MultiquipメーカーDCA-400SPKの使用説明書/サービス説明書
ページ先へ移動 of 108
MQ POWER DCA-400SPK WHISPER W A TT TM GENERA TOR P AR TS AND OPERA TION MANUAL Re vision #0 (06/19/01) MUL TIQUIP INC. P ARTS DEP ARTMENT : 18910 WILMINGTON AVE. 800-427-1244 CARSON, CALIFORNIA 90746 F AX: 800-672-7877 310-537-3700 SERVICE DEP ARTMENT : 800-421-1244 800-835-2551 F AX: 310-537-3927 F AX: 310-638-8046 E-mail:mq@multiquip.
P A GE 2 — DCA-400SPK — P ARTS AND OPERA TION MANU AL— REV . #0 (06/19/01).
DCA-400SPK — PARTS AND OPERATION MANUAL — REV. #0 (06/19/01) — PAGE 3 HERE'S HOW TO GET HELP PLEASE HA VE THE MODEL AND SERIAL NUMBER ON-HAND WHEN CALLING P P P P P AR AR AR AR AR TS DEP TS.
P A GE 4 — DCA-400SPK — P ARTS AND OPERA TION MANU AL— REV . #0 (06/19/01) Here's How T o Get Help ............................................. 3 T able Of Contents ...................................................... 4 Rules For Safe Operation .
DCA-400SPK — PARTS AND OPERATION MANUAL — REV. #0 (06/19/01) — PAGE 5 P AR TS ORDERING PROCEDURES Get special freight allowances when you order 10 or more line items via F AX!** ■ UPS Ground S.
P A GE 6 — DCA-400SPK — P ARTS AND OPERA TION MANU AL— REV . #0 (06/19/01) R ULES FOR SAFE OPERA TION ■ NEVER touch the hot exhaust manif old, muffler or cylinder . Allow these par ts to cool before ser vicing engine or generator . ■ The engine of this generator requires an adequate free flo w of cooling air .
DCA-400SPK — PARTS AND OPERATION MANUAL — REV. #0 (06/19/01) — PAGE 7 R ULES FOR SAFE OPERA TION CAUTION : ■ Backfeed to a utility system can cause electrocution and.or property damage. Do not connect to any building's electrical system except through an approved device or after building main switch is opened.
P A GE 8 — DCA-400SPK — P ARTS AND OPERA TION MANU AL— REV . #0 (06/19/01) R ULES FOR SAFE OPERA TION ■ NEVER Run engine without air filter . Se vere engine damage ma y occur . ■ Always service air cleaner frequently to prevent carburetor malfunction.
DCA-400SPK — PARTS AND OPERATION MANUAL — REV. #0 (06/19/01) — PAGE 9 T ransporting ■ Alw ays shutdo wn engine before tr anspor ting. ■ Tighten fuel tank cap securely . ■ Drain fuel when transpor ting generator o ver long distances or bad roads.
P A GE 10 — DCA-400SPK — P ARTS AND OPERA TION MANU AL— REV . #0 (06/19/01) T o reduce the possibility of an accident while transpor ting the generator on public roads, always make sure the trailer (Figure 1) that suppor ts the generator and the to wing v ehicle are in good operating condition and both units are mechanically sound.
DCA-400SPK — PARTS AND OPERATION MANUAL — REV. #0 (06/19/01) — PAGE 11 Explanation of Chart: This section is intended to provide the user with trailer ser- vice and maintenance inf or mation. The ser vice and mainte- nance guidelines referenced in this section apply a wide range of trailers.
P A GE 12 — DCA-400SPK — P ARTS AND OPERA TION MANU AL— REV . #0 (06/19/01) s n o i t a c i f i c e p S . 1 e l b a T L E D O M N O I T A C I L P P A L E U F L L E C E K A R B M E T S Y S R W V .
DCA-400SPK — PARTS AND OPERATION MANUAL — REV. #0 (06/19/01) — PAGE 13 ) t ' n o C ( s n o i t a c i f i c e p S . 1 e l b a T L E D O M R E L P U O C S E R I T S L E E H W E L X A S B U H N O I S N E P S U S L A C I R T C E L E W 0 1 - R L R T S S A L C L L A B " 2 E L B A T S U J D A 2 C 3 1 - 5 7 1" 0 5 .
