Ask Proximaメーカー9100の使用説明書/サービス説明書
ページ先へ移動 of 103
USER’S GUIDE M ultimedia LCD P rojector (N ot actual front co ver).
WARRANTY Proxima Corporation warrants that the Proxima® Desktop Projector™ product manufactured b y Proxima is free from defects in materials and workmanship under normal use during the W arranty P eriod. The W arranty Period commences on the day of purchase b y the end-user .
Introducing the DP9100 i-1 Introducing the DP9100 The Proxima® Desktop Projector™ family consists of portable , color data and video LCD projectors that make sharing data and presenting information as easy as connecting y our computer to your monitor .
i-2 Introduction CYCLOPS INTERACTIVE POINTER SYSTEM All Proxima Desktop Projector products come Cy clops®-ready . The Cy clops interactive pointer s ystem functions like a cordless mouse , allowing y ou to control y our computer and software by pointing at the projection screen.
Introducing the DP9100 i-3 WHA T’S IN THE BOX? After y ou open the box and remov e the projector and the shrink-wrapped accessory packs, make sure y ou hav e all of the items sho wn below .
i-4 Introduction QUICK ST ART T o connect the projector to y our computer , read the section appropriate for your hardw are (or read Chapter 1, which lists these steps in greater detail).
Introducing the DP9100 i-5 Step 1: Setting up the projector 1 Place the projector on a solid, flat surface . 2 Position the projector so that the side with the handle is facing the projection screen. 3 Locate the arm release lever (see the next figure).
i-6 Introduction 5 Locate the flip mirror release lev er on the top of the arm (see Figure i-5). Push it in the direction of the arro w while pulling up on the lift tab .
Introducing the DP9100 i-7 6 Gently tilt the mirror to approximately 45 degrees . (Y ou can adjust the angle later to raise or lo wer the projected image .) Figure i-6, Flipping the mirror to a 45-degree angle CAUTION! Never push on or force the mirror .
i-8 Introduction Step 2: Connecting the computer In general, use the Proxima cable appropriate for your s ystem to connect your computer to the DP9 1 00.
Introducing the DP9100 i-9 Step 3: Connecting video and audio Connect audio and video sources to the projector , using this table as a guide . If you need more information, see the appropriate section in Chapter 2.
i-10 Introduction THE CYCLOPS REMOTE CONTROL AND CONTROL P ANEL 2 3 5 7 8 3 5 12 11 3 4 3 13 9 VOLUME PROXIMA ® MUTE MENU SETUP SOURCE PROG 2 PROG 1 –+ 3 8 9 ll 10 1 2 5 6 7 4 SOURCE FIT -TO-VIEW.
Introducing the DP9100 i-11 KEY FUNCTION 5 (V olume + / -) Adjusts the audio level. 6 Mute (remote Mutes the audio, or returns the sound. only) 7 Menu T urns the menus on and off. 8 Setup Adjusts the sync, contrast, brightness, tint, and image position settings.
Setting Up Your Projector 1-1 Chapter 1 Setting up y our projector OPENING THE PROJECTOR T o open the projector: 1 Place the projector on a solid, flat surface . 2 Position the projector so that the side with the handle is facing the projection screen.
1-2 Chapter One 3 The projector must be parallel to the floor . If y ou’re using a media cart, make sure the wheels are locked to prev ent it from moving.
Setting Up Your Projector 1-3 5 The arm pops up. Gently lift the arm. It raises automatically until it is fully extended. Do not f orce the arm further . Figure 1-4, The arm pops up 6 Locate the flip mirror release lev er on the top of the arm. Press it in the direction of the arrow while pulling up on the lift tab .
1-4 Chapter One 7 Gently tilt the mirror open to approximately 45 degrees (y ou can adjust the angle of the mirror later , to raise or lo w er the projected image). Figure 1-6, Opening the flip mirror CAUTION! Never push on or force the mirror . Always use care when opening the mirror assembly .
