NECメーカーDS1000の使用説明書/サービス説明書
ページ先へ移動 of 48
Cor dless T elephone User Guide (03.14.00) – Please Read – Important Cordless T elephone Installation Information DS1000/2000 900 MHz Cor dless T elephone Installation Tips • The cordless telephone base unit plugs into a digital station port. • For best results, the base unit should be placed in line-of-site with its handset.
This manual has been developed by NEC Unified Solutions, Inc. It is intended for the use of its customers and service personnel, and should be read in its entirety before attempting to install or program the system. Any comments or suggestions for improving this manual would be appreciated.
T able of Contents DS1000/2000 Cordless T elephone User Guide T able of Contents ◆ 1 Table of Contents Chapter 1: Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Introduction . . . . . . . . .
T able of Contents 2 ◆ T able of Contents DS1000/2000 Cordless T elephone User Guide Chapter 2: Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 Feature Operation . . . . . . . . . . . . . . . .
Introduction DS1000/2000 Cordless T elephone User Guide Chapter 1: Installation ◆ 1 1 Chapter 1: Installation Introduction DS1000/2000 900 Mhz Cordless T elephone DS1000/2000 900 Mhz Cor dless T ele.
The Basics Basic Operation 2 ◆ Chapter 1: Installation DS1000/2000 Cordless T elephone User Guide The Basics Basic Operation Using the Basic Features Answering Calls ■ Outside calls: Ring with 2 short rings follo wed by a long ring. ■ Inter com calls: Ring with 1 long ring.
The Basics Basic Operation DS1000/2000 Cordless T elephone User Guide Chapter 1: Installation ◆ 3 1 Using Y our Handset Figure 1: Using Y our Handset V oice Mail ● On if you have a V oice Mail message or Message W aiting.
Installation Installing the Base 4 ◆ Chapter 1: Installation DS1000/2000 Cordless T elephone User Guide Installation Installing the Base Connecting the Base T o connect the base to the DS1000/2000 system (F igur e 2: Installing the Base) : 1.
Installation Installing the Base DS1000/2000 Cordless T elephone User Guide Chapter 1: Installation ◆ 5 1 Figure 2: Installing the Base • Always raise the base unit antenna to its full v ertical position. • When installing more than one cordless in the same site: - Be sure the base units are at least 15 feet apart.
Installation Installing the Base 6 ◆ Chapter 1: Installation DS1000/2000 Cordless T elephone User Guide Figure 3: Correct Installation Methods Figure 4: Incorrect Installation Methods 80683 - 7 Correct line-of-site installation, away from devices that cause interference or locations that block signal.
Installation W all-Mounting the Base DS1000/2000 Cordless T elephone User Guide Chapter 1: Installation ◆ 7 1 Wall-Mounting the Base Mounting the Base on the W all T o mount the base on the wall (F igur e 5: Mounting the Base on the W all) : 1. Run the base line cord in the wide wire channel as shown, b ut do not plug it into the base.
Installation W all-Mounting the Base 8 ◆ Chapter 1: Installation DS1000/2000 Cordless T elephone User Guide Mounting the Base to a W all Plate T o mount the base on a standar d wall plate (F igure 6: Mounting the Base to a Standar d W all Plate) : 1.
Installation Installing the Battery DS1000/2000 Cordless T elephone User Guide Chapter 1: Installation ◆ 9 1 Installing the Battery Installing the Battery in your Handset T o install the battery in your handset (F igur e 7: Installing the Handset Battery) : 1.
Installation Charging the Handset 10 ◆ Chapter 1: Installation DS1000/2000 Cordless T elephone User Guide Charging the Handset Installing the Charger and Charging the Handset T o connect the A C Adaptor to the charger (F igure 8: Installing the Char ger) : 1.
Installation Charging the Handset DS1000/2000 Cordless T elephone User Guide Chapter 1: Installation ◆ 11 1 W all-Mounting the Charger T o wall-mount the char ger (F igur e 10: W all-Mounting the Char ger) : 1. Choose a suitable location for the charger w all-mount bracket within 6 feet of an A C outlet.
Installation Using the Belt Clip 12 ◆ Chapter 1: Installation DS1000/2000 Cordless T elephone User Guide Using the Belt Clip Installing the Belt Clip T o install the belt c lip (F igur e 11: Installing the Belt Clip) : ■ W ith the open end of the clip facing a way from the antenna, snap the belt clip onto the handset.
Installation Using the Earloop Style Headset with y our Cor dless T elephone DS1000/2000 Cordless T elephone User Guide Chapter 1: Installation ◆ 13 1 Using the Earloop Style Headset with your Cordl.