P A GE 14 — DCA-400SPK — P ARTS AND OPERA TION MANU AL — REV . #0 (06/19/01) DCA-400SPK — TRAILER SAFETY GUIDELINES Brakes If your trailer has a braking system, the brakes should be inspected the first 200 miles of operation. This will allow the brak e shoes and dr ums to seat properly .
DCA-400SPK — PARTS AND OPERATION MANUAL — REV. #0 (06/19/01) — PAGE 15 DCA-400SPK — TRAILER SAFETY GUIDELINES Hydraulic/Air/Surge Brakes Hydraulic brakes (Figure 3) should not require any special attention with the exception of routine maintenance such as shoe and lining replacement.
P A GE 16 — DCA-400SPK — P ARTS AND OPERA TION MANU AL — REV . #0 (06/19/01) Tires/Wheels/Lug Nuts Tires and wheels are a v er y impor tant and critical components of the trailer . When specifying or replacing the trailer wheels it is impor tant the wheels, tires , and axle are properly matched.
DCA-400SPK — PARTS AND OPERATION MANUAL — REV. #0 (06/19/01) — PAGE 17 s t n e m e r i u q e R e u q r o T n o i s n e p s u S . 3 e l b a T m e t I ) .
P A GE 18 — DCA-400SPK — P ARTS AND OPERA TION MANU AL — REV . #0 (06/19/01) NO TE: LIGHTS ARE ORIENTED FR O M THE DRIVER ’ S SEA T DCA-400SPK — TRAILER-WIRING DIA GRAM.
DCA-400SPK — PARTS AND OPERATION MANUAL — REV. #0 (06/19/01) — PAGE 19 g n i t o o h s e l b u o r T e k a r B c i r t c e l E . 5 e l b a T m o t p m y S e s u a C e l b i s s o P n o i t u l o S t n e t t i m r e t n I r o s e k a r B o N s e k a r B ? s e r i w n e k o r b r o s t i u c r i c n e p o y n A.
P A GE 20 — DCA-400SPK — P ARTS AND OPERA TION MANU AL — REV . #0 (06/19/01) g n i t o o h s e l b u o r T e k a r B c i l u a r d y H . 6 e l b a T m o t p m y S e s u a C e l b i s s o P n o i t u l o S s e k a r B o N? d e k n i k r o n e k o r b e n i l e k a r B.
DCA-400SPK — PARTS AND OPERATION MANUAL — REV. #0 (06/19/01) — PAGE 21 Machine Safety Decals The DCA-400SPK gener ator is equipped with a number of saf ety decals. These decals are pro vided for operator saf ety and maintenance inf or mation. The illustration below and on the preceding pages sho ws the decals as they appear on the machine .
P A GE 22 — DCA-400SPK — P ARTS AND OPERA TION MANU AL — REV . #0 (06/19/01) DCA-400SPK — OPERA TION AND SAFETY DECALS.
DCA-400SPK — PARTS AND OPERATION MANUAL — REV. #0 (06/19/01) — PAGE 23 DCA-400SPK — SPECIFICA TIONS s n o i t a c i f i c e p S . 7 e l b a T s n o i t a c i f i c e p S r o t a r e n e G l e .
P A GE 24 — DCA-400SPK — P ARTS AND OPERA TION MANU AL — REV . #0 (06/19/01) DCA-400SPK — GENERAL INFORMA TION DCA-400SPK F AMILIARIZA TION Generator The MQ P ow er Model DCA-400SPK is a 320 k.
DCA-400SPK — PARTS AND OPERATION MANUAL — REV. #0 (06/19/01) — PAGE 25 DCA-400SPK — GENERAL INFORMA TION Mechanical Governor System The mechanical governor system control the RPM of the engine. When the engine demands increase or decrease, the mechanical governor system regulates the frequency v ar iation to ±1.