Setting Up Your Projector 1-5 O VER TEMP V OLUME SOURCE FIT -T O-VIEW P O WER CLEAR SETUP MENU REPL LAMP Figure 1-7, Accessing the recessed handle If you must mo ve the projector while it is open, grasp it securely at the sides by the lo w er part of the housing to support its weight.
1-6 Chapter One TURNING ON THE PROJECTOR The projector and the external monitor (if y ou’re using one) should be turned on befor e you turn on y our computer . This ensures that the computer properly senses the display during it’ s start-up process.
Setting Up Your Projector 1-7 CONNECTING THE PROJECTOR TO YOUR COMPUTER T ake a moment to review the projector’ s connector panel. Audio 1 In Audio Out MIC Cyclops Computer Audio In Audio 2 In Video 1 S-V ideo 1 S - Video 2 Video 2 Computer In Computer Out VGA Out Figure 1-10, The connector panel PORT CONNECTS TO.
1-8 Chapter One PORT CONNECTS TO... ...WITH THIS CABLE MIC Connects an external External microphone cable. microphone to the projector . COMPUTER Connects to the computer to PC: C800-6, Mac: C802-6, Sun: C801-6 IN bring computer video into the SGI: C943-6, DEC: C948-6.
Setting Up Your Projector 1-9 Audio In Computer In Figure 1-11, The projector’ s COMPUTER IN connector Y ou can display data on a separate monitor in addition to the projector . Computer out connections can be made with the projector and computer pow er on.
1-10 Chapter One PCs 1 Disconnect y our computer-to-monitor cable at the computer end. 2 Connect the free end of the monitor cable to the V GA OUT connector on the projector . 3 Use the Proxima V GA to LCD connector cable (C800-6) between the projector and the computer .
Setting Up Your Projector 1-11 PROJECTOR MACINTOSH P r o x i m a C a b l e Figure 1-14, The Proxima Mac to LCD adapter 3 Connect the free end of the Mac to LCD adapter to the projector’ s V GA OUT connector . Note: Macintosh users who do not connect an external monitor may need to set DP9100 sense lines to achieve the desired display resolution.
1-12 Chapter One Notebook computers Use the appropriate Proxima video cable to connect your notebook to the projector: 1 Connect the end of the Proxima video cable marked “COMPUTER” to the external monitor connector on y our notebook (or to the video cable adapter supplied with y our notebook).
Setting Up Your Projector 1-13 Workstations 13C3 Video Connections (except Silicon Graphics workstations) If your w orkstation has a 13C3 connector at the computer video port: 1 Disconnect y our computer-to-monitor cable at the computer end. 2 Connect the free end of the monitor cable to the projector’ s COMPUTER OUT connector .
1-14 Chapter One Silicon Graphics 13C3 V ideo Connections If you ha ve a Silicon Graphics w orkstation with 13C3 connectors at the computer and monitor video ports: 1 Disconnect y our computer-to-monitor cable at the computer end. 2 Connect the free end of the monitor cable to the Proxima SGI to LCD adapter (C947-12).
Setting Up Your Projector 1-15 DEC 3C3 Video Connections If you ha ve a DEC w orkstation with 3C3 connectors at the computer and monitor video ports: Figure 1-19, 3C3 connector 1 Disconnect y our computer-to-monitor cable at the computer end. 2 Connect the free end of the monitor cable to the Proxima DEC 3C3 to LCD adapter (C947-1 0).
1-16 Chapter One 3 Connect the optional Proxima BNC to LCD Connector Cable (C803-6) betw een the projector’ s COMPUTER OUT connector and the monitor’s BNC video input.
Setting Up Your Projector 1-17 CONNECTING VIDEO AND AUDIO TO THE PROJECTOR This section sho ws ho w to connect audio and video to your projector . The DP9 1 00 has multiple inputs for audio and video. If you are connecting only one audio or video source to your projector , use the VIDEO 1 and AUDIO 1 ports.
