NECメーカー2690の使用説明書/サービス説明書
ページ先へ移動 of 29
MultiSync LCD2690WUXi SpectraV iew 2690 User ’ s Manual.
Index W arning, Caution ............................................................................................................... ......... English-1 Declaration ...................................................................................
English English-1 W ARNING CAUTION CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, MAKE SURE POWER CORD IS UNPLUGGED FROM W ALL SOCKET . T O FULL Y DISENGAGE THE POWER TO THE UNIT , PLEASE DISCONNECT THE POWER CORD FROM THE AC OUTLET .DO NOT REMOVE COVER (OR BACK).
English-2 Canadian Department of Communications Compliance Statement DOC: This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations. C-UL: Bears the C-UL Mark and is in compliance with Canadian Safety Regulations according to CAN/CSA C22.
English English-3 Contents Y our new NEC monitor box* should contain the following: • MultiSync LCD2690WUXi or SpectraView 2690 monitor with tilt/swivel/pivot/height adjust stand • Power Cord (Eur.
English-4 Figure C.1 Figure C.2 Highest Stand Position Quick Start To attach the LCD monitor to your system, follow these instructions: 1. T urn off the power to your computer . 2. For the PC or MAC with DVI digital output: Connect the DVI signal cable to the connector of the display card in your system ( Figure A.
English English-5 Figure E.1 V acation Switch Power Button Figure C.3 Figure D.1 Figure D.2 Figure C.4 7. Hold all cables firmly and place the cable cover onto the stand ( Figure D.1 ). T o remove the cable cover , lift the cover off as shown in Figure D.
English-6 Tilt Grasp top and bottom sides of the monitor screen with your hands and adjust the tilt as desired ( Figure TS.1 ). Figure TS.1 Swivel Grasp both sides of the monitor screen with your hands and adjust the swivel as desired ( Figure TS.2 ).
English English-7 Figure S.1 4. Place one hand around the base and one hand on the Quick Release Lever . Move the Quick Release Lever in the direction indicated by the arrows ( Figure S.2 ). 5. Lift up the bottom of the stand to unhook it from the monitor ( Figure S.
English-8 Controls OSM (On-Screen Manager) control buttons on the front of the monitor function as follows: To access OSM menu, press the EXIT button. To change signal input, press the INPUT/SELECT button. NOTE: OSM must be closed in order to change signal input.
English English-9 ECO MODE Decreases the amount of power consumed by reducing the brightness level. 1: Decreases the brightness by 25%. 2: Decreases the brightness by 50%. CUSTOM: Decreases the brightness level as determined by the user . Refer to the Advanced OSM menu for custom setting instructions.
English-10 AUTO FINE (Analog input only) This function automatically and periodically adjusts the “FINE” setting for change in signal condition. This function adjusts approximately every 33 minutes. EXP ANSION Sets the zoom method. FULL: The image is expanded to 1920 x 1200, regardless of the resolution.
English English-11 VIDEO DETECT Selects the method of video detection when more than one computer is connected. FIRST : The video input has to be switched to “FIRST” mode. When current video input signal is not present, then the monitor searches for a video signal from the other video input port.
English-12 OSM LOCK OUT This control completely locks out access to all OSM control functions. When attempting to activate OSM controls while in the Lock Out mode, a screen will appear indicating the OSM controls are locked out.
English English-13 Recommended use Safety Precautions and Maintenance FOR OPTIMUM PERFORMANCE, PLEASE NOTE THE FOLLOWING WHEN SETTING UP AND USING THE LCD COLOUR MONIT OR: • DO NOT OPEN THE MONITOR. There are no user serviceable parts inside and opening or removing covers may expose you to dangerous shock hazards or other risks.
English-14 CORRECT PLACEMENT AND ADJUSTMENT OF THE MONIT OR CAN REDUCE EYE, SHOULDER AND NECK F A TIGUE. CHECK THE FOLLOWING WHEN YOU POSITION THE MONITOR: • For optimum performance, allow 20 minutes for warm-up. • Adjust the monitor height so that the top of the screen is at or slightly below eye level.
English English-15 Specifications Monitor Specifications MultiSync LCD2690WUXi and Notes SpectraView 2690 Monitor LCD Module Diagonal: 64.9 cm/25.5 inches Active matrix; thin film transistor (TFT) V iewable Image Size: 64.9 cm/25.5 inches liquid crystal display (LCD); 0.
English-16 Features Ambix3 T echnology: T riple input technology allowing up to 3 input sources to be connected to a single monitor . The DVI-I connector supports both analog and digital input signals. Legacy analog input is supported using a traditional 15-pin VGA connector.
English English-17 T roubleshooting No picture • The signal cable should be completely connected to the display card/computer . • The display card should be completely seated in its slot. • Check the V acation Switch should be in the ON position.
English-18 Appendix If you need detailed information about the controls, please use the advanced menu. <How to use the advanced menu> •T urn of f your monitor . •T urn on your monitor by pushing the “POWER” and “INPUT/SELECT” button at the same time for at least one second simultaneously .
English English-19 T ag2 R-H.position Adjusts the position of the red component of the image. Press “Left” or “Right” to adjust. (Analog input only) G-H.position Adjusts the position of the green component of the image. Press “Left” or “Right” to adjust.
English-20 H. Size Adjusts the horizontal size of the screen. (Analog input only) If the “AUTO Adjust function” do not give you a satisfactory picture setting, a further tuning can be performed using the “H.Size (V .Size)” function (dot clock).
English English-21 T ag6 Color Control Colour Control Systems: Seven preset colour settings. For preset settings 1, 2, 3 and 5, the following levels can be adjusted: TEMPERA TURE: Adjust the white temperature by increasing or decreasing this setting.
English-22 Over Drive T urns the OVER DRIVE function on or off. Over Drive may reduce blurring that occurs in some moving images. When Over Drive is on, response time is improved. Side Border Color Adjusts the side black bars colour between black and white.
English English-23 Factory Preset Selecting Factory Preset allows you to reset all OSM control settings back to the factory settings. Highlighting the control to be reset and pressing the RESET button can reset individual settings. T ag9 Grayscale Mode This function changes the display image to monochrome.
English-24 T agA T ile Matrix Tile Matrix demonstrates multiple screens. This feature provides a single large screen using up to 25 monitors. It will be able to divide up to 5 each H and V . This requires you to feed the PC output into each of the monitors through a distributor .
English English-25 Using the Auto Brightness function The brightness of the LCD screen can be set to increase or decrease depending on the amount of ambient light within the room. If the room is bright, the monitor becomes correspondingly bright. If the room is dim, then the monitor will dim accordingly .
English-26 TCO’03 Congratulations! The display you have just purchased carries the TCO’03 Displays label. This means that your display is designed, manufactured and tested according to some of the strictest quality and environmental requirements in the world.
English English-27 NEC DISPLA Y SOLUTIONS is strongly committed to environmental protection and sees recycling as one of the company’ s top priorities in trying to minimize the burden placed on the environment.
デバイスNEC 2690の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
NEC 2690をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはNEC 2690の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。NEC 2690の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。NEC 2690で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
NEC 2690を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はNEC 2690の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、NEC 2690に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちNEC 2690デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