P A GE 26 — DCA-400SPK — P ARTS AND OPERA TION MANU AL — REV . #0 (06/19/01) DCA-400SPK — MAJOR COMPONENTS Figure 6. Major Components.
DCA-400SPK — PARTS AND OPERATION MANUAL — REV. #0 (06/19/01) — PAGE 27 NO TE P A GE.
P A GE 28 — DCA-400SPK — P ARTS AND OPERA TION MANU AL — REV . #0 (06/19/01) DCA-400SPK — DIMENSIONS (T OP AND SIDE) Figure 7a. Dimensions.
DCA-400SPK — PARTS AND OPERATION MANUAL — REV. #0 (06/19/01) — PAGE 29 DCA-400SPK — DIMENSIONS (FRONT AND REAR) Figure 7b. Dimensions.
P A GE 30 — DCA-400SPK — P ARTS AND OPERA TION MANU AL — REV . #0 (06/19/01) DCA-400SPK — CONTR OL P ANEL Figure 8. Control Panel.
DCA-400SPK — PARTS AND OPERATION MANUAL — REV. #0 (06/19/01) — PAGE 31 DCA-400SPK — CONTR OL P ANEL The definitions below describe the controls and functions of the DCA-400SPK " Control Panel Control Panel Control Panel Control Panel Control Panel " (Figure 8).
P A GE 32 — DCA-400SPK — P ARTS AND OPERA TION MANU AL — REV . #0 (06/19/01) DCA-400SPK — ENGINE OPERA TING P ANEL Figure 10. Engine Operating Panel.
DCA-400SPK — PARTS AND OPERATION MANUAL — REV. #0 (06/19/01) — PAGE 33 The definitions below describe the controls and functions of the DCA-400SPK " Engine Operating Panel Engine Operating Panel Engine Operating Panel Engine Operating Panel Engine Operating Panel "(Figure 10).
P A GE 34 — DCA-400SPK — P ARTS AND OPERA TION MANU AL — REV . #0 (06/19/01) DCA-400SPK — OUTPUT TERMINAL P ANEL O VER VIEW Circuit Breakers T o protect the generator from an o verload, a 3-pole, 1000 amp, main main main main main circuit breaker is provided to protect the UVW output terminals from overload.
DCA-400SPK — PARTS AND OPERATION MANUAL — REV. #0 (06/19/01) — PAGE 35 DCA-400SPK — OUTPUT TERMINAL P ANEL O VER VIEW Legs O and Ground are considered Bonded Grounds.
P A GE 36 — DCA-400SPK — P ARTS AND OPERA TION MANU AL — REV . #0 (06/19/01) E L B A L I A V A S E G A T L O V . 8 E L B A T L E D O MK S S 0 0 4 A C D E G A T L O V E S A H P 3 ) E L B A T C E .
DCA-400SPK — PARTS AND OPERATION MANUAL — REV. #0 (06/19/01) — PAGE 37 How to read the output terminal gauges. The gauges and knobs on the control panel DO NO T effect the generator output in an y fashion. They are there to simply help the operator observe how much power is being supplied produced at the UVWO legs.
P A GE 38 — DCA-400SPK — P ARTS AND OPERA TION MANU AL — REV . #0 (06/19/01) 3 Phase, 240 V olt The following connection, with the voltage change-over board set into the 240V set position (See Figure 19), can off er THREE PHASE pow er at 240V .
DCA-400SPK — PARTS AND OPERATION MANUAL — REV. #0 (06/19/01) — PAGE 39 480 V olt Set position The voltage change-over board 480V set position uses all 6 plates in 3 diff erent connection places. There are 2 plates at every position (Every plate is used).
P A GE 40 — DCA-400SPK — P ARTS AND OPERA TION MANU AL — REV . #0 (06/19/01) CAUTION : An electric shock may happen when vibrators are used. P ay close attention to handling when operating vibrators and always use rubber boots and gloves to insulate the body from electrical shock.
DCA-400SPK — PARTS AND OPERATION MANUAL — REV. #0 (06/19/01) — PAGE 41 Figure 27. T ypical Generator Grounding Application DCA-400SPK — INST ALLA TION.