1-18 Chapter One The Composite Audio/Video cable (C497-6) has a y ellow , red, and white RCA plug at each end. T o connect an NTSC, PAL, or SECAM source to y our projector: CABLE PROJECTOR POR T VCR CONNECTOR (C497-6) Y ellow VIDEO 1 or 2. Video Out, T o Monitor , etc.
Setting Up Your Projector 1-19 Connecting external speakers The Desktop Projector 9 1 00 contains an internal stereo sy stem consisting of an amplifier and two speakers . Although this sy stem pro vides high-quality stereo output, a multimedia presentation may require external po w ered speakers or an external sound s ystem.
1-20 Chapter One Connecting an external stereo system T o connect the projector to an external stereo s ystem: 1 Using the Composite Video/A udio cable (C497-6), insert the white and red R CA plugs into the projector’s left and right A UDIO OUT ports.
Setting Up Your Projector 1-21 IMPOR T ANT PRECAUTIONS T o a void an y potential hazards to the projector , make sure the air intake and exhaust grills are unobstructed.
1-22 Chapter One T urning the lamp on and off The lamp is off when you first turn on the projector . Press the key on the on the Cyclops remote control or control panel to turn the lamp on. The green pow er indicator light illuminates. It takes a few seconds for the lamp to warm up.
Setting Up Your Projector 1-23 In the unlikely event that an o vertemperature conditions occurs , see Chapter 6, T roubleshooting for information on restarting your projector .
1-24 Chapter One Correcting keystoning The normal projected image will hav e a rectangular shape . An image is keystoned when it appears trapezoidal. Figure 1-30, Normal image vs.
Using Your Projector 2-1 Chapter 2 Using your projector The Desktop Projector 9 1 00 was designed with ease of use and simplicity in mind. With the Cyclops remote control or the control panel, most of the common functions are right at y our fingertips.
2-2 Chapter T wo Source key Use the Source key to switch between the v arious video input sources you connect, such as the computer video input, NTSC/P AL/SECAM video input, S-Video input, or MediaExpress input. Setup key Use the Setup key to make y our pre-presentation adjustments, such as s ync, brightness , contrast, tint, and image position.
Using Your Projector 2-3 Menu Press the Menu key to activate the onscreen menus . Press it again to exit the menus . / (Lamp on/off) This key turns the lamp on and off. On the remote , press and release this key once quickly to display a black screen.
2-4 Chapter T wo (Overtemp indicator light) This light illuminates if the projector becomes too hot or when one of the fans malfunctions . When this light is illuminated, the lamp automatically turns off. In the unlikely ev ent of an overtemperature condition, see Chapter 6, T roubleshooting for more information.
Using Your Projector 2-5 For most settings , y ou make incremental adjustments by moving a slide bar . T o mo ve a slide bar , press the edges of the MouseDisk, press the up and down arro w keys on the projector’ s control panel, or use the optional Cyclops w and or laser pointer .
2-6 Chapter T wo Adjusting the contrast T o adjust the contrast, press the Setup key until the Contrast slider appears . Press the edges of the MouseDisk, use the optional Cy clops wand or laser pointer , or press the left and right arrow keys to mov e the slider .
Using Your Projector 2-7 Switching to rear projection mode T o switch to rear projection mode (projecting from behind the projection screen instead of in fr ont of the screen), choose Projection , R ear from the Projector menu. ADJUSTING THE AUDIO Y ou can adjust the volume from the Cy clops remote control, the control panel, or the menus .
2-8 Chapter T wo Adjusting fade and balance The fade slider allow s you to choose betw een the projector's internal speakers and an external loudspeaker sy stem like the Proxima Po wered Loudspeaker Sy stem (A55). The balance slider allows y ou to control the level of sound betw een the left and right sides of y our sound system.
Using Your Projector 2-9 2 From the T ools menu, choose LightBoard mode , then specify whether y ou w ant the Overlay , WhiteBoard , or BlackBoard . 3 From the T ools menu, choose LightBoard , On . The Draw toolbar appears in the upper left corner of the projected image .
