NECメーカーNP03CMの使用説明書/サービス説明書
ページ先へ移動 of 16
Portable Projector NP03CM Ceiling Mount Unit Installation and Adjustment Manual Thank you for your purchase of the NEC portable projector ceiling mount unit. Please read this installation and adjustment manual carefully to ensure proper use. Special skills are required for the installation of the portable projector.
2 Heed the Follo wing • When installing the projector, be sure to do so as explained in this manual. The projector may fall and cause injury if it is installed improperly. • To prevent the projector from falling, install it in a place and fasten it in a way with sufficient strength to support the combined weight (4.
3 CA UTION • Do not obstruct the projector's ventilation holes. Doing so will prevent the dissipation of heat and may result in fires. In particular, do not use the projector in the following ways: Do not install the projector in a wall or in a tight place where ventilation is poor, place a cover it, etc.
4 • Distance to lens end Center line of fixed ceiling part Lens center 70 105.2 162.5 90 90 60 60 80.4 10 4 - Preparation List of P acka ged Parts Fixed ceiling part ...1 Projector mounting adapter ...1 Projector mounting screws (M 4)...3 Up-down angle adjustment screws (M5 ) .
5 Zoom adjustment range 25 0123456789 1 0 12(m) 40 60 80 100 120 150 180 200 240 300 11 Wide angle (Maximum) Telephoto (Maximum) Guide to Screen Size and Projector Mounting Position Screen Size and Pr.
6 Guide to Screen Size and Projector Mounting Position 25 01234567 8 9 1 0 11(m) 40 60 80 100 120 150 180 200 240 300 ( 型 ) Screen Size and Projection Distance···VT48/VT49 Use this guide when considering the distance to the screen and the screen size.
7 Guide to Screen Size and Projector Mounting Position Zoom adjustment range 25 0123456789 1 0 12(m) 40 60 80 100 120 150 180 200 240 300 11 Telephoto (Maximum) Wide angle (Maximum) Screen Size and Projection Distance···VT695 Use this guide when considering the distance to the screen and the screen size.
Guide to Screen Size and Projector Mounting Position 8 (m) 25 0 0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0m 40 60 80 100 120 150 180 200 240 270 300 (Inches).
9 1 Mounting the Pr ojector Attach the Fixed Ceiling P ar t to the Ceiling First, partially tighten the four screws, then tighten the screws firmly after positioning. Use M8 bolts for the fixed ceiling part. Use of types other than M8 could cause the projector to fall.
10 3 4 Mounting the Projector Suspend the Projector fr om the Fixed Ceiling P ar t Slide the slotted part of the projector mounting adapter over the pin of the fixed ceiling part and push all the way to the back.
Mounting the Projector 11 NOTE : Mounting boards, M8-type anchor nuts, bolts, nuts and washers are commercially available. Mounting board (Strong enough to support the weight of the whole unit.
12 1 2 3 Replacing the Lamp To replace the lamp, first switch off the power, wait for the cooling fans to stop and disconnect the power plug from the outlet. Now, wait about 60 minutes before replacing the lamp. Attempts to replace the lamp during operation or immediately after operation has stopped will cause burns because of the high temperature.
13 1 10 ˚ 10 ˚ 上下端 Upper and lower edges Adjustment of the Pr ojection Angle Before the Adjustment • Refer to the instruction manual of the projector, switch on the power and project an image. • Refer to the section "Orientation " of Setup and select the projection orientation.
10 ˚ 1 0 ˚ 14 Left and right edges 10 ˚ 10 ˚ 2 3 Adjustment of the Projection Angle Adjust the Up-Down Angle Turn the projector up and down so that the left and right edges of the screen are parallel, then firmly tighten the four up-down angle adjustment screws.
15 Adjustment of the Projection Angle Fine Adjustment After the adjustments, chec k that the par ts are fixed securel y . Loosen the same screws that were used in the distortion adjustment and finely adjust the angle so that the projected image fits the screen, then tighten all the screws (i.
MEMO NP03CM_E 07.3.12 2:15 PM ページ 16.
デバイスNEC NP03CMの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
NEC NP03CMをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはNEC NP03CMの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。NEC NP03CMの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。NEC NP03CMで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
NEC NP03CMを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はNEC NP03CMの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、NEC NP03CMに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちNEC NP03CMデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。