P A GE 42 — DCA-400SPK — P ARTS AND OPERA TION MANU AL — REV . #0 (06/19/01) General Inspection Prior to Operation The DCA-400SPK generator has been thoroughly inspected and accepted pr ior to shipment from the f actor y .
DCA-400SPK — PARTS AND OPERATION MANUAL — REV. #0 (06/19/01) — PAGE 43 Lubrication Oil Fill the engine crankcase with lubricating oil through the filler hole, but do not overfill.
P A GE 44 — DCA-400SPK — P ARTS AND OPERA TION MANU AL — REV . #0 (06/19/01) DCA-400SPK — PRE-SETUP Day-to-day addition of coolant is done from the reserve tank. When adding coolant to the radiator , DO NO T remo v e the radiator cap until the unit has completely cooled.
DCA-400SPK — PARTS AND OPERATION MANUAL — REV. #0 (06/19/01) — PAGE 45 DCA-400SPK — PRE-SETUP Battery Cable Installation AL W A YS be sure the batter y cab les (Figure 30) are proper ly connected to the batter y ter minals as shown belo w .
P A GE 46 — DCA-400SPK — P ARTS AND OPERA TION MANU AL — REV . #0 (06/19/01) DCA-400SPK — LO AD APPLICA TION Single Phase Load Always be sure to check the nameplate on the generator and equipment to insure the wattage, amperage and frequency requirements are satisfactorily supplied by the generator for operating the equipment.
DCA-400SPK — PARTS AND OPERATION MANUAL — REV. #0 (06/19/01) — PAGE 47 WARNING: Before Starting Engine 1. Check the lubricating oil lev el pr ior to star ting the engine. Mak e sure the generator is le v el. The oil lev el must be maintained between two notches on the dipstick.
P A GE 48 — DCA-400SPK — P ARTS AND OPERA TION MANU AL — REV . #0 (06/19/01) 4. Close all engine enclosure doors (Figure 34). Figure 34. Engine Enclosure Doors 5. Set the battery ON/OFF switch (Figure 35) to the ON position. Figure 35. Battery ON/OFF Switch 2.
DCA-400SPK — PARTS AND OPERATION MANUAL — REV. #0 (06/19/01) — PAGE 49 10 . The generator's frequency meter (Figure 41) displays the 60 cycle output frequency in HERTZ . Figure 41. Frequency Meter (Hz) Figure 42. V oltage Meter (V olts) 11 .
P A GE 50 — DCA-400SPK — P ARTS AND OPERA TION MANU AL — REV . #0 (06/19/01) 17. Observe the generator's ammeter (Figure 49) and verify that it reads the anticipated amount of current with respect to the load. Remember the ammeter will only display a current reading if the load is in use.
DCA-400SPK — PARTS AND OPERATION MANUAL — REV. #0 (06/19/01) — PAGE 51 DCA-400SPK — GENERA T OR ST ART -UP PR OCEDURE (A UT O) Before connecting this generator to any b uilding ’ s electr ical system, a licensed electrician must install an isolation (transfer) switch.
P A GE 52 — DCA-400SPK — P ARTS AND OPERA TION MANU AL — REV . #0 (06/19/01) Figure 52. MPEC Engine Running Status LED (OFF) NEVER stop the engine suddenly except in an emergency . DO NO T use the emergency stop switch a as method of shutting do wn the engine.
DCA-400SPK — PARTS AND OPERATION MANUAL — REV. #0 (06/19/01) — PAGE 53 NO TE P A GE.
P A GE 54 — DCA-400SPK — P ARTS AND OPERA TION MANU AL — REV . #0 (06/19/01) DCA-400SPK — MAINTENANCE General Inspection Prior to each use, the generating set should be cleaned and inspected for deficiencies. Check for loose, missing or damaged nuts, bolts or other fasteners.
DCA-400SPK — PARTS AND OPERATION MANUAL — REV. #0 (06/19/01) — PAGE 55 DCA-400SPK — MAINTENANCE 5. When the water level is near the mouth of the water filler , open drain plugs and star t the engine, and run at lo w idling. K eep the engine r unning at lo w idling and flush the radiator for about 10 minutes.
