f rom the N T P Ser v er This scenario describe s the updating of time from the NTP server with Daylight Savings M ode disabled .
Appendix A – Flash Upgra de Multi-Tech Systems, I nc. MultiConnect Serial-to-Serial A dapter User Guide (S000354A) 171 Appendix A – F lash Upg r ade Int roduction The MultiConnect Adapter contains a 2 MB flash wher ein the boot image, the firmware and configu ration files are stored in a compressed format.
Appendix A – Flash Upgra de Multi-Tech Systems, I nc. MultiConnect Serial-to-Serial A dapter User Guide (S000354A) 172 Prerequisite 2 – Serial Port Configuration The default serial port parameters.
Appendix B – Regulatory Information Multi-Tech Systems, I nc. MultiConnect Serial-to-Serial A dapter User Guide (S000354A) 173 Appendix B – R eg ulator y Inf or mat ion Regulatory Information FCC .
Appendix C – Warrant y and Service Multi-Tech Systems, I nc. MultiConnect Serial-to-Serial A dapter User Guide (S000354A) 174 Appendix C – W arr ant y and Ser v ic e Multi-Tech Warranty Statement Multi-Tech Systems, Inc.
Appendix C – Warrant y and Service Multi-Tech Systems, I nc. MultiConnect Serial-to-Serial A dapter User Guide (S000354A) 175 Repair Procedures for International Distributors International distributors should co ntact their MTS International sales rep resentative for information about the rep airs for th eir Multi- Tech product.
Index Multi-Tech Systems, I nc. MultiConnect Serial-to-Serial A dapter User Guide (S000354A) 176 Inde x 3 32-bit Frame Check Sequenc e command +EFCS ..........102 9 9-Pin Connector ................................................................ 10 A Abort a File Transfer Session .
Index Multi-Tech Systems, I nc. MultiConnect Serial-to-Serial A dapter User Guide (S000354A) 177 Call waiting enable command +PCW ............................ 115 Caller ID command +VCID ......................................... 108 Carriage return c haracter S3 .
Index Multi-Tech Systems, I nc. MultiConnect Serial-to-Serial A dapter User Guide (S000354A) 178 dialout serial s0 ............................................................. 16 exit ..................................................................
Index Multi-Tech Systems, I nc. MultiConnect Serial-to-Serial A dapter User Guide (S000354A) 179 POP3 - Retrievi ng Emails Headers Scenario .................. 156 POP3 - Retrieving Emails Scenario ................................ 155 POP3 - Retrieving First t Lines S cenario .
Index Multi-Tech Systems, I nc. MultiConnect Serial-to-Serial A dapter User Guide (S000354A) 180 Set PPP user name IP comma nd ....................................... 44 Set primary DNS IP adddress IP command ...................... 23 Set secondary DNS IP adddress IP command .
Index Multi-Tech Systems, I nc. MultiConnect Serial-to-Serial A dapter User Guide (S000354A) 181 S10 ............................................................................. 119 S11 ................................................................
デバイスMulti-Tech Systems MTS2SA-T-Rの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Multi-Tech Systems MTS2SA-T-Rをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはMulti-Tech Systems MTS2SA-T-Rの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Multi-Tech Systems MTS2SA-T-Rの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Multi-Tech Systems MTS2SA-T-Rで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Multi-Tech Systems MTS2SA-T-Rを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はMulti-Tech Systems MTS2SA-T-Rの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Multi-Tech Systems MTS2SA-T-Rに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちMulti-Tech Systems MTS2SA-T-Rデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