2-10 Chapter T wo 4 Select one of these buttons , then use the Cyclops w and, laser pointer , or the MouseDisk to dra w on the projected image . T o open the color palette: 1 Click the Color box or the icon in the upper right corner of the projected image .
Using Your Projector 2-11 If you find that y ou use LightBoard features frequently , consider programming either the Prog 1 or Prog 2 key , so you can access the LightBoard tool with the press of a key .
2-12 Chapter T wo Cyclops F/X Y our projector comes with Cyclops F/X—softw are effects that you can use to make your presentations more interesting and effectiv e . For more information on Cyclops F/X, see Chapter 4, Cyclops F/X . ADV ANCED FEA TURES There are several adv anced features of the DP9 1 00 that make giving presentations even easier .
Menus and Keys 3-1 Chapter 3 Menus and keys PROJECTOR MENUS The Main menu Menus Input Source Cyclops Advanced Image Projector Tools Audio Preferences Figure 3-1, The Main menu MENU WHA T IT CONT AINS T ools Settings for the LightBoard tool, Break T imer , and mouse tracking.
3-2 Chapter Three The T ools menu LightBoard Mode LightBoard WhiteBoard On BlackBoard Overlay Off Break Timer On Off Break Timer Value 15:00 Mouse Tracking Menus Input Source Cyclops Advanced Image Projector Tools Audio Preferences Figure 3-2, The T ools menu USE THIS .
Menus and Keys 3-3 The Cyclops menu Calibrate Button Calibrate Right None No Calibrate Left Center Menus Input Source Tools Advanced Image Projector Cyclops Audio Preferences Figure 3-3, The Cyclops menu USE THIS ...TO DO THIS: OPTION... Calibrate Starts the Cyclops calibration procedure.
3-4 Chapter Three The Input Source menu Source Select SourceMode Input Measurements Video 1 EWS1 (140 MHz) HSync: 0.00 KHz Current Mode: S-Video 1 Computer VSync: 0.00 Hz Lines: 0 Sense: HHHH Video 2 S-Video 2 Select Cancel EWS2 (130 MHz) EWS3 (135 MHz) 1280 x 1024 81.
Menus and Keys 3-5 The Image menu (computer or MediaExpress input source) Figure 3-5, The Image menu USE THIS ...TO DO THIS: OPTION... *Sync Adjusts the sync setting. *DotClk Adjusts the dot clock setting. Bright Adjusts the brightness of the image. Contrast Adjusts the RGB bias levels.
3-6 Chapter Three The Image menu (video or S-Video input source) Bright Contrast Menus Cyclops Tools Advanced Input Source Projector Image Audio Preferences Saturation Tint Figure 3-6, The Image menu USE THIS ...TO DO THIS: OPTION... Contrast Adjusts the video contrast.
Menus and Keys 3-7 The Audio menu Figure 3-7, The Audio menu USE THIS ...TO DO THIS: OPTION... V olume Adjusts the audio volume. Mute Mutes the audio or turns it back on. Balance Adjusts the left/right audio balance. Bass Adjusts the bass. T reble Adjusts the treble.
3-8 Chapter Three The Projector menu Projection Lamp Hours Lamp Hours Rear Reset Front No Reset 65:25:54 Menus Cyclops Tools Advanced Input Source Audio Projector Image Preferences Figure 3-8, The Projector menu USE THIS ...TO DO THIS: OPTION... Projection Switches between front and rear projection.
Menus and Keys 3-9 The Preferences menu Figure 3-9, The Preferences menu USE THIS ...TO DO THIS: OPTION... Colors Sets the number of colors to use. Language Sets the default language for the menus. On-screen Displays or hides the slide bars for sync, volume, contrast, tint, horizontal position, and vertical position.
3-10 Chapter Three The Advanced menu Figure 3-10, The Advanced menu USE THIS ...TO DO THIS: OPTION... User Sets a user profile of projector settings: • Defaults • User A (user defined) • User B (user defined) Hor . (Horizontal) Adjusts the horizontal position of the image on the screen.