P A GE 56 — DCA-400SPK — P ARTS AND OPERA TION MANU AL — REV . #0 (06/19/01) Generator Storage For storage of the generator for over 30 days, the following is required: z Fill the fuel tank completely , lubr icate and change oil.
DCA-400SPK — PARTS AND OPERATION MANUAL — REV. #0 (06/19/01) — PAGE 57 . 5 1 E L B A T E C N A N E T N I A M / N O I T C E P S N I s r H 0 1 Y L I A D s r H 0 5 2 s r H 0 0 5 s r H 0 0 0 1 E N I.
P A GE 58 — DCA-400SPK — P ARTS AND OPERA TION MANU AL — REV . #0 (06/19/01) DCA-400SPK — GENERA T OR WIRING DIA GRAM.
DCA-400SPK — PARTS AND OPERATION MANUAL — REV. #0 (06/19/01) — PAGE 59 NO TE P A GE.
P A GE 60 — DCA-400SPK — P ARTS AND OPERA TION MANU AL — REV . #0 (06/19/01) DCA-400SPK — ENGINE WIRING DIA GRAM.
DCA-400SPK — PARTS AND OPERATION MANUAL — REV. #0 (06/19/01) — PAGE 61 DCA-400SPK — ENGINE WIRING DIA GRAM (MPEC).
P A GE 62 — DCA-400SPK — P ARTS AND OPERA TION MANU AL — REV . #0 (06/19/01) DCA-400SPK — TR OUBLESHOO TING (ENGINE) Practically all breakdowns can be prevented by proper handling and maintenance inspections, but in the event of a breakdown, use the tables shown for diagnosis based on the Engine T roub leshooting (T able 16).
DCA-400SPK — PARTS AND OPERATION MANUAL — REV. #0 (06/19/01) — PAGE 63 DCA-400SPK — TR OUBLESHOO TING (ENGINE) ) D E U N I T N O C ( G N I T O O H S E L B U O R T E N I G N E . 6 1 E L B A T M O T P M Y S M E L B O R P E L B I S S O P N O I T U L O S t o n s i n o i t u l o v e r e n i g n E .
P A GE 64 — DCA-400SPK — P ARTS AND OPERA TION MANU AL — REV . #0 (06/19/01) DCA-400SPK — TR OUBLESHOO TING (GENERA T OR/ENGINE) G N I T O O H S E L B U O R T R O T A R E N E G . 7 1 E L B A T M O T P M Y S M E L B O R P E L B I S S O P N O I T U L O S t u p t u O e g a t l o V o N ? e v i t c e f e d r e t e m t l o V C A .
DCA-400SPK — PARTS AND OPERATION MANUAL — REV. #0 (06/19/01) — PAGE 65 G N I T O O H S E L B U O R T C E P M . 8 1 E L B A T n o t p m y Se s u a C e l b i s s o Pn o i t u l o S e r u s s e r p l i o w o L . n o s i t h g i l ? l e v e l l i o w o L.
P A GE 66 — DCA-400SPK — P ARTS AND OPERA TION MANU AL — REV . #0 (06/19/01) How to read the marks and remarks used in this parts book. Items Found In the “ Remarks ” Column Serial Numbers- Where indicated, this indicates a serial number range (inclusiv e) where a par ticular par t is used.
DCA-400SPK — PARTS AND OPERATION MANUAL — REV. #0 (06/19/01) — PAGE 67 DCA-400SPK DCA-400SPK DCA-400SPK DCA-400SPK DCA-400SPK W/K W/K W/K W/K W/K OMA OMA OMA OMA OMA TSU SA6D140E-2 TSU SA6D140E-.
P A GE 68 — DCA-400SPK — P ARTS AND OPERA TION MANU AL — REV . #0 (06/19/01) DCA-400SPK GENERA T OR ASSY . GENERA T OR ASSY ..
