Napoleon FireplacesメーカーSRPT03-XXXXの使用説明書/サービス説明書
ページ先へ移動 of 19
T a bletop P a tio Hea ter Owner ’ s Manual Standard: ANSI Z83.26-2007 / CSA 2.37-2007 ANSI Z83.26a-2008 / CSA 2.37a-2008 Gas-Fired Outdoor Infrared Patio Heaters. Questions, problems, missing / replacement parts? Before returning to your retailer , call our customer service department at 1-866-814-0585, 8 a.
2 This appliance can produce carbon monoxide which has no odor . Using it in an enclosed space can kill you. Never use this appliance in an enclosed space such as a camper , tent or home. DANGER CARBON MONOXIDE HAZARD W ARNING: Improper installation, adjustment, alteration, services or maintenance can cause injury , death or property damage.
3 PRECAUTIONS The installation must conform with local codes or , in the absence of local codes, with the National Fuel Gas Code, ANSI Z223.1/NFP A 54, NFP A58 Natural Gas and Propane Installation Code, CSA B149.1, or Propane Storage and Handling Code, B149.
4 PRECAUTIONS Within a partial enclosure which includes an overhead cover and three side walls, as long as 30 percent or more of the horizontal periphery of the enclosure is permanently open. This appliance requires 16.4oz (1lb) LP_gas supply cylinder .
5 35(&$87,216 35(&$87,216 35(&$87,216 35(&$87,216 WARNINGS AND CAUTIONS This heater is designed to operate with a standard 1 Ib propane cylinder with Approved Cylinder Connection.
6 P ARTS LIST Please check the contents of the packaging as to whether anything is missing! The fasteners used comply with ANSI/BL.1 1 Base 1 Housing 1 Burner Column 2 Emitter Screen Shield 1 Emitter .
7 Step 1 Step 2 ASSEMBL Y W ARNING : ONL Y AN AUTHORIZED GAS TECHNICIAN SHOULD INST ALL THIS PRODUCT . Step 2 Insert the three clamps of the burner column (3) into the three spring pieces of the housing (2) per the picture and screw over . Make sure the clamp and the spring piece fit together .
Step 4 ASSEMBL Y 8 Step 3 Attach emitter screen (5) to burner column (3) using three M4 x 8 bolts (9) Note: The ignition hole on emitter screen must line to the control knob. Step 4 Attach reflector dome (6) to emitter screen (5) using six 6mm washers (12) and three M6 nuts (1 1).
ASSEMBL Y 9 Step 5 Step 6 Step 5 Attach emitter screen shield (4) to burner column (3) using four M4 x 8 bolts (9). Step 6 Open the access door . Open up the gas bottle cover . Attach it to the regulator . Aim at the screw thread. T urn counter clockwise and tighten.
10 SAFETY CHECK Check for leak Your patio heater has been checked at all factory connections for leakage. To check the connections at the tube/regulator/cylinder. 1) Make leakage solution by mixing 1 part liquid dish soap and 3 parts water. 2) Spoon several drops (or use squirt bottle) of the solution onto the tube/regulator/cylinder connections.
11 OPERA TION Before turning gas supply ON W ARNING: DO NOT A TTEMPT TO OPERA TE HEA TER UNTIL YOU HA VE READ AND UNDERST AND ALL PRECAUTION . F AILURE TO DO SO CAN RESUL T IN SERIOUS PERSONAL INJUR Y , DEA TH, OR PROPERTY DAMAGE.
12 OPERA TION Flame Characteristic The flame pattern at the emitter screen should be visually checked whenever heater is operated. Normally the burner flame is blue, but little yellow flame is acceptable.
13 OPERA TION NOTE: The burner may be noisy when initially turned on. T o eliminate excessive noise from the burner , turn the Control Knob to the "LOW" position. Then, turn the knob to the level of heater desired. When heater is ON: Emitter screen will become bright red due to intense heat.
14 LOCA TING HEADER FOR USE CAUTION: WHEN CERT AIN MA TERIALS OR ITEMS ARE LEFT , ABOVE, BESIDE OR UNDER THIS HEA TER WHILE IN USE, THEY WILL BE SUBJECT TO RADIANT HEA T AND COULD BE SERIOUSL Y DAMAGED. This heater is primarily used for the heating of outdoor patios, decks, spas, pools and open working areas.
15 MAINTENANCE/ST ORAGE DO NOT touch or move heater for at least 45 minutes after use. Allow all burner elements to cool before touching. FOR YOUR SAFETY ; W ARNING: NOTE: In a salt-air environment (such as near an ocean). corrosion occurs more quickly than normal.
16 MAINTENANCE/ST ORAGE NOTE: wait until heater is cool before covering. T urn the control knob to "OFF" position. T urn clockwise to disconnect cylinder from regulator . Store heater upright in an area sheltered from direct contact with inclement weather (such as rain, sleet, hail, snow , dust and debris).
17 PROBLEM PROBABLE CAUSE SOLUTION Pilot will not light Gas valve may be OFF T urn the gas valve ON T ank fuel empty Refill LP gas tank Air in supply system Purge air from lines Loose connection Loose.
18 ONE-YEAR LIMITED WARRANTY The appliance has been manufactured under the highest standards of quality and workmanship. We warrant to the original consumer purchaser that all aspects of this product will be free of defects in material and workmanship for one (1) year from the date of purchase.
19 SRPT03-XXXX color m a t e r i a l & b a s e v e n t h o l e s h a p e reflector reflector 1. 1PC reflector 2. 2PCS reflector 3. 3PCS reflector venthole shape 1. Round 2.
デバイスNapoleon Fireplaces SRPT03-XXXXの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Napoleon Fireplaces SRPT03-XXXXをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはNapoleon Fireplaces SRPT03-XXXXの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Napoleon Fireplaces SRPT03-XXXXの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Napoleon Fireplaces SRPT03-XXXXで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Napoleon Fireplaces SRPT03-XXXXを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はNapoleon Fireplaces SRPT03-XXXXの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Napoleon Fireplaces SRPT03-XXXXに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちNapoleon Fireplaces SRPT03-XXXXデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