Cyclops F/X 4-1 Chapter 4 Cyclops F/X Y our projector comes with Cyclops F/X — softw are effects that you can use to make your presentations more interesting and effectiv e .
4-2 Chapter Four INST ALLING CYCLOPS F/X Follo w these steps to install the Cyclops F/X softw are: 1 Insert the disk labeled Proxima Cyclops F/X into y our computer's floppy drive . 2 Do one of the follo wing: • In Window s 95, choose Start , Run , then type a:setup.
Cyclops F/X 4-3 The main screen of the F/X program appears: Figure 4-2, Cyclops F/X special effects On the left side of this windo w is a list of the special effects. The Assignments area in the middle of the window pro vides options that allow you to customize y our remote and software .
4-4 Chapter Four The Assignments area also contains fiv e buttons: BUTTON FUNCTION Setup Remote Lets you switch the assignments display between the included Cyclops remote control and the optional Cyclops wand or laser pointer . Put Away Minimizes the F/X screen.
Cyclops F/X 4-5 Note: T o access effects that are assigned to the Prog 1 and Prog 2 keys, assign the settings for those keys (in the projector's Preferences menu) to Host. USING THE CYCLOPS INTERACTIVE POINTER SYSTEM Y ou can use the Cyclops interactiv e pointer system with Cy clops F/X.
4-6 Chapter Four Click on the Edit Navigation Bar button. The follo wing screen appears: Figure 4-4, Edit Cyclops Navigation screen Use this screen to assign different options to the navigation bar . T o assign a new function to the na vigation bar , click the Next or Previous areas and assign a function using the list boxes to the right.
Cyclops F/X 4-7 SEE-IT/SHOW-IT See-it/Show-it is a feature of Cy clops F/X that previews the next slide in y our presentation on your computer monitor—without switching from the slide your audience sees .
4-8 Chapter Four FREEZE The Freeze option freezes the image on y our projector so you can use y our remote to control y our computer . This might be handy when you w ant to perform functions on your computer without distracting y our audience from your presentation.
Cyclops F/X 4-9 ST ARTING AN EFFECT Once you’v e customized an effect, you’re ready to use it. 1 Before the presentation, start Cy clops F/X, then minimize the main screen. 2 During your presentation, press the key or button that y ou assigned to each effect to start the desired effect.
4-10 Chapter Four Magnify enlarges a rectangular area around the mouse pointer . Y ou can choose from three levels of magnification (2 00 percent, 400 percent, or 800 percent). Note: T o enlarge the entire screen, use the Zoom effect. Next/Previous adv ances to the next or previous slide.
Cyclops F/X 4-11 T itle Screen projects an image from a .BMP file . Y ou can use this effect to show a predefined image with transition effects during a presentation. Y ou can also play an associated sound. Just specify which file to pla y and indicate whether to play it when the image appears or continuously .
4-12 Chapter Four Options menu The Options menu offers commands that allow y ou to set up assignments on the remote , wand, or laser pointer , change the look and feel of the cursor , and change the COM port settings.
Maintenance 5-1 Chapter 5 Maintenance Periodic maintenance will keep y our DP9 1 00 in top working condition. CLEANING THE LENS AND MIRROR T o clean the projection lens and mirror: 1 T ake a piece of lens tissue and form it into a loose sw ab .
5-2 Chapter Five Figure 5-1, Blowing air into the projector 2 T ake a piece of lens tissue and form it into a loose sw ab . W et it with a solution of approximately ten percent Isopropyl alcohol and w ater , and gently wipe it ov er the surface of the projection window .
Maintenance 5-3 REPLACING THE LAMP For best performance , you should replace the lamp after 7 00 hours of operation. Note: Do not touch the lamp with your bare hands.
5-4 Chapter Five 5 Locate the door to the lamp chamber on the right side of the left panel. It has one slotted captiv e screw . With a screw driver or coin, loosen the screw , then open the lamp chamber door (see Figure 5-3). Figure 5-3, Opening the lamp chamber door 6 Locate the thumbscrew on the right side of the lamp and unscrew it.