Installation Using the Earloop Style Headset with y our Cor dless T elephone 14 ◆ Chapter 1: Installation DS1000/2000 Cordless T elephone User Guide Ear Cushion Installation T o install the ear cushion (F igur e 15: Installing the Ear Cushion) : ■ Pull the ear cushion ov er the earpiece.
Installation Using the Earloop Style Headset with y our Cor dless T elephone DS1000/2000 Cordless T elephone User Guide Chapter 1: Installation ◆ 15 1 Connecting the Headset and Using the Controls T.
Installation Using the Headband Style Headset with y our Cor dless T elephone 16 ◆ Chapter 1: Installation DS1000/2000 Cordless T elephone User Guide Using the Headband Style Headset with your Cordl.
Installation Using the Headband Style Headset with y our Cor dless T elephone DS1000/2000 Cordless T elephone User Guide Chapter 1: Installation ◆ 17 1 ■ Remov e the ear cushion. Figure 19: Removing the Ear Cushion ■ Snap on the earloop ring. (Make sure the earloop ring lies fl at against the microphone boom as sho wn.
Installation Using the Headband Style Headset with y our Cor dless T elephone 18 ◆ Chapter 1: Installation DS1000/2000 Cordless T elephone User Guide Connecting the Headset and using the Controls T .
Installation Specifications and P ar ts DS1000/2000 Cordless T elephone User Guide Chapter 1: Installation ◆ 19 1 Specifications and Parts Specifications DS1000/2000 Cor dless T elephone Speci fi cations T ransmission and Reception T ransmission Method .
Installation Specifications and P ar ts 20 ◆ Chapter 1: Installation DS1000/2000 Cordless T elephone User Guide Parts and Accessories En vironmental En vironmental Speci fi cations . . . . . . . Maintain the same en vironmental conditions as you would for your DS1000/2000 ke ysets.
Feature Operation DS1000/2000 Cordless T elephone User Guide Chapter 2: Features ◆ 21 2 Chapter 2: Features Feature Operation Feature Operation Barge In Barge In is disabled by def ault. T o Barge In on an e xtension or line: 1. Call busy e xtension or place call on busy line.
Feature Operation 22 ◆ Chapter 2: Features DS1000/2000 Cordless T elephone User Guide T o use y our Call Coverage ke y to place a call to your idle co-w orker: 1. Press the Call Cov erage key . Call Forwarding Call Forw arding is enabled by default.
Feature Operation DS1000/2000 Cordless T elephone User Guide Chapter 2: Features ◆ 23 2 Callback Callback is enabled by default. T o leave a Callbac k at a b usy co-worker: 1. Call your busy co-w orker . 2. Dial 2 and hang up. - If you stay on the line, you will Camp-On to your b usy co-worker .
Feature Operation 24 ◆ Chapter 2: Features DS1000/2000 Cordless T elephone User Guide T o place an outside call using Line Gr oup Access: 1. Press T ALK and dial a Line Group Access Code (90-98). - If you hear dial tone as soon as you dial 9, your system has Line Gr oup Routing.
Feature Operation DS1000/2000 Cordless T elephone User Guide Chapter 2: Features ◆ 25 2 Distinctive Ringing Distinctiv e Ringing is enabled by default. T o change y our handset’ s ringing tone: - Outside calls ring with two short rings followed by one long.
Feature Operation 26 ◆ Chapter 2: Features DS1000/2000 Cordless T elephone User Guide Forced T runk Disconnect Forced T runk Disconnect is disabled by default. T o disconnect a b usy outside line: 1. Press line ke y for busy outside line. OR Press T ALK and dial the line’ s Line Access Code (e.
Feature Operation DS1000/2000 Cordless T elephone User Guide Chapter 2: Features ◆ 27 2 Hotline Hotline is disabled by default. T o place a call to y our Hotline partner: 1. Press your Hotline ke y . T o T ransfer y our outside call to y our Hotline par tner: 1.
Feature Operation 28 ◆ Chapter 2: Features DS1000/2000 Cordless T elephone User Guide Meet Me Conference Meet Me Conference is enabled by default. T o set up a Meet-Me Conference: 1. Press T ALK . 2. Dial *1 + Dial a page zone number + Announce Meet-Me Conference code (#11 or #12).
Feature Operation DS1000/2000 Cordless T elephone User Guide Chapter 2: Features ◆ 29 2 Night Service / Night Ring Night Service is disabled by default. T o activ ate or deactivate Night Service: 1. Press your Night key . T o answer a call ringing the pa ging system at night: 1.
