MurphyメーカーA88の使用説明書/サービス説明書
ページ先へ移動 of 14
AUTOMA TIC ENGINE CONTROLLERS MODELS A88 AND A88-F INST ALLA TION MANUAL A88-8916N Revised 01-97 Section 40 (00-02-0196) ®.
T ABLE OF CONTENTS SECTION P AGE I INTRODUCTION 1 II SPECIFICA TIONS 1 IIA Power Requirements 1 IIB Input Requirements 1 IIC Output Ratings 1 III FRONT P ANEL DESCRIPTION 2 IIIA Description of LED Cal.
WARNING BEFORE BEGINNING INST ALLA TION OF THIS MURPHY PRODUCT ✔ Disconnect all electrical power to the machine. ✔ Make sure the machine cannot operate during installation. ✔ Follow all safety warnings of the machine manufacturer . ✔ Read and follow all installation instructions.
A. The Automatic Engine Controller , Model A88 and A88-F is designed to automatically start, monitor and stop electric start engines. The A88 comes in an all-weather case with a 5 foot cable and a plug for connection. The A88-F is the same system, but housed in a panel-mount case with terminals on back for connecting.
SECTION III: FRONT P ANEL DESCRIPTION 20s 15s 10s 5s CRANK AND REST TIME PICK UP PRESENT CRANK CRANK DISCONNECT IGNITION ON CRANK DISCONNECT OVER CRANK ENGINE TEMP. CHOKE OIL PRESSURE AUTO OFF TEST CRANK AND REST TIME IGNITION ON PICK UP PRESENT CRANK CRANK DISCONNECT CRANK DISCONNECT 20s 15s 10s 5s CHOKE OVER CRANK OIL PRESSURE ENGINE TEMP.
FRONT P ANEL DESCRIPTION Along with each description, an attempt has been made to clarify output and input connections according to their functions and terminals or wire color . A. Description of LED Callouts 1. IGNITION The ignition LED will come on when the system receives a signal to start.
In this section the terms Sink and Source are used. Sink: This terms refers to an output that switches to ground to do work. Source: This term will be used to refer to an output that is switched to positive to do work.
Refer to Diagrams 1 and 3: Basic Wiring Hookup for correct connections to your engine. Diagram 2 shows wire colors that correspond to the A88 plug and hookup wire, in the event of two colors the first color is the primary color and the other is a tracer color .
123 Grey Blue White/Black Green White/Red White/Brown Yellow Brown Green/White Brown/White Grey/White Red/White White White/Orange White/Yellow Violet/White Orange Red/White ground for 5 seconds Alarm.
7 Pin 1-wire-Wht/Blk: Breaker ignition I/P Pin 2-wire-Green: Vacuum switch I/P Pin 3-wire-Viol/Wht: Grnd for time delay I/P Pin 4-wire-Grey: Magnetic pickup I/P Pin 5-wire-Blue: Tach alternator I/P Pi.
8 123 6 7 5 8 2 1 18 20 4 17 16 15 23 21 22 9 19 Ground for 5 seconds Alarm On Start Connect SPST For Momentary T ype Operation Close to Run Open to Stop Ignition Connection Breaker T ype, 6 amp max I.
Terminal 1: Crank (source) Diagram 4: A88-F Wiring Terminals Terminal 2: Crank (sink) Terminal 3: Choke (sink) Terminal 4: Start I/P Terminal 5: Breaker ignition I/P Terminal 6: Magnetic pickup I/P Terminal 21: Common Terminal 22: Normally Closed (N.C.
Fuel V alve Start Float Switch 100 1/2 W Ignition N.O. Battery Pos. Ground Pickup Oil Level Switch Crank Diagram 5: A88/A88-F Wiring for Honda Generator Green Y ellow Ground for Alarm Before Start IN4005 Oil Press. Shutdown Grey/White Brown/White Stop White/Y ellow White/Brown Black Blue Red Black/White White Red/White Ignition N.
100 1/2 W Diagram 6: A88/A88-F Wiring for Honda Generator White Black Blue Red 18 ga White/Brown Grey/White Red/White Red/White A88 White/Orange 23 25 7 26 1 16 11 4 12 15 21 or A88-F E IG BA T LO ST .
デバイスMurphy A88の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Murphy A88をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはMurphy A88の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Murphy A88の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Murphy A88で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Murphy A88を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はMurphy A88の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Murphy A88に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちMurphy A88デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。