Maintenance 5-5 3 Slide the end of the lamp without the thumbscrew into the slot on the left side of the lamp chamber (see the Figure belo w). Figure 5-4, Sliding the lamp into place 4 Slide the end of the lamp with the thumbscrew into place , with the glass pinch-off on the lamp pointing up, and tighten the thumbscrew .
5-6 Chapter Five Figure 5-5, The three left-top retaining screws 3 Unsnap the top left cov er by lifting it up and pulling it out (see Figure 5-6). Figure 5-6, Lifting the top left cover out The filter is located on the inside of the top left co ver (see Figure 5-7).
Maintenance 5-7 4 There is a plastic grill cov ering the filter . Pull on the handle in the center of the grill to access the filter . T o replace the top co ver , reverse steps one through three , taking care to align the cov er before snapping it into place .
5-8 Chapter Five 4 Locate the screw s holding the main top cover in place (see Figure 5-9). R emov e the three screws and lift up on the screw mountings until the cov er is loose . Gently pull the cov er up and to the left of the projector until it releases.
Maintenance 5-9 6 Locate the three screw s at the top of the right side panel. R emove the screws and unsnap the panel, from the rear first. Figure 5-10, The screws at the top of the right side panel 7 The filters are no w exposed (see Figure 5-1 1). Remo ve the retaining screw to access the rear filter .
5-10 Chapter Five REPLACING THE BA TTERIES IN THE REMOTE CONTROL 1 Locate the battery compartment on the end of the remote control. Press down while y ou slide the cov er off of the compartment. Figure 5-12, Installing batteries in the remote control 2 R emov e the old batteries and replace them with new ones .
Troubleshooting 6-1 Chapter 6 T roubleshooting This chapter pro vides answers to some commonly asked questions about the Desktop Projector 9 1 00. TROUBLESHOOTING CHART Please refer to this troubleshooting chart and the following adjustment recommendations before calling for assistance .
6-2 Chapter Six PROBLEM LIKEL Y CAUSE POSSIBLE SOLUTION(S) Image off-center . Position controls (arrow keys) Adjust position controls. If or the Hpos/Vpos controls image will not center , check for in the menus. compatibility problems. Cannot get entire 1.
Troubleshooting 6-3 PROBLEM LIKEL Y CAUSE POSSIBLE SOLUTION(S) Remote control Batteries upside-down or old. Check battery placement or does not work. replace with new batteries. T iny dim or colored This is a normal LCD effect. None. points of light. Overtemp light 1.
6-4 Chapter Six 3 After y ou have determined y our video specifications, find the closest computer parameter entry in the compatibility list. Next, open the DP9 1 00’s Source Mode menu and scroll up or do wn through selections to find the closest source mode .
Troubleshooting 6-5 Adjusting the V ertical Position The V ert. Pos (V ertical Position) control adjusts the amount of blanking before each video frame .
6-6 Chapter Six Half-Normal Height Display Figure 6-3, Adjusting the half-normal height display Use the arro w keys, the Setup key on the control panel, or use the follo wing procedure to adjust the half-normal height display: 1 Press the Menu key . The Main menu display s.
Troubleshooting 6-7 V ertical Double Image Figure 6-4, Adjusting the vertical position Use the Setup key or the follo wing procedure to adjust the V ert. P os control: 1 Open the Main menu. 2 Select A dvanced . 3 Select V ert. Pos (V ertical Position).
6-8 Chapter Six Dark Lines in Fit-to-V iew Mode Only 1 With the menus closed, use the arrow key s on the control panel to pan the image do wn until it stabilizes. 2 A djust the contrast. 3 Change the colors to 226k. 4 Change the computer screen’ s background colors.
Troubleshooting 6-9 4 Check the Input Measurements windo w and record the V Sync, H Sync, and Lines v alues for the incoming video signal. Consult your computer’s documentation for the Video Data R ate (dot clock) specifications . Input Measurements V Sync: 72.
