Murrayメーカー405011x48Aの使用説明書/サービス説明書
ページ先へ移動 of 52
The owner must be certain that all the product information is included with the unit. This information includes the INSTRUCTION BOOKS, the REPLACEMENT P ARTS and the W ARRANTIES. This information must be included to make sure state laws and other laws are followed.
2 F-050745L T ABLE OF CONTENTS W ARRANTY 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . RESPONSIBILITY OF THE OWNER 3 . . . . . . . . . . . . . . . . . . SAFETY RULES 3 . . . . . . . . . . . . . . . . . . . . . . . . .
OWNER’S INFORMA TION 3 F-050745L This instruction book is for several dif ferent models. The instructions ar e written for a person with some mechanical ability . Like most ser- vice books, not all the steps are described. Steps on how to loosen or tighten fasteners are steps anyone can follow with some mechanical ability .
OWNER’S INFORMA TION 4 F-050745L c. Do not turn sharply . Use care when backing. d. Use counterweights or wheel weights when suggested in the Instruction Book. 18. Do not operate this machine if you are taking drugs or other medication which can cause drowsiness or affect your ability to operate this machine.
SAFE MOWING GUIDE 5 F-050745L Each person that operates power equipment must learn to use correct and safe mowing procedures. T o help you learn, carefully read the following pages. Most of the time the operator was not correctly shown or did not read the instructions on the unit or in the Instruction Book before using the unit.
SAFE MOWING GUIDE 6 F-050745L mower was completely assembled at the store, you must still check the mower according to the assembly instructions. Make sure the mower is correctly assembled and that all fasteners are tight. Make sure the engine has the correct amount of oil.
SAFE MOWING GUIDE 7 F-050745L Also, the grass bagger will function better when the engine is operating at maximum speed. On slopes, decrease the ground speed and use care making sure the mower feels safe to operate. If the weather conditions are bad, do not mow .
STEPS T O FOLLOW 8 F-050745L BEFORE MOWING F Be sure to dress correctly . Wear hard shoes, not sandals or tennis shoes. F Examine the blade. A blade that is bent, cracked, or damaged must be replaced with a factory replacement blade. F Fill the fuel tank outside.
INTERNA TIONAL PICTORIALS 9 F-050745L INTERNA TIONAL PICTORIALS IMPORT ANT : Some of the following pic- torials are located on your unit or on literature supplied with the product. Be- fore you operate the unit, learn and un- derstand the purpose for each pictorial.
ASSEMBL Y 10 F-050745L ASSEMBL Y Read and follow the assembly and adjustment instructions for your mower . All fasteners are in the parts bag. Do not discard any parts or material until the unit is assembled. NOTE: In this instruction book, left and right describe the loca- tion of a part with the operator on the seat.
ASSEMBL Y 11 F-050745L HOW TO INST ALL THE SEA T 1. Carefully remove the plastic bag from the seat. Us e the fasteners shown below to install the seat . The fasteners are shown at full size. (A) 1001054 (B) 17x47 NOTE: Fasteners may be attached to seat for shipping purposes, if so remove fasteners before proceeding.
ASSEMBL Y 12 F-050745L MAINTENANCE FREE BA TTER Y IMPORT ANT : Before you attach the battery cables to the battery , check the battery date. The battery date tells if the battery must be charged. 1. Check the top and the side of the battery for the location of the battery date (Figure 3).
ASSEMBL Y 13 F-050745L IMPORT ANT! BEFORE YOU ST ART MOWING - Check the engine oil. - Fill the fuel tank with gasoline. - Check the air pressure of the tires. - Check the level of the mower housing. - Make sure the battery cables are attached. - Make sure the wire is attached to the spark plug.
OPERA TION 14 F-050745L Figure 4 Throttle Control Lever Blade Rotation Control Clutch / Brake Pedal Lift Lever Shift Lever LOCA TION OF CONTROLS BLADE ROT A TION CONTROL: Use the blade rotation control to start and stop the rotation of the blade and also to control various accessories, such as a snow thrower .
OPERA TION 15 F-050745L A TT ACHMENTS This unit can use many different attachments. See the attachment page in this book. This unit can pull attachments like a lawn sweeper , a lawn aerator , a hopper spreader or a small trailer . This unit can not use attachments that engage the ground like a plow , a disk harrow , or a cultivator .
OPERA TION 16 F-050745L HOW TO USE THE BLADE ROT A TION CONTROL The blade rotation control is next to the steering wheel (Figure 6). U s e the blade rotation control to engage the blade(s) or to operate a snow thrower attachment. 1. Before you start the engine, make sure the blade rotation con- trol is in the DISENGAGE position .
OPERA TION 17 F-050745L HOW TO SET THE P ARKING BRAKE 1. Completely push the clutch/brake pedal forward. 2. Lift the parking brake lever (Figure 7). 3. Remove your foot from the clutch/brake pedal and then release the parking brake lever . Make sure the parking brake will hold the unit.
OPERA TION 18 F-050745L HOW TO OPERA TE WITH THE MOWER HOUSING W ARNING: The deflector is a safety device. Do not re- move the deflector . The deflector forces the dis- charged material toward the ground. Always keep the deflector in the down position.