Feature Operation 30 ◆ Chapter 2: Features DS1000/2000 Cordless T elephone User Guide Prime Line Preference Intercom Prime Line Preference is enabled by default. T o place a call on y our Prime Line: 1. Press T ALK + Dial the call normally . - T o bypass your Prime Line, pr ess another line ke y befor e pr essing T ALK.
Feature Operation DS1000/2000 Cordless T elephone User Guide Chapter 2: Features ◆ 31 2 Hotline Key 05 + Partner’ s extension Of f: Partner is idle On: Partner is ringing or b usy F ast Flash: P artner in DND for Intercom calls (option 2) or all calls (option 3).
Feature Operation 32 ◆ Chapter 2: Features DS1000/2000 Cordless T elephone User Guide Removing Lines and Extensions Removing Lines and Extensions is disabled by default. T o remo ves lines and extensions fr om service: 1. Press T ALK . 2. Dial #40 .
Feature Operation DS1000/2000 Cordless T elephone User Guide Chapter 2: Features ◆ 33 2 Reverse V oice Over Rev erse V oice Over is disabled by def ault. T o place a Rever se V oice Over call: 1. While on a handset call, press and hold your Re verse V oice Over k ey .
Feature Operation 34 ◆ Chapter 2: Features DS1000/2000 Cordless T elephone User Guide Speed Dial There are no Speed Dial numbers stored by default. Note: Y ou cannot program P ersonal or System Speed Dial bins from your Cordless T elephone. See your Communications Manager .
Feature Operation DS1000/2000 Cordless T elephone User Guide Chapter 2: Features ◆ 35 2 T andem T runking T andem T runking is disabled by default. T o set up a tandem call (Unsupervised Conference): 1. Place or answer an outside call. 2. Press CONF .
Feature Operation 36 ◆ Chapter 2: Features DS1000/2000 Cordless T elephone User Guide T runk (Line) Queuing and Callback T runk (Line) Queuing and Callback are disabled by default. T o queue f or a busy line: 1. Press line ke y for busy line. OR Press T ALK and dial line’ s Direct Line Access code (e.
Feature Operation DS1000/2000 Cordless T elephone User Guide Chapter 2: Features ◆ 37 2 2. Press TRANSFER + Dial your co-worker’ s extension. 3. Dial 8 . - T o T ransfer the call to your own mailbox, pr ess your o wn Message Center k ey . 4. Press T ALK to hang up.
Feature Operation 38 ◆ Chapter 2: Features DS1000/2000 Cordless T elephone User Guide W alking Class of Service W alking Class of Service is disabled by default. T o enable W alking Class of Service at a co-worker’ s cordless telephone: 1. Press T ALK + Dial ##0 .
Feature Summary DS1000/2000 Cordless T elephone User Guide Chapter 2: Features ◆ 39 2 Feature Summary Cordless T elephone Feature Summary DS1000/2000 Cor dless T elephone Feature Summary (P age 1 of.
Feature Summary 40 ◆ Chapter 2: Features DS1000/2000 Cordless T elephone User Guide Hold, Intercom Y es Enabled Hold, System Ye s Enabled Hotline Y es Disabled Interactiv e Soft K eys No N/A Last Number Redial Y es Enabled Handset feature. Enhanced Last Number Redial not av ailable.
Feature Summary DS1000/2000 Cordless T elephone User Guide Chapter 2: Features ◆ 41 2 V oice Over Y es Disabled Handset cannot recei ve a V oice Over . V olume and Contrast Control Ye s Enabled V olume control is a handset feature. Contrast Con- trol is not av ailable.
Feature Summary 42 ◆ Chapter 2: Features DS1000/2000 Cordless T elephone User Guide.
NEC Unified Solutions, Inc. 4 Forest Parkway , Shelton, CT 06484 T el: 800-365-1928 Fax: 203-926-5458 www.necunifiedsolutions.com Other Important T elephone Numbers Sales: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .203-926-5450 Customer Service: .
*80683INS01* 80683INS01 June 21, 2004 Printed in U.S .A. NEC Uni fi ed Solutions, Inc. 4 F orest P arkway , Shelton, CT 06484 TEL: 203-926-5400 F AX: 203-929-0535 www .
デバイスNEC DS1000の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
NEC DS1000をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはNEC DS1000の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。NEC DS1000の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。NEC DS1000で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
NEC DS1000を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はNEC DS1000の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、NEC DS1000に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちNEC DS1000デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。