6-10 Chapter Six *Denotes interlaced models l e b a Lr e r u t c a f u n a Ms y S o e d i V / l e d o Mn o i t u l o s e Rk l C t o D ) z H M ( c n y S H ) z H K ( c n y S V ) z H ( 1 S W EI G Se m e r t x E , Z X , L X , 2 o g i d n I , y d n I4 2 0 1 x 0 8 2 10 4 17 9 .
Troubleshooting 6-11 l e b a Lr e r u t c a f u n a Ms y S o e d i V / l e d o Mn o i t u l o s e Rk l C t o D ) z H M ( c n y S H ) z H K ( c n y S V ) z H ( A S E Vc i r e n e G8 6 7 x 4 2 0 15 . 4 85 . 2 68 7 1 2 S W Ee l o p d a T3 k o o b C R A P S8 6 7 x 4 2 0 13 .
6-12 Chapter Six WHERE TO GET HELP If you still need help after checking the T roubleshooting Chart and making adjustments , or you need replacement parts , call your dealer’s technical support line . If your dealer cannot solv e your problem, please call Proxima Customer Service at: U.
Specifications A-1 Appendix A DP9100 SPECIFICA TIONS Color 16.7 Million Colors Display T echnology LCD: Active Matrix 1024 x 768 Resolution Multiple Graphics Modes (640 x 480, 800 x 600, 1024 x 768, 1152 x 900, 1280 x 1024 Contrast Ratio 100:1 T ypical Video Compatibility NTSC M 3.
Accessories and Replacement Parts B-1 Appendix B A ccessories and R eplacement Parts REPLACEMENT PARTS PART PART NUMBER Replacement lamp L71 Cyclops remote control A95 Power Cord, IEC, North America C.
B-2 Appendix B ACCESSORIES PART PAR T NUMBER MediaExpress Image Display System ME90H Cyclops Interactive Pointer System A2079 Cyclops Laser Pointer A90 Powered Loudspeaker System A55 Desktop Projector.
Sense Lines C-1 Appendix C Sense Lines This appendix explains ho w to adjust the projector if you’re having trouble connecting to a computer with no external monitor . WHA T ARE SENSE LINES? Certain displa y cards and video systems rely on sense line information from the monitor to correctly configure themselv es for display resolution.
C-2 Appendix C MACINTOSH DISPLA YS The next table show s typical sense line settings for Macintosh s ystems, based on the sy stem’s resolution. T ry these settings only if you ha ve trouble projecting an image without an external monitor connected to the computer .
Sense Lines C-3 Sense line settings for popular video cards: M E T S Y SR O D R A C C I H P A R G E P Y T R O T I N O M N O I T U L O S E RE S N E S 3 E S N E S 2 E S N E S 1 E S N E S 0 d r a k c a P.
Index Index A Adapters 1-8 Adjusting the volume V olume keys 2-7 Advanced features 2-12 Advanced menu 3-10 Hor . Pos 3-10 Sense 3, 2, 1, 0 3-10 User 3-10 VCO gain 3-10 V ert.
Index Correcting shimmering or streaks 2-6 Adjusting the Sync 2-6 Correcting vertical banding 2-6 Adjusting the Dot Clock 2-6 Adjusting the Red, Green, and Blue settings 2-6 Adjusting the T int 2-6 Cy.
Index K keystoning 1-24 L lamp replacing 5-3 installing the new lamp 5-4 lamp type A-1 removing the old lamp 5-3 Lamp indicator 2-4 Lamp key i-10, 1-22, 2-3 LightBoard tool 2-2, 2-8 Draw toolbar 2-9 l.
Index Q Quick Start i-4 connecting video and audio i-9 connecting your computer i-8 setting up the projector i-5 turning on the projector i-9 R rear projection 2-7 recessed carrying handle 1-4 remote .
デバイスAsk Proxima 9100の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Ask Proxima 9100をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはAsk Proxima 9100の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Ask Proxima 9100の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Ask Proxima 9100で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Ask Proxima 9100を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はAsk Proxima 9100の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Ask Proxima 9100に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちAsk Proxima 9100デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。