OPERA TION 19 F-050745L BEFORE ST ARTING THE ENGINE CHECK THE OIL NOTE: The engine was shipped from the factory filled with oil. Check the level of the oil. Add oil as needed. See the engine manufacturer ’ s instructions for the type of gasoline and oil to use.
OPERA TION 20 F-050745L OPERA TING TIPS 1. Check the blade rotation control for correct adjustment. For the blade(s) to disengage correctly , the adjustment must be cor- rect. 2. Before you use the unit, check the oil in the engine and add oil if necessary .
MAINTENANCE 21 F-050745L MAINTENANCE CHART PROCEDURE EACH USE FIRST 2 HOURS EVER Y 25 HOURS EVER Y 50 HOURS EVER Y 100 HOURS BEFORE STORAGE Blade, Inspect and Sharpen √ Blade Rotation Control, Check.
MAINTENANCE 22 F-050745L INSPECT BLADE W ARNING: Before you inspect or remove the blade, disconnect the wire to the spark plug. If the blade hits an object, stop the engine. Check the unit for dam- age. The blade has sharp edges. When you hold the blade, use gloves or cloth material to protect your hands.
MAINTENANCE 23 F-050745L HOW T O ADJUST THE BLADE ROT A TION CONTROL W ARNING: T o prevent an injury , the blade rotation control must operate correctly . In normal usage, the blade rotation control will not require an adjustment. However , if the cutting performance decreases or the quality of cut is poor , make the following changes.
MAINTENANCE 24 F-050745L HOW T O CHECK AND ADJUST THE DRIVE BRAKE Completely push the clutch/brake pedal forward. Set the parking brake. Move the shift lever to the neutral (N) position. Push the unit. If the rear wheels rotate, adjust or replace the brake pads.
MAINTENANCE 25 F-050745L HOW TO ADJUST THE SHIFT LEVER If the NEUTRAL position on the shift lever does not match neutral on the gearbox, adjust the shift lever as follows. 1. Stop the engine. 2 . Disconnect the adjuster nut from the shifter bracket (Figure 18).
MAINTENANCE 26 F-050745L WHERE TO LUBRICA TE Lubricate the areas shown with engine oil. Apply grease with a brush to the areas shown. NOTE: Apply grease to the steering gear assembly . CAUTION: If the unit is operated in dry areas that have sand, use a dry graphite spray to lubricate the unit.
W ARNING: The lift lever is spring loaded. Make sure the lift lever is locked in the LEVEL ADJUST- MENT position. Level Adjustment Position Figure 22 MAINTENANCE 27 F-050745L HOW TO REMOVE THE MOWER HOUSING 1. Move the blade rotation control to the DISENGAGE position.
MAINTENANCE 28 F-050745L HOW TO LEVEL THE MOWER HOUSING If the mower housing is level, the blade will cut easier and the lawn will look better . W ARNING: Before you make an inspection, adjust- ment, or repair to the unit, disconnect the wire to the spark plug.
MAINTENANCE 29 F-050745L HOW TO REPLACE THE MOTION DRIVE BEL T REMOV AL 1. Remove the mower housing. See the instructions on “How T o Remove The Mower Housing”. 2. Completely push the pedal forward and engage the parking brake. 3. Remove the idler pulley (Figure 27).
MAINTENANCE 30 F-050745L INST ALLA TION 1. Slide the motion drive belt between the stack pulley and the belt guides (Figure 30). Install the motion drive belt on the to p pulley of the stack pulley . Make sure the “V” side of the belt is against the pulley .
MAINTENANCE 31 F-050745L HOW TO REPLACE THE MOWER DRIVE BEL T 1. Remove the mower housing. See the instructions on “How T o Remove The Mower Housing”. 2. Pull the belt retainer away from the idler pulley and remove the mower drive belt (Figure 33).
MAINTENANCE 32 F-050745L HOW TO INST ALL THE WHEELS If the wheels must be removed for service, make sure they are installed as follows. Front Wheel 1. Make sure the valve stem is to the outside of the tractor . Slide the front wheel on the spindle (See Figure 34).
MAINTENANCE 33 F-050745L HOW TO REPLACE THE FUSE If the fuse is blown, the engine will not start. Remove the fuse and replace with a automotive fuse (Figure 36). Figure 36 Automotive Fuse HOW TO REPLACE THE LIGHT BULB 1. Raise the tractor hood. 2. Tur n the light socket until the tabs on the socket align with the notches in the bezel (Figure 37).
TROUBLE SHOOTING CHART 34 F-050745L PROBLEM: The engine will not start. 1. Follow the steps, “How T o Start The Engine” in this book. 2. Electric-Start Models: Clean the battery terminals. Tighten the cables. 3. Drain the fuel tank. Clean the fuel line.
F-050745L 35 Only use a factory repair part. Repair parts, except for the engine or the transmission, are available from the store where th e unit was purchased, a service shop recommended by the store, or an authorized service shop found in the yellow pages of the telephone di rectory .
