NECメーカーNP01WK1の使用説明書/サービス説明書
ページ先へ移動 of 17
W all Mount Unit NP01WK/NP01WK1 Installation and Adjustment Manual English Deutsch Fr ançais Italano Español Português Русский T ürk çe Polski 中文 한글 日本語 Printed in Croatia © NEC Displa y Solutions, Ltd.
ENG-1 W all Mount Unit NP01WK/NP01WK1 Installation and Adjustment Manual Thank you for your purchase of this NEC wall mount unit. Please read this installation and adjustment manual car efully to ensure pr oper use. The W all Mount Unit NP01WK/NP01WK1 is exclusively for Projector U300X/U250X/ U310W/U260W and cannot be used for other projectors.
ENG-2 ENG-3 Please heed the following Symbol In this “Installation and Adjustment Manual”, to ensure the safe and proper use of the product, prevent harm to yourself and others and damage to property , various symbols ar e used. The symbols and meanings are as follows.
ENG-2 ENG-3 W arning • Do not install in places subject to constant vibration. Extended vibration may cause loosening of the screws and result in the Wall Mount Unit and projector falling and causing injury .
ENG-4 ENG-5 Pr eparation Packaged Parts Please check the packaged items. W all adapter:1 Arm:1 Projector adapter:1 W all plate:1 *1 M5 screws:4 *2 *1, *2:T o be used when mounting the wall adapter in the North America region. Cover (A, B):2 pairs Arm cover:1 Plate (B):1 M4 screws:4 M3.
ENG-4 ENG-5 V ertical adjust/ Arm fixation knobs Arm cover Elongate hole for screw (or bolt) (4 parts) Covers (A, B) Plate (A) Arm fixation screw Grooves for wiring Arm Tilt adjust knobs (4 parts) C.
ENG-6 ENG-7 Dimensions of Parts: (unit: mm) The dimensions of the positions of the wall fixation screws (bolts) of the wall adapter are described.
ENG-6 ENG-7 Mounting the Pr ojector Preparations 1. Determine the installation location of the screen, and accordingly decide the installation position of the wall mount unit. Refer to the section "Installation" in the user’ s manual included with the projector for more information.
ENG-8 ENG-9 c Align the projector adapter with the holes on the bottom of the projector and securely attach the adapter with the four supplied screws (M4x20). d Loosen the vertical adjust/arm fixation knobs of the projector adapter . Caution Do not try to attach the projector adapter without the foam packing spacers in place.
ENG-8 ENG-9 b a 3. Attach the arm to the wall adapter . a Loosen the arm fixation screws (top and bottom) with the supplied hex wrench. b Insert the arm plate (A) into the wall adapter from the top and tighten the screws (top and bottom) near the center of the elongated hole.
ENG-10 ENG-11 b Use the two supplied M5.5x9.5 screws to securely attach the supplied plate (B) to the arm. c Remove the cable cover of the projector . b c Plate (B) W ar ning If plate (B) is not installed, the projector may slide out of the arm and fall off, which may cause injury .
ENG-10 ENG-11 5. Cabling a The power cord and signal cables can be passed through the grooves for wiring on the left and right side of the arm. This should be done before attaching the arm cover . T ake care not to squeeze the cables with the horizontal adjust screws.
ENG-12 ENG-13 Adjusting the Pr ojection Position Pr eparations Before adjusting • Project an image from the projector , then rst use the focus lever of the projector to roughly adjust the focus of the projected image.
ENG-12 ENG-13 d c c T ur n the left or right knob to adjust projector tilt in the left or right direction. - When the knob shown in black in the illustration is tightened, the projector is rotated in the counterclockwise dir ection. d When the adjustm ent is complete, tighte n the opposite knob that is still loosened.
ENG-14 ENG-15 4. Adjust the tilt. Tilt adjustment is performed with the four adjustment knobs. Front/r ear tilt adjustment Adjust together Rotation axis Adjust together Rotation axis Left/righ.
ENG-14 ENG-15 5. Attach the covers to the pr ojector adapter and the wall adapter . a Attach cover (A) (with hook) and cover (B) (with notch) to the upper side of the wall adapter . Slide the two covers towards the center while pushing them down, as shown in the illustration.
ENG-16 Specifications Product name: W all mount unit Model: NP01WK/NP01WK1 Adjustmentangle: Up-downangle±3°,left-rightangle±3°,inclinationangle±10° Adjustmentwidth: Front-r ear±100mm,left-right±50mm,up-down±50mm External dimensions: 280 (W) x 541(D) x 219 (H) mm Weight: Approx.
デバイスNEC NP01WK1の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
NEC NP01WK1をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはNEC NP01WK1の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。NEC NP01WK1の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。NEC NP01WK1で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
NEC NP01WK1を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はNEC NP01WK1の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、NEC NP01WK1に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちNEC NP01WK1デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。