DCA-400SPK — PARTS AND OPERATION MANUAL — REV. #0 (06/19/01) — PAGE 69 GENERA T OR ASSY . NO . P AR T NO . P AR T NAME QTY . REMARKS 1 8211000012 RO TOR ASSY .
P A GE 70 — DCA-400SPK — P ARTS AND OPERA TION MANU AL — REV . #0 (06/19/01) DCA-400SPK GENERA T OR ASSY . GENERA T OR ASSY ..
DCA-400SPK — PARTS AND OPERATION MANUAL — REV. #0 (06/19/01) — PAGE 71 GENERA T OR ASSY . NO . P AR T NO . P AR T NAME QTY . REMARKS DCA-400SPK GENERA T OR ASSY . 2 0 0041212000 PLAIN W ASHER 8 2 1 8201310014 C O VER, BEARING 1 2 2 8201312014 GASKET , BEARING 1 2 3 0010106065 HEX.
P A GE 72 — DCA-400SPK — P ARTS AND OPERA TION MANU AL — REV . #0 (06/19/01) DCA-400SPK CONTR OL BO X ASSY . CONTR OL BO X ASSY ..
DCA-400SPK — PARTS AND OPERATION MANUAL — REV. #0 (06/19/01) — PAGE 73 DCA-400SPK CONTR OL BO X ASSY . CONTR OL BO X ASSY . NO P AR T NO P AR T NAME QTY . REMARKS 1 8221812812 C ONTR OL BO X 1 2 0601801170 CURRENT TRANSFORMER, AMMETER . 3 ......
P A GE 74 — DCA-400SPK — P ARTS AND OPERA TION MANU AL — REV . #0 (06/19/01) CONTR OL BO X ASSY . DCA-400SPK CONTR OL BO X ASSY ..
DCA-400SPK — PARTS AND OPERATION MANUAL — REV. #0 (06/19/01) — PAGE 75 DCA-400SPK CONTR OL BO X ASSY . CONTR OL BO X ASSY . NO P AR T NO P AR T NAME QTY . REMARKS 3 0 0605011211 P I N 4 3 1 0601800470 FREQUENCY METER ............................
P A GE 76 — DCA-400SPK — P ARTS AND OPERA TION MANU AL — REV . #0 (06/19/01) DCA-400SPK ENGINE & RADIA T OR ASSY . ENGINE & RADIA T OR ASSY .
DCA-400SPK — PARTS AND OPERATION MANUAL — REV. #0 (06/19/01) — PAGE 77 DCA-400SPK ENGINE & RADIA T OR ASSY . ENGINE & RADIA T OR ASSY . NO . P AR T NO . P AR T NAME QTY . REMARKS 1 8210150104 ENGINE ......................................
P A GE 78 — DCA-400SPK — P ARTS AND OPERA TION MANU AL — REV . #0 (06/19/01) DCA-400SPK ENGINE & RADIA T OR ASSY . ENGINE & RADIA T OR ASSY .
DCA-400SPK — PARTS AND OPERATION MANUAL — REV. #0 (06/19/01) — PAGE 79 ENGINE & RADIA T OR ASSY . NO . P AR T NO . P AR T NAME QTY . REMARKS DCA-400SPK ENGINE & RADIA T OR ASSY . 3 3 0602010900 C A P , R E S E R V E T AN K 1 3 4 8212082103 B R A CKET , RESER VE T ANK 1 3 5 0229200600 R UBBER CUSHION 1 3 6 0017106025 HEX.
P A GE 80 — DCA-400SPK — P ARTS AND OPERA TION MANU AL — REV . #0 (06/19/01) DCA-400SSKENGINE OPERA TING P ANEL ASSY . ENGINE OPERA TING P ANEL ASSY .
DCA-400SPK — PARTS AND OPERATION MANUAL — REV. #0 (06/19/01) — PAGE 81 DCA-400SPK ENGINE OPERA TING P ANEL ASSY . ENGINE OPERA TING P ANEL ASSY . NO P AR T NO P AR T NAME QTY . REMARKS 1 9039211283 OPERA TING P ANEL 1 2 0017106016 HEX. HEAD BOL T 1 2 3 0602101000 B A TTER Y SWITCH 1 9827300090 4 0021008080 MACHINE SCREW 2 0030008000 HEX.