REP AIR P ARTS MODEL 40501 1x48A 36 F-050745L CHASSIS & HOOD 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 24 21 22 23 25 26 27 54 29 28 53 32 33 34 35 31 36 37 38 16 39 40 41 42 50 16 16 43 .
REP AIR P ARTS MODEL 40501 1x48A 37 F-050745L CHASSIS & HOOD Key No. Part No. Description Key No. Part No. Description 1 690566 Seat 2 028x23 Cap, Push 0n 3 094057 Spring 4 26x229 Screw 5 1001054 .
REP AIR P ARTS MODEL 40501 1x48A 38 F-050745L MOTION DRIVE 1 2 3 4 5 6 7 8 9 10 12 11 13 14 15 16 60 18 19 20 17 21 62 55 22 23 25 26 27 28 30 31 32 33 35 17 41 29 17 40 39 40 38 45 37 46 49 48 50 53 .
REP AIR P ARTS MODEL 40501 1x48A 39 F-050745L MOTION DRIVE Key No. Part No. Description Key No. Part No. Description 1 009x39 Bolt, Shoulder 2 015x89 Nut, Hex 3 690173 Z Arm, Idler 4 094041 Z Rod, Clu.
REP AIR P ARTS MODEL 40501 1x48A 40 F-050745L STEERING 2 4 5 6 7 8 9 10 11 12 15 6 13 30 30 30 17 18 30 14 30 19 16 26 24 21 22 23 25 27 24 25 22 23 28 29 25 25 30 33 35 36 19 31 31 32 38 20 20 37 40 .
REP AIR P ARTS MODEL 40501 1x48A 41 F-050745L STEERING Key No. Part No. Description Key No. Part No. Description 1 1001980 Wheel, Steering 2 690625 Post, Steering 3 1001982 Cover , Steering Wheel 4 09.
REP AIR P ARTS MODEL 40501 1x48A 42 F-050745L MOWER HOUSING SUSPENSION 1 2 3 4 5 6 7 8 14 14 9 10 11 12 12 11 13 14 15 16 17 18 19 20 20 21 22 22 23 24 24 24 25 25 11 15 27 26 26 24 25 15 33 34 36 37 .
REP AIR P ARTS MODEL 40501 1x48A 43 F-050745L MOWER HOUSING SUSPENSION Key No. Part No. Description Key No. Part No. Description 1 092698 Grip 2 094157 Z Handle, PTO 3 094022 Z Pad, Switch 4 0025x3 Bo.
REP AIR P ARTS MODEL 40501 1x48A 44 F-050745L MOWER HOUSING 52 1 2 55 1 2 3 24 4 25 24 12 8 22 20 19 9 54 7 10 13 14 11 15 16 17 51 18 5 22 22 21 23 22 17 33 50 54 14 22 26 5 28 5 48 23 22 17 22 22 27.
REP AIR P ARTS MODEL 40501 1x48A 45 F-050745L MOWER HOUSING Key No. Part No. Description Key No. Part No. Description 1 092851 Pulley , Jackshaft 2 15x140 Nut, Hex 3 037x62 Belt, Mower Drive 4 690387 .
REP AIR P ARTS MODEL 40501 1x48A 46 F-050745L ENGINE MOUNT 1 6 7 8 9 10 11 12 13 14 15 15 21 22 22 21 2 3 4 5 26 30 31 9f 9a 9d 9b 9b 9c 23 23 9e 32.
REP AIR P ARTS MODEL 40501 1x48A 47 F-050745L ENGINE MOUNT Key No. Part No. Description 1 092317 Fuel Cap † 2 690280 Fuel T ank 3 095197 Hose Clamp † 4 7601033 Fuel Line (Must cut to length) † 5.
REP AIR P ARTS MODEL 40501 1x48A 48 F-050745L ELECTRICAL SYSTEM 24x32 94159 24x31 1001993 94613 21075 94136 GEAR DRIVE TRACTOR * AFTERFIRE SOLENOID OPTIONAL WIRING HARNESS FOR: MAIN HARNESS: 250x138 S.
REP AIR P ARTS MODEL 40501 1x48A 49 F-050745L ELECTRICAL SYSTEM Key No. Part No. Description 1 250x92 Harness, Light Wire 1001716 Socket, Light 090084 Bulb, Light 2 250x138 Harness, Chassis Wire 3 100.
50 F-050745L.
INDEX 51 F-050745L A Adjustments Blade Rotation Control, 23 Clutch, 24 Drive Brake, 24 Mower Housing, Level, 28 Shift Lever , 25 Attachments, 15, 52 B Battery Charge, 25 Check, 12 Clean, 25 Install, 1.
52 F-050745L LA WN TRACT OR ACCESSORIES Make your Lawn T ractor do more than you ever imagined. The accessories shown on this page can be used on your Lawn T ractor .
デバイスMurray 405011x48Aの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Murray 405011x48Aをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはMurray 405011x48Aの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Murray 405011x48Aの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Murray 405011x48Aで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Murray 405011x48Aを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はMurray 405011x48Aの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Murray 405011x48Aに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちMurray 405011x48Aデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。