P A GE 82 — DCA-400SPK — P ARTS AND OPERA TION MANU AL — REV . #0 (06/19/01) DCA-400SSKENGINE OPERA TING P ANEL ASSY . ENGINE OPERA TING P ANEL ASSY .
DCA-400SPK — PARTS AND OPERATION MANUAL — REV. #0 (06/19/01) — PAGE 83 DCA-400SPK ENGINE OPERA TING P ANEL ASSY . ENGINE OPERA TING P ANEL ASSY . NO P AR T NO P AR T NAME QTY . REMARKS 4 0 0041420000 PLAIN W ASHER 3 2 4 1 3501860604 TERMINAL PLA TE 3 4 2 0019110040 HEX.
P A GE 84 — DCA-400SPK — P ARTS AND OPERA TION MANU AL — REV . #0 (06/19/01) DCA-400SPK — B A TTER Y ASSY . BA TTER Y ASSY ..
DCA-400SPK — PARTS AND OPERATION MANUAL — REV. #0 (06/19/01) — PAGE 85 BA TTER Y ASSY . NO . P AR T NO . P AR T NAME QTY . REMARKS 1 0168719052 B A TTER Y 2 2 0805018904 B A TTER Y SHEET 2 3 080.
P A GE 86 — DCA-400SPK — P ARTS AND OPERA TION MANU AL — REV . #0 (06/19/01) DCA-400SPK — MUFFLER ASSY . MUFFLER ASSY ..
DCA-400SPK — PARTS AND OPERATION MANUAL — REV. #0 (06/19/01) — PAGE 87 DCA-400SPK — MUFFLER ASSY . MUFFLER ASSY . NO . P AR T NO . P AR T NAME QTY .
P A GE 88 — DCA-400SPK — P ARTS AND OPERA TION MANU AL — REV . #0 (06/19/01) DCA-400SPK — FUEL T ANK ASSY . FUEL T ANK ASSY ..
DCA-400SPK — PARTS AND OPERATION MANUAL — REV. #0 (06/19/01) — PAGE 89 DCA-400SPK — FUEL T ANK ASSY . FUEL T ANK ASSY . NO . P AR T NO . P AR T NAME QTY .
P A GE 90 — DCA-400SPK — P ARTS AND OPERA TION MANU AL — REV . #0 (06/19/01) DCA-400SPK — ENCLOSURE ASSY . ENCLOSURE ASSY ..
DCA-400SPK — PARTS AND OPERATION MANUAL — REV. #0 (06/19/01) — PAGE 91 ENCLOSURE ASSY . NO . P AR T NO . P AR T NAME QTY . REMARKS 1 8215111022 BASE 1 2 3515116114 FLOOR P ANEL 1 3 8215116004 FLOOR P ANEL 1 4 0019208020 HEX. HEAD BOL T 1 4 5 8215020204 FRONT FRAME 1 8215102003 LINING 1 6 0019110025 HEX.
P A GE 92 — DCA-400SPK — P ARTS AND OPERA TION MANU AL — REV . #0 (06/19/01) ENCLOSURE ASSY . DCA-400SPK — ENCLOSURE ASSY ..
DCA-400SPK — PARTS AND OPERATION MANUAL — REV. #0 (06/19/01) — PAGE 93 ENCLOSURE ASSY . NO . P AR T NO . P AR T NAME QTY . REMARKS DCA-400SPK — ENCLOSURE ASSY .
P A GE 94 — DCA-400SPK — P ARTS AND OPERA TION MANU AL — REV . #0 (06/19/01) DCA-400SPK — ENCLOSURE ASSY . ENCLOSURE ASSY ..
DCA-400SPK — PARTS AND OPERATION MANUAL — REV. #0 (06/19/01) — PAGE 95 DCA-400SPK — ENCLOSURE ASSY . ENCLOSURE ASSY . NO . P AR T NO . P AR T NAME QTY .
P A GE 96 — DCA-400SPK — P ARTS AND OPERA TION MANU AL — REV . #0 (06/19/01) DCA-400SPK — ENCLOSURE ASSY . ENCLOSURE ASSY ..
DCA-400SPK — PARTS AND OPERATION MANUAL — REV. #0 (06/19/01) — PAGE 97 ENCLOSURE ASSY . NO . P AR T NO . P AR T NAME QTY . REMARKS DCA-400SPK — ENCLOSURE ASSY .
P A GE 98 — DCA-400SPK — P ARTS AND OPERA TION MANU AL — REV . #0 (06/19/01) DCA-400SPK — R UBBER SEAL ASSY ..
DCA-400SPK — PARTS AND OPERATION MANUAL — REV. #0 (06/19/01) — PAGE 99 R UBBER SEAL ASSY . NO . P AR T NO . P AR T NAME QTY . REMARKS 7 9 0228901450 R UBBER SEAL 3 8 0 0228901390 R UBBER SEAL 3 .
P A GE 100 — DCA-400SPK — P ARTS AND OPERA TION MANU AL — REV . #0 (06/19/01) DCA-400SPK — OIL PIPING ASSY . OIL PIPING ASSY ..
DCA-400SPK — PARTS AND OPERATION MANUAL — REV. #0 (06/19/01) — PAGE 101 DCA-400SPK — OIL PIPING ASSY . OIL PIPING ASSY . NO . P AR T NO . P AR T NAME QTY . REMARKS 1 0602023040 PUMP 1 2 8215191013 B RA CKET , PUMP 1 3 0017106025 HEX. HEAD BOL T 5 4 0017110030 HEX.
P A GE 102 — DCA-400SPK — P ARTS AND OPERA TION MANU AL — REV . #0 (06/19/01) DCA-400SPK — NAME PLA TE AND DECALS NAME PLA TE AND DECALS CONTR OL BO X GR OUP ENGINE OPERA TING P ANEL GR OUP.
DCA-400SPK — PARTS AND OPERATION MANUAL — REV. #0 (06/19/01) — PAGE 103 DCA-400SPK — NAME PLA TE AND DECALS NAME PLA TE ASSY . NO . P AR T NO . P AR T NAME QTY . REMARKS CONTR OL BO X GR OUP 2- 1 0800520100 P L A TE : ON-OFF ..................
P A GE 104 — DCA-400SPK — P ARTS AND OPERA TION MANU AL — REV . #0 (06/19/01) DCA-400SPK — NAME PLA TE AND DECALS NAME PLA TE AND DECALS BONNET GROUP B A TTER Y GR OUP ENGINE AND RADIA T OR GR.
DCA-400SPK — PARTS AND OPERATION MANUAL — REV. #0 (06/19/01) — PAGE 105 DCA-400SPK — NAME PLA TE AND DECALS NAME PLA TE ASSY . NO . P AR T NO . P AR T NAME QTY . REMARKS ENGINE & RADIA T OR GROUP 3- 1 6360610304 DECAL: W A TER ............
P A GE 106 — DCA-400SPK — P ARTS AND OPERA TION MANU AL — REV . #0 (06/19/01) P A YMENT TERMS T erms of payment f or par ts are net 10 da ys. FREIGHT POLICY All parts orders will be shipped collect or prepaid with the charges added to the invoice.
DCA-400SPK — PARTS AND OPERATION MANUAL — REV. #0 (06/19/01) — PAGE 107 NO TE P A GE.
HERE'S HOW TO GET HELP PLEASE HA VE THE MODEL AND SERIAL NUMBER ON-HAND WHEN CALLING P P P P P AR AR AR AR AR TS DEP TS DEP TS DEP TS DEP TS DEP AR AR AR AR AR TMENT TMENT TMENT TMENT TMENT 800/4.
デバイスMultiquip DCA-400SPKの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Multiquip DCA-400SPKをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはMultiquip DCA-400SPKの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Multiquip DCA-400SPKの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Multiquip DCA-400SPKで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Multiquip DCA-400SPKを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はMultiquip DCA-400SPKの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Multiquip DCA-400SPKに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちMultiquip DCA-400SPKデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
